A small electric fence kit works once four things line up: posts and wire in place, a ground rod driven deep, an energizer matched to your wire length, and a voltage test at the far end.
Most kits ship as a physical fence package, not a working electrical system. Skip the grounding step and the fence still won’t hold anything in.
What Comes In A Small Electric Fence Kit?
A typical kit covers the fence structure — posts, wire, clips, and a ground rod — while the energizer, connectors, and fence tester are usually bought on top. Count your parts before you dig anything.
- Posts — the Parmak kit supplies eight 2-foot fiberglass posts, enough for a small garden or barn lot.
- Wire — 100 feet of 20-gauge galvanized wire. Smooth wire only; never electrify barbed wire, which is a safety hazard.
- Ground rod — 2 feet of galvanized rod in the Parmak kit, with a clamp to match.
- Energizer — sold separately. It must match your total wire length, vegetation load, terrain, and power source (110-volt, 220-volt, or 12-volt battery).
- Tester — an electric-fence voltage meter, not a household multimeter.
If you haven’t picked a charger yet, this roundup of small electric fence kit options worth buying lays out matching energizers and coverage ratings side by side.
How Do You Install And Ground The Fence?
Build the physical fence first, drive the ground rod, and only then connect the energizer — with the power off. Grounding is where most first-time installs fail.
- Plan the route. Keep the fence clear of combustible material. Where it must run parallel to overhead power lines, offset it at least 30 feet and cap top wires at 6 feet.
- Set the posts. Use the supplied clips and supports, and keep the wire tight rather than sagging. Corners take the most tension.
- Run the conductor. Thread the galvanized wire through the clips and keep the hot wire isolated — away from posts, other wires, branches, and weeds.
- Drive the ground rod. Sink it deep near the energizer and clamp the ground lead to it.
- Mount the energizer. Parmak’s manual states 110–120-volt AC units must be mounted indoors in a clean, dry spot, with connections protected from weather.
- Wire the terminals. Ground lead to the rod, fence lead to the insulated hot wire — energizer off the whole time.
- Energize and test. Probe the wire at the farthest practical point with the fence meter. A reading well below the energizer’s rated output means a short, a bad splice, or weak grounding.
What Output Does The Energizer Actually Need?
Energizer choice comes down to one number — total energized wire length — plus load from grass, terrain, and the power source you can reach. A charger too small for the run reads weak at the far end no matter how clean the install.
| Setup Element | Target Figure | Why It Matters |
|---|---|---|
| Peak output voltage | 5,000 V minimum | USDA’s baseline for a high-power, low-impedance unit |
| Pulse duration | Under 0.0003 seconds | Keeps the shock brief and safe |
| Pulse rate | 35–65 per minute | Standard on/off cycle for livestock fencing |
| Ground rod per joule | 3 feet or more | USDA guidance; multiple rods spaced 6 feet apart |
| Power line offset | 30 feet minimum | When parallel routing is unavoidable |
| Top wire height | 6 feet maximum | Reduces contact risk near overhead lines |
| Wildlife-fence example | 0.7 joule, 6,000 V | Application-specific, not a universal rule |
Minnesota DNR guidance on energized fences confirms that matching the charger to the load — not buying the biggest unit on the shelf — is what keeps voltage steady across the run.
What Safety Rules Apply To An Energized Fence?
Treat every energized wire as live and warn anyone who might touch it. A gate or a switch, not a vault, is how people and pets cross.
- Never climb over, crawl under, or pass through an energized fence.
- Don’t bridge the positive and negative terminals by hand — use a fence-voltage meter.
- Post warning signs wherever children, visitors, or untrained people may meet the fence, and keep the wire visibly identifiable.
- Wear eye and hand protection: an overstretched wire can break and recoil.
- During drought or high wildfire risk, drop to a low-power setting if the unit has one, or switch it off.
Local electrical, livestock, wildlife, and zoning rules may add requirements beyond these US guidelines, and the energizer’s own manual always controls installation details for that model.
How Often Should You Check Voltage?
Test the fence after installation and then weekly — a voltage check takes about a minute and catches faults before an animal finds them. Inspect battery charge and terminals on solar or DC units at the same time, and repair corroded splices or damaged wire right away. Vegetation touching the hot wire is the most common cause of a sudden voltage drop.
Three passes tell you the fence is right: tight wire, a grounded energizer, and a strong reading at the farthest point.
Common Questions
Can I use a regular multimeter to test an electric fence?
No. A household multimeter isn’t built for the short, high-voltage pulses a fence energizer sends. Use a dedicated electric-fence voltage meter, which reads the pulse correctly and keeps your hands clear of the live wire.
Why is my fence voltage low at the far end?
Low readings usually trace back to four things: shorts from vegetation or sagging wire, poor splices, inadequate grounding, or an energizer undersized for the run. Walk the line, clear anything touching the wire, and check the ground rod connection before blaming the charger.
Does the Parmak kit include a fence charger?
No. The Parmak Electric Fence Kit is the physical fence package — wire, posts, ground rod, and clips. The charger is sold separately and must be matched to your fence length and power source.
Sources
- USDA. “Fence (FT) (382)” Supplies energizer output specs and ground-rod spacing guidance.
- Parmak. “Electric Fence Kit” Lists kit contents, price, and compatible fencers.
- Minnesota DNR. “Energized Fences” Covers matching energizers to fence load.