A Whirlpool Filter 1 replacement is a tool-free push-and-twist job: pull the old cartridge, seat the new one arrow-up, close the door until it snaps, then flush four gallons of water.
Skip the service call — the job runs about ten minutes. The only mistake that costs you is a cartridge seated crooked, which turns a two-minute swap into a puddle under the crisper drawer. Whether the filter sits behind a small door in the upper-right interior or in the base grille, the cartridge and motion are the same. The steps below follow Whirlpool’s published procedure, and the compatibility notes at the end are the part most people skip before ordering the wrong box.
Where Is the Filter 1 Housing on My Whirlpool Refrigerator?
Filter 1 lives in one of two spots: behind a small lift-up door in the upper-right corner of the refrigerator compartment, or in the base grille at the bottom front.
Check the top-right interior wall first; if there’s no cartridge door, crouch down and check the bottom grille. One of those covers the standard Whirlpool layouts. Once you’ve found the door, everything else is identical regardless of position.
How Do You Swap the Cartridge Step by Step?
Nine steps, no tools. Only two things matter: the arrow direction and aligning the notches before you push.
- Lift the filter door open.
- Pull the old cartridge straight out and discard it.
- Unpack the new filter and peel the protective coverings off the O-rings. Leave the O-rings in place — a worn or missing O-ring is a common cause of leaks after replacement.
- Slide the new cartridge in with its arrow pointing upward.
- Don’t force it. If it won’t seat easily, rotate the cartridge until its notches line up with the housing grooves, then push again.
- Close the filter door and press until it snaps. If it won’t shut fully, the cartridge isn’t locked in — pull it, realign, and reseat.
- Dispense four gallons of water through the dispenser to flush the new filter. This clears trapped air and carbon fines; the water may run cloudy or sputter at first.
That last step is the one people skip. Whirlpool specifies the four-gallon flush, and skipping it means your first few glasses taste off. You’ll know the cartridge seated correctly when the door clicks shut flush with the liner and the dispenser runs a steady stream after the flush instead of spitting air.
Which Cartridge Actually Fits, and What Does It Cost?
Whirlpool Refrigerator Water Filter 1 carries model number WHR1RXD1 and replaces W10295370A. The everydrop version, model EDR1RXD1, is the purple-capped one-pack that fits the same housing across Whirlpool, Maytag, KitchenAid, Amana, and JennAir refrigerators.
Match the package to the filter number and the refrigerator model before ordering — Whirlpool is explicit about checking both, and buying by number alone is how people end up with a cartridge that won’t seat. To compare options side by side, this roundup of tested Whirlpool Filter 1 cartridges lays out the fits and trade-offs.
The EDR1RXD1 is certified by NSF International under NSF/ANSI Standards 42, 53, and 401 for specified contaminant reductions.
| Replacement Detail | Specification |
|---|---|
| Filter 1 model number | WHR1RXD1 (replaces W10295370A) |
| everydrop equivalent | EDR1RXD1, purple cap |
| Change interval | Every 6 months or 200 gallons, whichever comes first |
| Certifications | NSF/ANSI 42, 53, and 401 |
| Flush volume after install | Four gallons |
| Tools required | None |
| Listed one-pack price | $41.99 (may change) |
What Does the Replace Filter Light Mean, and How Do You Reset It?
The indicator trips on either trigger: the rated water volume has passed through the cartridge, or six months have elapsed since installation. Whirlpool’s product help says to install a new filter as soon as the light comes on, then reset the status light.
Reset controls differ by model, and generic advice fails here. Whirlpool documents one bottom-freezer example that resets by holding Freezer and Drawer together for three seconds — but don’t assume that for every refrigerator. Check your manual for the model-specific reset before mashing buttons. Whirlpool’s water filter replacement guide covers the housing variations, and Whirlpool’s product help documentation spells out the indicator behavior.
Other failure modes: installing with the arrow reversed, leaving packaging on the O-rings, forcing a misaligned cartridge instead of rotating it, and running past six months or 200 gallons. Whirlpool also warns that instructions vary by make and model — your manual overrides any general walkthrough, including this one.
Common Questions
How long does the swap take?
About ten minutes for the physical replacement. The four-gallon flush adds a few minutes at the dispenser; run it into a pitcher or bucket if you’re watching water use. Seating the cartridge properly is the only step that ever adds time.
Can I use a Filter 1 cartridge in any Whirlpool fridge?
No. Filter 1 fits housings designed for WHR1RXD1 and EDR1RXD1, and Whirlpool warns that steps and cartridge types vary by model. Check your manual or the label inside the filter door before ordering, especially if your fridge came with a different filter number.
Why does my new filter make the water taste odd?
Usually trapped air and harmless carbon fines. Whirlpool’s four-gallon flush clears both. Run the dispenser until the stream is steady and clear, discard that water, and the taste settles. A persistent plastic taste after a full flush points to a cartridge that isn’t seated correctly.
Sources
- Whirlpool. “How to Replace Your Whirlpool Refrigerator Water Filter.” Source for the official replacement procedure, housing locations, and flush volume.
- Whirlpool Product Help. “Replace Filter – Refrigerator.” Source for indicator triggers and model-specific reset behavior.
- Whirlpool. “everydrop Refrigerator Ice & Water Filter 1 – Purple, EDR1RXD1.” Source for model numbers, certifications, replacement interval, and listed pricing.