Radiant floor panels work by warming a conductive surface that releases infrared heat upward, and the warmed floor also circulates air by convection.
A thermostat calls for heat, and within minutes the floor surface itself becomes the radiator. That single shift — heating surfaces instead of blowing air — explains why the same room can feel warm at a lower thermostat setting, and why the panels under your feet matter more than the furnace feeding them.
The pages below cover both panel families, how each one moves heat, and what real installations cost.
How Do Radiant Floor Panels Work?
Radiant floor panels heat a room by transferring energy from a warm floor surface to people, furniture, and surrounding surfaces through infrared radiation, while the warmed floor also drives natural air convection. The U.S. Department of Energy identifies radiant-air, electric, and hydronic floors as the three broad system types, and the panel designs in this guide fall into the hydronic and electric camps.
The chain of events inside a hydronic panel runs in a fixed order:
- The heat source — a boiler, heat pump, or water heater — warms water to the target temperature.
- A pump pushes that water through 1/2-inch PEX tubing seated in routed channels.
- A bonded aluminum layer spreads heat sideways across the panel so the floor warms evenly, not just along the tube.
- The floor finish radiates heat into the room and warms the air above it.
- Zone valves and thermostats regulate each loop independently.
Electric panels skip the water entirely. Resistance cable or conductive mats convert electricity directly into heat, which makes them straightforward for small areas but pricier to run where electricity rates are high.
Hydronic vs. Electric: Which Panel Type Fits?
Hydronic systems generally use less electricity and are typically the most cost-effective radiant option in heating-dominated climates, while electric floors suit small areas and additions where running water lines is impractical. The Department of Energy notes that high electricity prices can undercut electric floor economics unless the installation includes substantial thermal mass and favorable time-of-use rates.
| Feature | Hydronic Panels | Electric Panels |
|---|---|---|
| Heat carrier | Heated water in PEX tubing | Resistance cable or mats |
| Best application | Whole-home builds and remodels | Small areas, single rooms |
| Operating cost | Lower in cold climates | Higher where power is expensive |
| Zoning | Individual tubing loops | Separate mat circuits |
| Heat sources | Boiler, heat pump, water heater | Line voltage only |
| Floor buildup | 1 1/8 in (structural) or 13/16 in (retrofit) | Thin mat under finish |
| Wet or dry install | Both | Dry only |
Wet vs. Dry Installation: What’s the Difference?
Wet systems embed tubing in concrete or lightweight concrete, while dry systems place tubing between layers of wood, under a subfloor, or in routed panels. Wet pours add thermal mass that holds heat longer but adds height and curing time; dry panels go down fast and suit renovations where floor height is tight.
Warmboard’s two panel lines show how the split plays out in real products. Warmboard-S is a 1 1/8-inch, 4-by-8-foot tongue-and-groove panel built from 7-ply plywood with a bonded conductive aluminum surface, carrying an APA Exposure 1 rating and spanning up to 24 inches on center. Its spec sheet lists 3.1 pounds per square foot including panel, tubing, and water. Warmboard-R is a 13/16-inch, 2-by-4-foot panel on a high-grade OSB substrate, made for overlay work on existing subfloors or slabs. Both space their 1/2-inch PEX channels at 12 inches.
One detail worth flagging: Warmboard’s specification document describes its aluminum as 0.025-inch 1060 alloy, while the current product page states 1070. Both figures trace back to the manufacturer’s own materials, so treat the alloy number as source-specific rather than a typo to correct.
Minimum R-19 fiberglass batt insulation is recommended below the panels; foil-facing is not required.
How Much Do Radiant Floor Panels Cost?
No universal retail price exists, because cost depends on panel selection, home size, and installation complexity — Warmboard directs customers to submit floor plans for a preliminary design and personalized estimate. A 2025 third-party estimate, not a manufacturer price, puts installed hydronic radiant at $15–$30 per square foot without new flooring and $19–$45 with it, or roughly $30,000–$75,000 for an average whole-home system. Totals including new flooring run $38,000–$112,500.
Installation itself follows a predictable sequence: verify structural support and heat-load design, lay out straight and turning panels into continuous loops, seat the PEX, connect manifolds and the heat source, pressure-test before covering, install the approved finish, then commission each zone gradually. Skipping the pressure test is the expensive mistake — a leak found after the floor goes down means tearing it back up.
If you’re comparing panel brands before committing, our tested radiant floor panel roundup lays out the options side by side.
For the underlying mechanics, the Department of Energy’s radiant floor heat overview remains the clearest plain-language reference.
Common Questions
Can Radiant Panels Heat a Whole House?
Yes. Hydronic systems zone the home into separate tubing loops, each controlled by its own thermostat and zone valve, so bedrooms, living areas, and bathrooms heat independently. Whole-home installations typically pair panels with a boiler or heat pump sized to the building’s heat load, and the Department of Energy notes this setup is generally the most cost-effective radiant option in cold climates.
Do Radiant Floors Work Under Carpet?
Carpet and thick carpet padding insulate the floor surface and slow heat transfer upward, so most manufacturers publish finish restrictions. Tile, stone, and engineered wood conduct heat well. Always confirm the specific finish, adhesive, and underlayment against the panel maker’s requirements before installation, since an incompatible assembly can void coverage or underperform.
How Long Does a Radiant Floor Take to Warm Up?
Dry panel systems with low thermal mass respond fastest, often warming noticeably within an hour or two. Wet systems poured in concrete store more heat and take longer to reach temperature but hold it longer afterward. Gradual commissioning — raising the water temperature slowly over several days — protects the assembly and is standard practice on new pours.
Sources
- U.S. Department of Energy. “Radiant Floor Heat” Defines system types and the radiation-plus-convection heating mechanism.
- APA – The Engineered Wood Association. “Warmboard-S Evaluation/Span Information” Supports span, weight, and dimensional specifications.
- MLive. “As Ann Arbor aims to get off gas, some see promise in electric radiant floors” Context on electric radiant adoption and local energy considerations.