Most over-the-range microwaves vent through a 3¼ × 10-inch rectangular metal duct, and any round duct must be at least 6 inches in diameter.
Two over-the-range microwaves can wear 300 and 600 CFM badges and move nearly the same air once bolted to your cabinets. That gap is why CFM and duct size, elbows, and end caps all count toward the airflow your kitchen gets — and the duct usually counts first.
How Many CFM Does An Over The Range Microwave Need?
Most US over-the-range models land in the 280 to 400 CFM motor class, with 600 CFM units built for heavy searing and frying. Whirlpool’s spec sheets label those figures as open-air blower performance, measured with nothing attached to the outlet.
Bolted to a real duct, the numbers fall. The 300 CFM-class WMMF5930P measured 203 CFM on high with vertical ducting and 215 CFM with horizontal ducting at 0.1 inches of water gauge; at 0.25 inches it reads 171 and 175 CFM. The 400 CFM-class KMHC319L measured 286.6 vertical and 216.4 horizontal at 0.1 inches.
Current model classes run from the 300 CFM WMMS3130RW and WMMF5930P, through the 400 CFM KMHC319L and WML55011H, up to the 600 CFM KMML550R. A bigger badge on an undersized duct buys noise, not clearance. If you are still choosing the unit, this roundup of tested vent options for over-the-range microwaves pairs each size with the ductwork it needs.
Duct Size: 3¼ × 10 Or 6-Inch Round
The standard connection is a 3¼ × 10-inch rectangular metal duct. When round duct is required, the instructions call for a rectangular-to-round transition adapter and prohibit any duct smaller than 6 inches in diameter.
Metal is the only material approved for exterior venting. Whirlpool’s installation instructions also warn that a 6-inch round run is not an automatic swap for the rectangular outlet — the transition shape, its length, and the resistance it adds all change delivered airflow.
Every cited model ships with a damper, and that flap has to swing freely once the hood is up. Tape, framing, or a crooked cap that pins it shut will choke a correctly sized system.
| Duct Or Spec | Requirement | Why It Matters |
|---|---|---|
| Rectangular duct | 3¼ × 10 in., metal | Standard outlet on the cited Whirlpool models |
| Round duct | 6 in. minimum, transition adapter required | Smaller round duct is prohibited |
| Duct material | Metal only | Flexible and nonmetallic ducting is not approved |
| Total length | 140 equivalent feet maximum | Fittings and caps spend part of that budget |
| Cooktop clearance | 12⅛ in. minimum, 18⅛ in. recommended | Measured to the microwave’s bottom edge |
| Damper | Included, must open freely | A stuck damper kills airflow quietly |
| Recirculating mode | Charcoal filter, no outdoor exhaust | Leaves heat, smoke, and moisture indoors |
Duct Length, Clearances, And Install Order
Whirlpool caps total duct length at 140 equivalent feet whether the run is rectangular or 6-inch round. Straight sections count at measured length; every elbow, transition, wall cap, and roof cap adds the equivalent feet your manual or local code assigns.
Keep the run short and straight, and question any 90-degree elbow you can replace with a pair of 45s. Whirlpool lists 12⅛ inches minimum and 18⅛ inches recommended from the cooktop to the bottom of the microwave, and local building, electrical, and mechanical codes can demand more.
Recirculating setups are different: they filter grease and push air back into the room, so moisture, heat, smoke, and combustion by-products stay in the kitchen — that configuration needs the manufacturer’s charcoal filter and matching vent setup.
- Decide vertical, horizontal, or recirculating before anything gets cut.
- Match the cabinet or wall opening to the model’s outlet size and orientation.
- Run metal duct at 3¼ × 10 inches, or 6-inch round with a transition adapter.
- Total every section, fitting, and cap against the equivalent-length limit.
- Seat the damper so it swings free, then run the fan on high.
You are finished when a tissue clings to the filter grille and the damper flaps without rattle. The repeat offenders: treating motor-class CFM as installed airflow, squeezing in 4-inch round duct, skipping the transition, and letting a cap or taped seam block the damper.
Common Questions
Does A Higher CFM Rating Always Mean Better Venting?
No. The rating measures the blower with nothing attached. Elbows, transitions, and caps cut into that figure, so a 300 CFM model on a short straight run can outperform a 600 CFM model choked by a long, twisting one. Match the blower to a duct system it can actually feed.
Can I Use 4-Inch Round Duct?
No. Whirlpool’s instructions prohibit round duct smaller than 6 inches on its over-the-range models, and 4-inch duct chokes airflow enough to shorten motor life. If a 4-inch hole already exists, enlarge it to 6 inches or switch to a 3¼ × 10-inch rectangular run instead of adapting down.
How Much Space Goes Between The Cooktop And The Microwave?
Whirlpool lists 12⅛ inches as the minimum and 18⅛ inches as recommended from the cooking surface to the bottom of the microwave. Treat those as starting points, since your model’s manual and local building codes set the final number.
Sources
- Whirlpool. “Over-the-Range Microwave Oven Installation Instructions” Supports the 3¼ × 10-inch rectangular duct standard, the 6-inch round minimum, metal-only ducting, transition adapter, and 140 equivalent-foot limit.
- Whirlpool. “Ventilation Specification Sheet — WML55011H” Lists 400 CFM motor class, duct orientation, damper, and cooktop clearances.
- Whirlpool. “Ventilation Specification Sheet — WMMF5930P” Documents open-air blower ratings and the measured 203/215 CFM figures at 0.1 inches of water gauge.