How to Measure for Yard Trailer Tires (Sizing Guide) | Read the Placard First

Yard trailer tire size comes from the trailer’s tire placard, certification label, or the existing sidewall marking — not from a tape measure across the tread.

Guessing is how a yard trailer ends up with a tire that rubs the fender or fails under a load it was never rated for. The number is already printed on the trailer or the tire you’re replacing, and reading it takes about two minutes.

Where Does Yard Trailer Tire Size Come From?

The trailer’s own documentation is the authority: the tire-information placard, certification label, or owner’s manual. Federal tire labeling rules require applicable trailers to carry tire information that matches the vehicle, and that label outranks any generic online size chart.

Look for a sticker on the tongue, the frame rail near the coupler, or inside a fender well. It typically lists the recommended tire size, cold inflation pressure, and load limits — write down all three. If the sticker is weathered past reading, check the owner’s manual or manufacturer records.

How Do You Read the Sidewall Marking?

Copy the entire sidewall string exactly, including any prefix. A marking like ST205/75R15 carries every dimension you need.

  • ST — special trailer construction, what most small yard trailers specify.
  • 205 — nominal section width in millimeters, at the widest point of the sidewall.
  • 75 — aspect ratio; sidewall height is 75% of section width.
  • R — radial construction.
  • 15 — rim diameter in inches.
  • Load Range C, D, or E — the load and inflation tier the tire is built for.

Near the rim diameter you’ll find a load index stating the tire’s maximum carrying capacity. That matters as much as size, and it’s the one shoppers skip: a tire can bolt on perfectly and still be under-rated for a loaded trailer.

How Do You Measure When the Markings Are Gone?

Measure only as a fallback, and measure the right surfaces. Inflate to correct cold pressure, then run a tape across the widest point of the sidewall for section width — not the tread face, which reads narrower.

For the wheel, measure the bead-seat diameter where the tire seats, not the outer lip; expect a smaller number than the rim’s outside diameter. Confirm against a stamp on the rim when visible. Never pick a replacement from width and overall height alone — two tires with near-identical outside dimensions can carry different load ratings and sit differently under a fender.

What Else Has to Match Before You Buy?

Size is the entry ticket, not the whole purchase. The wheel has a rated width, diameter, and pressure limit the new tire must fit within, and a tire must never go onto a rim of a different diameter no matter how close it looks.

Confirm the tire clears the frame, fender, suspension, brakes, and the tire beside it through full suspension travel and while turning. Then check capacity: the combined rating of the installed tires must meet or exceed what the loaded axle carries. Weighing the loaded trailer settles that faster than any calculation.

Inflation follows the trailer manufacturer’s cold-pressure spec, not the maximum printed on the sidewall — that number is the pressure at which the tire reaches its rated load, not automatically the right operating pressure. Keep load range and load index matched or exceeded, and don’t mix sizes, constructions, or ratings across one axle. To compare specific models, this roundup of tested yard trailer tires pairs real options with their load ranges.

One more thirty-second check: bolt pattern and wheel load rating. A wheel rated below the tire’s capacity becomes the weak link, and no tire spec fixes that.

Which Mistakes Sink a Trailer Tire Purchase?

Most bad purchases trace to a few shortcuts. Tread-width measurement and the rim’s outside diameter are the biggest offenders, because both produce a number that looks plausible and fits nothing.

Other repeat offenders: choosing by appearance, treating load range as a substitute for the load index, and assuming a taller tire raises legal carrying capacity — it doesn’t, since GVWR and GAWR are set by the trailer, not the rubber. Replacing a single tire without matching size, construction, wear, and rating invites uneven loading. And any tire with cracks, bulges, or heavy wear gets replaced regardless of remaining tread.

For the underlying standards, NHTSA’s tire safety guidance covers load limits and labeling, and the FMVSS tire labeling rule explains what those placard markings must state.

Common Questions

Can I Put Passenger Tires on a Yard Trailer?

Only if the trailer manufacturer specifies them. Most small yard and utility trailers call for ST-rated tires, built for the higher sidewall loads trailers place on them. A passenger tire with matching dimensions can still fall short on load capacity and sidewall stiffness, so check the placard before substituting.

Is the Max Pressure on the Sidewall the Right Inflation?

Not automatically. The sidewall maximum is the pressure at which the tire carries its rated load, while the trailer’s placard states the pressure the manufacturer wants for that vehicle. Use the placard figure unless both makers approve an alternative, and always check when the tire is cold.

Does a Bigger Tire Raise My Trailer’s Weight Limit?

No. Gross vehicle weight rating and gross axle weight rating are set by the trailer’s structure and axles, not the tires. A larger tire may add clearance issues without adding legal capacity, so stay within the trailer’s rated limits regardless of tire size.

Sources

  • National Highway Traffic Safety Administration. “Tires” Supports load limit, inflation, and tire condition guidance.
  • National Highway Traffic Safety Administration. “FMVSS Tire Labeling” Supports placard and certification label requirements for trailers.
  • Goodyear. “Tire Size Calculator” Supports how sidewall size markings are decoded.

Scroll to Top