Measure each window’s width × height with a steel tape, decide inside versus outside mount first, and check the exact motorized model’s mounting-depth spec before ordering.
A motorized roller shade that arrives an eighth of an inch too wide is a dead shade sitting in a box. Electric shades cost real money, they are built to order, and most brands treat a wrong measurement as the buyer’s problem. The fix is a twenty-minute tape session done in the right order, which is what follows.
Two decisions come before the tape measure even leaves the drawer: inside mount or outside mount, and which exact model you are fitting. Both change the numbers you write down.
Inside Or Outside Mount: Which One Fits Your Window?
Inside mounts sit within the window recess for a recessed look; outside mounts overlap the opening or trim and block more light and gaps. Your recess depth decides whether inside mount is even possible once a motor is involved.
Measure recess depth from the front of the opening back to the glass at the spot where brackets will sit. Compare that number against the minimum and flush-mount depths listed for your exact motorized model — a shallow recess can handle a manual roller but not a shade with a battery tube behind it. If the recess is too tight, go outside mount.
Outside mount needs one more check before measuring: enough flat surface on the wall, trim, or header for the brackets to bite. Patchy trim means rethinking placement, not rethinking the order.
How Do You Measure A Window For An Inside-Mount Electric Shade?
Measure the recess at the bracket location, take width and height at three points each, and record the exact opening size with no deductions unless the manufacturer’s guide explicitly says to deduct. Blinds.com’s roller guide notes the factory makes its own deductions, so submitting a smaller number just makes the shade too small.
The step order that works:
- Width: measure across the top, center, and bottom of the recess to the nearest 1/8 inch. Most brackets mount at the top, so the top measurement usually governs — but if the opening narrows substantially toward the bottom, an outside mount is the safer call.
- Height: measure down the left, center, and right, then use the tallest height. Current roller guidance says to submit the full opening height and let the factory adjust.
- Depth: confirm the recess clears your model’s minimum mounting depth at the bracket line.
Watch for the trap buried in manufacturer paperwork: a separate roller-shade PDF instructs users to round width down to the nearest 1/8 inch, measure width about 1 1/4 inches below the top, and use the shortest height. That is the opposite of the first guide. Ordering rules are model-specific, so open the exact product’s guide and follow only that one.
Record every result as width first, height second — W × H — and keep notes for each window.
How Do You Measure For An Outside-Mount Shade?
Measure the desired finished coverage — not the window opening — then add overlap for privacy and light control. Outside-mount shades are typically built to the exact dimensions you submit, so deductions are on you, not the factory.
Blinds.com’s measuring instructions call for roughly 2–3 inches of overlap per side on roller shades when there is no trim; one PDF specifies a 3-inch overlap per side, 6 inches total, for stronger light blockage. For height, measure from the planned bracket or roller position down to where you want the fabric to stop. Guidance commonly allows about 3 inches above the opening for mounting hardware, with a separate guide recommending at least 2 1/2 inches at the top. Confirm which your model needs.
| Mount Type | Width Rule | Height Rule |
|---|---|---|
| Inside mount | Recess width at top; no deductions unless the product guide says so | Tallest of left, center, right |
| Inside mount (alternate guide) | Round down to nearest 1/8 in., measured 1 1/4 in. below top | Shortest height |
| Outside mount, no trim | Opening plus 2–3 in. per side | Bracket position to desired bottom |
| Outside mount, 6 in. total overlap | Opening plus 3 in. per side | Allow 2 1/2–3 in. above opening |
| Bay window, inside | Narrowest of top, middle, bottom per section | Tallest height per section |
| Bay window, outside | Overall width plus 3–4 in. | Add at least 2 in. |
| Angle-top window | Rectangular width, then angled portion | Tall side, short side, angle length |
One more number matters on outside mount: bracket-to-bracket width is not fabric width. A Zebra-shade guide states fabric arrives 1 3/8 inches narrower than the ordered width. That figure belongs to that product line, not to every motorized shade, so check your model’s spec sheet if the fabric must cover an exact opening. If you are still weighing which unit to buy, this roundup of tested electric window shades lists real-world coverage specs worth comparing before you commit.
What Changes For Bay And Angle-Top Windows?
Odd-shaped windows get measured section by section, because one recess measurement will not describe them. Blinds.com’s roller guide treats each bay section as its own window: measure top, middle, and bottom for width, take the narrowest for inside mount, and use the tallest height. Outside mount on a bay calls for adding 3–4 inches to overall width and at least 2 inches to height, subject to the product’s limits.
Angle-top and angle-bottom windows need three numbers plus the rectangular width: tall-side height, short-side height, and the length of the angle itself. A diagonal difference of 1/8 inch or more means the window is out of square, which usually points toward outside mount or a custom template from the manufacturer.
Before you order, run this check:
- Every window measured separately, even twins in the same room.
- Opening size, ordered size, bracket-to-bracket width, and fabric width kept as four distinct numbers.
- No deductions applied unless the exact product guide instructs it.
- Motor and battery clearance verified against the model’s flush-mount depth.
Get those four lines right and the shade shows up cut to your window. Full measurement procedures live in Blinds.com’s roller shade measurement guide, which is the document to keep open while the tape is out.
Common Questions
Should I subtract anything from an inside-mount measurement?
Only if the exact product’s guide tells you to. Blinds.com’s current roller guide says to submit the full opening size because the factory applies its own deductions, while a separate PDF rounds width down and uses the shortest height. Follow the single guide for the model you are ordering and ignore the rest.
Why does recess depth matter more for motorized shades?
A motorized shade carries a motor and often a battery tube behind the fabric, so it needs more depth than a manual roller. Measure from the front of the opening to the glass at the bracket location and compare it to the model’s minimum and flush-mount depths. If it falls short, switch to outside mount.
Do outside-mount shades come with extra fabric built in?
Usually not for coverage — they are built to the dimensions you submit, so the overlap has to be in your numbers. Fabric width can still differ from ordered width, though. One Zebra-shade guide lists fabric 1 3/8 inches narrower than ordered, so verify your model’s spec if exact coverage matters.
Sources
- Blinds.com. “Roller Shade Measurement Guide” Inside and outside mount procedures, bay and angle-top windows, and factory deduction rules.
- Blinds.com. “Measure Instructions — Roller and Solar Shades” Outside-mount overlap guidance and mounting depth requirements.
- Blinds.com. “Zebra Measuring Instructions” Bracket-to-bracket versus fabric width difference for that product line.