How to Measure Your Van for a Wheelchair Ramp | What To Tape Off

A wheelchair ramp fits only when the van’s real door opening, floor height, and outside landing zone are measured against the ramp maker’s published limits.

The measurement that sinks most van ramp purchases isn’t on the sales sheet. It’s the eight inches you didn’t know about — a door track, raised sill, or hinge bracket that keeps the ramp from sitting flat. Nominal body dimensions describe the van; the conversion describes what your wheelchair rolls through, and they rarely match.

Five measurements decide fit: door opening width and height, floor-to-ground loading height, outside deployment space, mobility device footprint, and every transition lip in between.

Which Measurements Actually Decide Fit?

Measure the usable opening, true loading height, and outside landing area — then compare against the conversion maker’s model-specific figures, not the van’s brochure. BraunAbility publishes opening height, width, ramp width, usable floor length, and ramp angle per conversion, and these change with model year and conversion type. Same van, different conversion, different answer.

How Do You Take the Door and Floor Measurements?

Open the loading door fully on level ground and measure the narrowest unobstructed width between trim, tracks, and handles — the ramp must pass through that gap, not the body opening. For height, measure from the entry sill to the lowest overhead obstruction, ignoring the step or bumper below.

Then measure loading height: straight down from the van floor surface where the ramp will rest to the ground it will sit on. Repeat with the van loaded as you normally drive it — suspension compresses with passengers, wheelchair, and cargo, and an inch of sag changes the ramp length you need.

  • Width: narrowest point between trim, door track, and handle.
  • Height: sill to lowest overhead obstruction.
  • Loading height: van floor to ground, level surface, loaded.
  • Transition: height and width of any sill, lip, hinge, or floor rail.

That last item is the quiet failure: a ramp can clear the opening by width yet refuse to seat because its end plate can’t lie flat over a raised track. Note every protrusion before you shop; when comparing vans or narrowing brands, a tested wheelchair ramp for van lineup shortlists what actually fits your numbers.

What Does the Ramp Manufacturer Need To See?

Loading height and your device’s footprint drive the ramp’s required length and load rating — and slope rules are not negotiable. Slope is rise divided by horizontal run; Exact requirements live in the ADA rules for ramps and curb ramps.

Converted minivans typically land in the 8.6- to 10-degree range, meaning the conversion builder already did the slope math for that doorway and floor height — which is why you measure the converted van, not the stock one. For the device itself, record the widest point, overall length, seated height, and combined weight of user plus chair or scooter.

Measurement Typical Figure Why It Matters
Door opening height 53–57 in Clearance under the overhead track
Door opening width 30.5–34.5 in Ramp must pass through the narrowest point
Ramp width 29.25–34 in Must exceed your device’s widest point
Usable floor length 89–98.5 in Room to park and secure the chair
Ramp angle 8.6–10 degrees Ride comfort and safe slope
Loading height Measure your van Sets required ramp length
Outside landing Measure your spot Ramp must touch down on stable ground

What Else Can Stop a Ramp From Working?

Deployment space is the skipped measurement. Ramp out from the door in the direction it will extend and check for curbs, sidewalk edges, parking lines, and turning room — a ramp that ends in a curb cut or a hole is unusable even if every other number matches. Brake the van on level ground while measuring.

Confirm the ramp’s attachment method matches your conversion. Ignore the van’s advertising dimensions entirely — measure the converted van in front of you, loaded, where you’ll actually park it.

Common Questions

Can I just measure the van’s sliding door and call it done?

No — a sliding door opening overstates usable clearance. With a ramp added, the door track, handle, and trim crowd the opening inward, and the ramp must fit through the tighter gap. Measure the narrowest unobstructed point with the door fully open, not the frame’s outer edge.

Why does loading height change after passengers get in?

Suspension compresses under passenger, wheelchair, and cargo weight, lowering the van floor closer to the ground. That shifts the ramp slope, so measure loading height with the van loaded as you normally drive it, not empty in the driveway.

Is a longer ramp always the safer choice?

Not always. A longer ramp softens the slope but needs more ground space outside the door and must land on continuous stable surface. Match ramp length to measured loading height and permitted slope, then confirm the deployed ramp still fits your parking spot.

Sources

Scroll to Top