A well house cover fits only when its usable interior beats the full outside envelope of your equipment — maximum width, length, and height, pipes included.
One skipped conduit run is enough to make a correctly measured cover useless. The measurement itself takes about ten minutes; the mistakes come from measuring the wrong objects, not from bad math. Get the full envelope on paper before you look at a single listing, and the sizing question answers itself.
What Do You Actually Measure For A Well House Cover?
Measure everything the cover must conceal, not just the well casing. Lowe’s advises matching the cover to the equipment dimensions and picking one slightly larger than the footprint.
- Well casing and pump head — the obvious center of the assembly.
- Pressure tank, which is often wider than the casing and sits off to one side.
- Exposed plumbing, valves, and irrigation manifolds sticking out past the tank.
- Pressure switch, wiring conduit, and the electrical disconnect, plus any backflow device.
Walk the whole perimeter with a notepad. Side-mounted fittings are the single most common source of a cover that arrives too small.
How To Measure The Envelope In Four Steps
Record three numbers — maximum width, maximum length, and total height — at the widest point of each, fittings included.
- Width and length. Run the tape past the outermost pipe or valve on each axis, not along the casing. Write both in inches, oriented the same way the product listing shows them.
- Height. Measure from the ground or slab to the highest component. On uneven ground, measure from the lowest point so the cover still clears.
- Clearance. Choose a cover with interior space larger than your envelope. No universal allowance applies across brands, so the manufacturer’s dimensional drawing or installation instructions control.
- Access and footprint. The cover has to lift off for pressure adjustments, repairs, and electrical work — Lowe’s specifically calls for easy removal. Confirm it sits on stable ground and clears doors, fencing, drainage, mowing paths, and vehicles.
The success check is simple: your three measurements, plus the drawing’s interior dimensions, leave a visible margin on every side.
Well House Cover Sizes And Prices: What’s On Shelves
US retail listings scale from about 20 inches to over 60 inches, and price tracks size rather than shape.
| Cover Size Class | Example Listing | Approx. Price |
|---|---|---|
| Small (24 × 20 × 24 in.) | Dekorra 115-FS, gray fake rock | $114.62 |
| Compact flat (31 × 27 × 6 in.) | Dekorra 108-FS | $99.98 |
| Medium (27 × 21 × 25 in.) | Dekorra 102-RB | $146.00 |
| Square (36 × 36 × 9 in.) | Dekorra 112-FS | $154.00 |
| Long low (48 × 20 × 30 in.) | Dekorra 116-RB | $360.01 |
| Large rock (45 × 36 × 42 in.) | Dekorra 123-SS, for pressure tanks and backflow | $438.90 |
| Extra-large (63 × 48 × 61 in.) | Dekorra 114-FS | $849.00 |
Treat listed prices as snapshots — they shift with color, stock, and location. Lowe’s sizing guidance is the place to cross-check how a category interprets fit before you commit.
Why Do Covers Arrive Too Small?
Most returns trace back to one of a few measurement habits, and each is easy to avoid.
- Measuring only the casing. The pressure tank and side fittings usually set the real width.
- Trusting outside dimensions. A rock-shaped cover’s sloped shell eats interior space — a 45-inch-wide rock may not swallow a 44-inch assembly.
- Skimping on height. A tall pressure switch or valve handle silently adds inches.
- Burying or bolting the cover shut. It has to stay removable for service.
These covers also conceal and protect — they are not rated as structural buildings, electrical enclosures, or freeze-proof systems. Never let one block required ventilation, drainage, pressure-relief discharge, or the electrical disconnect. Local plumbing, electrical, and wellhead rules still apply, and the manufacturer’s installation sheet overrides any general advice. Once your envelope is on paper, compare the models that clear it in our tested well house cover roundup.
Common Questions
Should I measure in inches or feet?
Use inches. Retail listings, dimensional drawings, and model specs for well covers are published in inches, and converting invites rounding errors. Keep all three numbers — width, length, height — in the same unit and the same axis orientation the listing uses, so a direct comparison takes seconds.
Does a bigger cover cause problems?
Oversizing is safer than undersizing, with one limit: the cover must still sit fully on stable ground and stay removable. Excess size can put the shell over drainage paths, block access, or catch wind where it isn’t anchored per the manufacturer’s instructions. Measure the footprint, not just the equipment.
Can I cover a pressure tank and backflow assembly together?
Often yes, if one cover’s interior clears both. Some large artificial-rock models are marketed specifically for well pressure tanks and backflow assemblies. Measure the combined envelope — both units plus connecting pipe — and confirm access for testing and service before choosing a single enclosure.
Sources
- Lowe’s. “Well Pump Covers” Category guidance and typical pricing for well pump covers.
- Lowe’s. “Well Pump Covers — Valves” Sizing and easy-removal selection guidance.
- Home Depot. “Well Pump Covers” Dekorra model dimensions and listed prices.