Measure the furniture as it will sit under the cover — including cushions, arms, and backrests — then record maximum length, depth, and height in inches and compare all three to the cover’s size chart.
For the full breakdown, see our best Outdoor Furniture Covers guide.
Covers are cut to three dimensions, not one, so a footprint-only measurement is the fastest way to buy the wrong size.
Should You Measure Furniture Before Or After Adding Cushions?
Measure in the exact setup the furniture will be stored in, cushions and all. A cover has to clear whatever stays on the piece, so anything permanent belongs in the numbers.
Arrange chairs, grouped pieces, and umbrellas the way they will sit under the cover. Leave attached cushion backs, fixed hardware, handles, and decorative tops in place — those are the points that push a cover from a snug fit to an unusable one. Lowe’s measurement guide makes the same point plainly: if the cushion stays out on the patio, it counts.
Two quick calls before you start:
- If the cushions come inside every night, measure without them.
- If they live outside under the cover, they are part of the piece now.
How Do You Take Length, Depth, And Height?
Take three straight-line measurements at the widest point or the highest point — never around a curve and never at the seat. Each one goes on the pad separately.
Length or width: run the tape across the widest left-to-right span, edge to outermost edge. On a sofa or chair, that means from the outside of one armrest to the outside of the other. On a table, use whichever is greater — the tabletop or the base — because a flared pedestal can overhang the top.
Depth: measure front to back at the deepest point. Attached pillow backs, curved frames, and chaise leg extensions all count toward that number.
Height: measure from the ground to the highest point. That is usually the top of a backrest or tabletop, but a raised cushion or a finial can sit higher. Do not measure from the seat upward — a cover has to reach the floor.
Write the three numbers down in inches as you go. Kovi Fabrics’ measuring guide recommends rechecking each figure against the manufacturer’s diagram before ordering, since a cover can be wide enough and still too shallow.
Outdoor Furniture Measuring: What Decides The Fit On Odd Shapes
Round, rectangular, chaise, and grouped pieces each need a different treatment, and the shape dictates which dimension matters most.
Round tables take one measurement: the widest straight-across distance through the center, which is the diameter. Rectangular tables need the long and short sides recorded separately. A chaise needs its full length measured out flat, including the leg section when it is extended — a folded chaise measurement will not fit a cover made for the unfolded shape. A sectional or a table-and-chair set that shares one cover gets measured as the whole arrangement, not piece by piece.
Allowance is the other variable. A cover cut too tight traps moisture against the frame and strains its seams in wind; one that is far too loose catches air and flaps. Split the difference with the size chart’s own numbers.
What Are The Most Common Measuring Mistakes?
Most wrong-size orders trace back to a short list of habits, and each one is easy to break.
- Measuring the frame and skipping the cushions, arms, or attached extensions.
- Measuring the seat instead of the widest outside points.
- Running the tape around a curve instead of straight across the outermost edges.
- Checking length and width but not height, or missing a second height point in the diagram.
- Trusting the catalog dimensions instead of the actual stored setup.
- Rounding down when the measurement lands between two sizes.
Round up, always. A cover a size larger is a minor annoyance; one that will not close over the arms is a return. If you are comparing styles as you go, this roundup of tested outdoor furniture covers pairs well with your numbers, since sizing varies by brand. Fire tables need their raised burner lid included in the height, and the burner should be off and fully cool before the cover goes on.
Common Questions
Can I use the manufacturer dimensions instead of measuring?
Only as a starting point. Factory specs describe the piece as it shipped, not as it sits now with cushions, a topper, or a folded leg extension. Measuring the actual stored configuration takes a few minutes and catches every change.
What if the three dimensions land in different size tiers?
Buy to the largest one. A cover must clear every dimension at once, so the tallest, deepest, or widest figure sets the minimum size. Check the product diagram to confirm that size still fastens properly.
Do I measure a table with the umbrella in it?
Only if the umbrella stays up under the cover. If the pole and canopy come out, remove them first and measure the bare table plus any base collar that stays mounted.
Sources
- Lowe’s. “How to Measure Outdoor Furniture for a Cover” Source for the measuring procedure, the 1–2 inch allowance, and common mistakes.
- Kovi Fabrics. “How to Measure a Furniture Cover” Source for shape handling, rechecking against product diagrams, and fit guidance.