How to Measure Your Head for an XXL Bike Helmet | Tape, Fit, Check

Measure around the head about 1 inch above the eyebrows and just above the ears, then match that circumference to the specific helmet model’s size chart — never to a generic XXL label.

Head circumference decides whether a bike helmet fits, and the taping takes about a minute. A tape stretched across the widest part of the skull, or held loose and tilted, sends you to the wrong size. Bell Helmets gives a precise procedure, and following it exactly separates a helmet that disappears on your head from one you return twice.

There is a second half most guides skip: “XXL” is not a shared standard between brands. What you do with the measurement matters as much as taking it.

How Do You Measure Head Circumference For A Helmet?

Wrap a flexible tape around your head roughly 1 inch (2.5 cm) above the eyebrows and just above the ears, keep it level and snug but not tight, and take the reading twice — using the larger of the two.

No tape measure? A piece of string works: wrap it the same way, mark where it meets, then lay it flat against a ruler. The string trick adds a small error margin, so pull it snug without compressing the skin.

  • Height of the tape. About 1 inch above the eyebrows, passing just above the ears. Not across the forehead ridge, not around the widest bulge of the skull.
  • Level all the way around. A tape that dips at the back reads short.
  • Snug, not tight. Contact, not pressure lines on the skin.
  • Two passes, larger reading. Bell recommends measuring twice and using the bigger number.

Record the result in both inches and centimeters — some size charts use one, some the other.

What Does XXL Mean On A Bike Helmet?

XXL is not one fixed circumference; each manufacturer defines it in its own size chart, and the range differs by model.

Bell’s cycling catalog lists products under combined ranges such as XL/XXL and points buyers to the individual product page for that model’s chart rather than a universal XXL figure. Shell shape, padding, and retention dials change how a given circumference lands inside a shell: a helmet with a wide adjustment range may cover a head that a fixed-padding model of the same nominal size will not.

The label is the last step, not the first. Circumference first, model chart second, XXL third.

How Should An XXL Helmet Actually Fit?

A correctly sized helmet sits snug enough that forehead skin shifts slightly when you rock it side to side, with no pressure headache and no loose wobble.

Fasten the chin strap snugly, then run two checks Bell describes:

  1. The side-to-side twist. Some forehead movement is correct. Gripping pressure or a sliding shell is not.
  2. The roll test. Try rolling the helmet forward and backward. If it rolls completely off, forward far enough to block your vision, or backward far enough to bare your forehead, it is too large — regardless of the tag.

Half-shell and full-face helmets both get the roll test; the standard is the same.

Sizing up is the usual advice between two sizes, and Bell endorses the larger option for comfort — but only within a model whose adjustment range can still snug it down. If the roll test fails after sizing up, that model is wrong for your head shape. Once the measurement is reliable, this tested roundup of XXL bike helmets lists options with their size charts side by side.

What Are The Most Common Measuring Mistakes?

Most bad fits trace to a handful of repeatable errors, each caught by a second measurement.

  • Taping the widest part of the head instead of the 1-inch-above-the-eyebrows line, which inflates the reading.
  • A loose, tight, or angled tape. Level and snug is the standard.
  • One measurement. Bell specifies two, using the larger.
  • Substituting a hat size or another helmet’s size for the model’s circumference chart. Bell notes hat size is a rough guide at best; the measured circumference must meet the product chart.
  • Treating XXL as standardized across brands and models. It is not.
  • Buying on comfort alone without the twist and roll tests.

Before ordering, confirm on the product page that the model carries the certification and intended use you need and is available in your region — availability, certification, color, and pricing vary by market.

Measured once, checked against the right chart, and verified with the roll test, an XXL bike helmet stops being a gamble. Take the number twice, trust the model’s chart over the label, and let the twist test settle it.

Common Questions

Should I measure my head in inches or centimeters?

Use whichever unit the helmet’s size chart uses, and record both if you can. Converting afterward adds a rounding step that can nudge you off a size boundary; reading the tape directly in the chart’s unit removes that risk.

Can I use a hat size to pick a bike helmet?

Hat size is a rough starting point at best. Bell notes it can help, but the measured circumference should still be matched to the specific model’s chart. Hat sizing varies by brand and often rounds to the nearest fraction, while helmets fit exact centimeter ranges.

What if my measurement falls between two sizes?

Choose the larger size, provided the model’s adjustment system can still tighten it down securely. Then run the twist and roll tests with the chin strap fastened. If the larger helmet rolls off or exposes your forehead, the shell shape does not match your head and a different model is the better answer.

Sources

  • Bell Helmets. “How to Fit Your Bike Helmet” Source for the measurement procedure, two-reading rule, and the twist and roll fit checks.
  • Bell Helmets. “Size Chart” Directs buyers to model-specific charts rather than a universal XXL circumference.

Scroll to Top