A wall-mounted electric heater runs its supply through the thermostat first, and every connection must follow the model’s manual and local codes.
Three checks trip up most of these jobs, and none of them is the heater: supply voltage, thermostat load rating, and thermostat placement. The eight steps below walk through how to install a wall mounted electric heater with thermostat control inline, from the breaker to the first heating cycle.
Settle the labor question before buying anything. Cadet’s manuals state that permanent wiring must comply with national and local electrical codes and, where the code requires it, be performed by a certified or qualified electrician. New 240-volt circuit work is commonly restricted to licensed electricians in the US, so budget for one on the run from the panel even when you handle the mounting yourself.
What Has To Match Before You Cut The Wall?
Voltage and load ratings must line up across the breaker, thermostat, and heater before anything goes into the wall. A thermostat that looks close on paper is not close enough — check voltage, maximum load, heater type, conductor, and box requirements in both manuals.
- Nameplate voltage.
- Thermostat load rating. Heater wattage and amperage must fall inside the thermostat’s published range, not near the top of it.
- Pole count.
- Conductors and box. Cadet’s thermostat instructions call for copper conductors only and a certified electrical box.
- Models that refuse a wall thermostat. The Cadet CB, Energy Plus, and RCP series are built around their specified onboard controls and should not get a wall unit.
- Fan-forced heaters need a thermostat. Cadet recommends electronic wall thermostats over mechanical ones for comfort and energy savings.
If the room still needs a heater, our tested wall-mounted heater and thermostat picks narrow the shortlist to units whose manuals actually document a wall-thermostat hookup.
| What To Check | Where It’s Printed | What Fails If Skipped |
|---|---|---|
| Supply voltage (120 V or 240 V) | Heater nameplate and breaker label | Underheating, or a burned-out element |
| Wattage and amperage | Heater nameplate | Thermostat contacts weld shut |
| Thermostat maximum load | Thermostat instruction sheet | Early thermostat failure |
| Heater series restrictions | Model owner’s guide | Onboard and wall controls fight each other |
| Wall surface type | Model owner’s guide | |
| Floor and combustible clearances | Model owner’s guide | Burn risk and blocked airflow |
Wiring An Electric Wall Heater With A Thermostat: What The Manual Requires
Supply cable runs from the breaker to the thermostat location, then from the thermostat to the heater, with the heater’s own leads landed last. The breaker stays off through every step until the covers are back on.
The Cadet wall heater installation manual carries the exact connector, cable, and clearance figures that shift from model to model.
- Confirm the model and the spot. Match the heater’s voltage rating to the supply, keep the unit off vinyl-covered walls, and leave the airflow path clear of furniture and décor.
- Shut off the circuit at the breaker or fuse before opening any electrical box.
- Cut the opening beside a stud, run the supply cable, and install the wall can or mounting hardware. Cutout and clearance figures come from that model’s guide — one Cadet manual specifies horizontal mounting and a 6-foot minimum from the floor, which is that product’s rule and not a universal one.
- Pull cable from the breaker to the thermostat, then on to the heater. Leave at least 6 inches of wire at the heater box, as one Cadet guide specifies, and use approved connectors and cable clamps.
- Wire the thermostat. On the documented Cadet unit at 240 volts, black L1 goes to the first live supply conductor and red L2 to the second; at 120 volts, red L2 goes to neutral. Load leads land on the heater conductors. Never carry that color scheme to a different thermostat without reading its own diagram.
- Mount the wallplate on the certified box, set any configuration switches, refit the faceplate, and tighten the retaining screw.
- Seat the heater assembly in the wall can, fit the grille, and line up the thermostat shaft and knob if the heater has a built-in control.
- Restore power only after every cover and grille is secured.
Where Should The Thermostat Sit?
Cadet warns against the stud bay directly above a fan heater because rising residual heat skews the reading — a different bay or an adjacent inside wall works better.
Testing runs in one direction only. With covers on and power restored, turn a mechanical thermostat fully up and let the room reach temperature. Then dial it down slowly until it clicks off. The heater should cycle around that setting.
- Two heaters on one circuit need the extra wiring, a wall thermostat, and a circuit, breaker, and code that can carry the combined load — Cadet permits it only under those conditions.
- A thermostat is not a safety device where a critical temperature must hold.
- One Cadet model’s post-install check is a 30-minute run at the highest setting; follow your own manual rather than borrowing that instruction.
Two numbers decide the whole job: the heater’s nameplate voltage and the thermostat’s rated load. Get those correct, keep the thermostat out of the heater’s rising heat, and the rest is ordinary box work.
Common Questions
Can The Thermostat Go Directly Above The Heater?
No. Cadet singles out the stud bay directly above a fan heater as a bad spot, because residual heat rises into the device and throws off the reading, which makes the heater short-cycle. Use a different bay on the same wall or move to an adjacent inside wall. Keep it clear of drafts, direct sun, appliances, and shelving too.
Does Every Wall Heater Need A Separate Thermostat?
Not every model. Fan-forced heaters do need a thermostat of some kind, either built-in or wall-mounted, but the Cadet CB, Energy Plus, and RCP series are designed around their specified onboard controls and should not be paired with a wall unit. Check the owner’s guide for your exact model before buying a thermostat separately.
Can Two Heaters Share One Thermostat And Circuit?
Only when the wiring, breaker, thermostat rating, and local codes all support the combined load. Cadet allows multiple heaters on a shared circuit with the required additional wiring and a wall thermostat, subject to code. Adding a second heater to an existing circuit without recalculating the load is how tripped breakers start.
Sources
- Cadet. “Wall Heater Installation Manual (67065)” Source for the wiring sequence, conductor and box requirements, and model-specific clearances.
- Cadet. “Wall Heater Installation Support” Covers mounting options and the electrician and code requirements for permanent wiring.
- Cadet. “Thermostat Placement” Supports the five-foot mounting height and the warning about heat above the heater.