How to Install Police Lights for Car | Wiring, Mounting, and Safety Setup

Red and blue police lights are reserved for authorized emergency vehicles; private cars can usually run amber or white warning lights instead.

One wrong color can turn a weekend wiring project into a misdemeanor. The electrical work — fuse, relay, switch, ground — is identical whether you’re mounting a volunteer firefighter’s dash strobe or a tow truck’s amber bar. What follows covers the wiring order, the mounting checks, and the aiming that keeps a legal install legal.

Which Lights Can You Legally Install On A Private Car?

Your state statute is the one that counts, and the gaps between states are wide enough to settle before you buy a single lamp.

Read your state vehicle code’s section on emergency lights first. Ten minutes there decides the rest of the build.

Light Color Who Typically Runs It Private-Vehicle Rule
Amber Tow trucks, plows, utility and construction crews Widely allowed for hazard and work use
White Every driver, as auxiliary or work lighting Allowed within aiming and mounting-height rules
Red Fire, EMS, some volunteer departments Restricted; permit required where offered
Blue Police, and volunteer fire in some states Restricted; permit required where offered
Red and blue together Emergency vehicles only Illegal on private cars in every state
Purple or green Funeral processions, some EMS services Varies by state; confirm before buying

Federal rules cover the hardware, separate from the color question. Federal Motor Vehicle Safety Standard 108 sets the requirements for lamps and reflective devices, including replacement lighting equipment sold for road use.

Wiring Police-Style Lights: Power, Relay, And Switch Order

Wire in a fixed order — fused power, relay, switch, then ground at bare metal — so the switch carries only the relay’s small trigger current. A short anywhere downstream then blows a fuse instead of melting a harness.

  1. Lay the run before you drill. Set the bar in place, mark each wire entry, and look behind every panel for factory harnesses, fuel lines, and side-airbag canisters. No wire passes through an airbag pillar.
  2. Tap a fused circuit. For a bar drawing more than roughly 10 amps, run 12- or 14-gauge wire to the battery with an inline fuse within a foot of the positive terminal.
  3. Wire the relay. Terminal 30 to fused power, 85 to ground, 86 to the switch, 87 to the lights.
  4. Seat the switch. Drill a hole just under the switch body’s diameter, deburr the edge, and test-fit so the terminals clear the dash structure behind the panel.
  5. Ground to bare steel. Sand to shiny metal, crimp a ring terminal, add a star washer, and coat the joint in dielectric grease.
  6. Seal every pass-through. Rubber grommets at each hole, split loom over the full length, and silicone at the firewall entry.

Flip the switch: the relay should click once, the pilot light should come on, and the strobe should step through its patterns in order.

Mounting, Aiming, And The Checks Before First Use

Bracket choice decides whether the install survives a car wash, and aim decides whether the pattern reads as a warning or a glare bomb. Both get settled in the driveway, before the first drive.

Permanent roof brackets bolt through the panel into a backing plate, with silicone under the foot. Suction dash and deck lights are the least invasive option for interior strobes. If you’re still choosing hardware, our tested police lights for car roundup compares mount types and draw ratings side by side.

Aim white work lamps downward and outward so the hot spot lands on pavement, not in a mirror. Amber heads should throw sideways and slightly down; a flat-angled bar flashes straight into oncoming windshields. Set the pattern, walk 50 feet back, and judge the glare from a driver’s eye height.

Run this sequence once the wiring is finished:

  1. Check your state’s color rule against the statute or DMV page, and print it.
  2. Carry the department authorization letter if you run red or blue under a volunteer permit.
  3. Test with the engine running and headlights on, watching the dash for flicker.
  4. Re-torque the brackets and re-seal the roof entry after the first week.
  5. Keep the switch off while moving unless your permit specifically covers it.

Common Questions

Do LED Warning Lights Still Need A Relay?

Most do. A relay keeps high current out of the switch, and a roof bar with several LED heads can still pull 15 to 25 amps even though LEDs are efficient. Small dash strobes drawing under 5 amps can run straight off a switch rated for that load.

Can You Power Police-Style Lights From The Cigarette Lighter?

A full roof bar will blow that fuse or overheat the plug. Use a dedicated fused run for anything larger than one dash unit.

Are Magnetic Light Mounts Safe At Highway Speed?

Rarely. Rubber-footed magnets hold well around town, but wind load at 60 mph can slide a bar and let the cable chafe against paint. Magnetic mounts suit temporary use, and the bar should come off before a car wash or a highway trip.

Sources

Scroll to Top