How to Measure Wheel Size and Bolt Pattern for 20 Inch Wheels? | What the Numbers Mean

A 20-inch wheel is measured at the bead seats — the inner ledges the tire locks onto — not across the outer flange lips, and bolt pattern is recorded as lug-hole count times bolt-circle diameter.

The wheel already bolted to your car can pass for a 22-inch if you measure the lazy way. Run a tape across the outermost lips and you add roughly an inch of flange on each side — enough to order the wrong set of rims and eat return shipping. The measurement everyone quotes is a different one, and it takes ten minutes with a tape measure to get right.

Here is what decides the number: where you place the tape, and how you read the marking stamped on the wheel. Everything below assumes the tire is off, because measuring through a mounted tire gives you guesses.

What Does the “20” In a 20-Inch Wheel Actually Measure?

The 20 in a 20-inch wheel is the nominal bead-seat diameter — the distance across the wheel where the tire’s beads sit — and it is not the wheel’s outside diameter.

Two habits wreck this measurement. The first is measuring flange edge to flange edge, which reads large and produces a wheel that will not match your tire. The second is trusting a tire sidewall. A size like 245/40R20 tells you the tire belongs on a 20-inch rim, and nothing more — it says nothing about wheel width, offset, center bore, or bolt pattern.

Dismount the tire or pull the wheel off the car before you start. A steel tape or calipers works; clamp the tape so it stays straight across the hub opening. Then measure from one bead seat straight across to the seat on the opposite side, and measure width between the inner bead seats rather than the outer lips.

Diameter alone settles very little. Write down offset, center-bore diameter, and load rating while the wheel is off the car, because a 20-inch wheel with the right bolt pattern still fails to fit for any of those reasons.

How Do You Measure Bolt Pattern Without Getting It Wrong?

Bolt pattern, also called PCD, pairs the number of lug holes with the diameter of an imaginary circle drawn through their centers — 4×100 and 5×114.3 are two examples. Count the holes first, then measure the circle.

The easy case is any wheel with four, six, or eight lugs. Measure from the center of one hole straight across to the center of the hole directly opposite. That distance is your bolt-circle diameter, so 4.5 inches on a four-lug wheel reads 4×4.5 in.

Five-lug wheels are the problem. There is no hole sitting directly across from another, so the tape measure runs from the center of one hole to the imaginary outer edge of the circle formed by the two opposing holes. That yields an estimate, and closely spaced five-lug patterns blur together at that scale — 5×112 and 5×114.3 are three-tenths of a millimeter apart, far below what a tape resolves. A dedicated bolt-pattern gauge does this properly, and Tire Rack keeps gauges for the common inch and metric patterns, including 5×100, 5×108, 5×112, 5×114.3, 5×115, 5×120, 5×127, 5×130, 5×135, and 5×150.

Watch the unit conversion. 114.3 mm is commonly written as 4.5 inches, but the manufacturer’s exact figure is the one to use.

Measurement Where the Tape Goes Common Slip
Wheel diameter Bead seat to opposite bead seat Measuring flange lip to flange lip
Wheel width Inner bead seat to inner bead seat Measuring across the outer flanges
Bolt pattern, 4/6/8 lugs Hole center to opposite hole center Assuming lug count equals pattern
Bolt pattern, 5 lugs Hole center to outer edge of opposing circle Trusting a tape estimate over a gauge
Center bore Across the hub opening Skipping it because the lugs lined up
Lug thread Seat type, diameter, and pitch on the hardware Reusing nuts from a different seat style
Brake clearance Wheel to caliper and rotor gap, test-fitted Checking spokes by eye before mounting

Once diameter and pattern are written down, the remaining numbers decide whether the wheel actually goes on. If you would rather start from a shortlist of tested options, this roundup of the best 20-inch wheels for trucks pairs real fitments with the specs each wheel ships with.

What Else Has to Match Before a 20-Inch Wheel Fits?

Matching diameter and bolt pattern is only the entry ticket — center bore, offset, brake clearance, lug hardware, and load rating each veto a wheel on their own. A rim that bolts up can still rub a strut, shear a stud, or overload an axle.

Center bore comes first. A wheel with a larger bore than your hub needs an accurately sized centering ring; a smaller bore simply will not seat over the hub. Offset is next, and it governs tire, suspension, fender, and steering clearance — the wrong figure rubs or shifts handling geometry.

Brake clearance needs a physical test fit.

Lug hardware carries its own rules. Confirm seat type, thread diameter, and thread pitch, then start every nut by hand — it should thread on without force. Final torque follows the vehicle manufacturer’s spec, applied with a calibrated wrench in the crisscross sequence after hand-tightening. The full walkthrough lives in Tire Rack’s bolt pattern guide.

Three more checks round it out. Confirm the wheel meets or beats the vehicle’s gross axle weight rating. Check clearance on struts, control arms, rotors, the hub, and locating pins. If the car runs direct TPMS sensors inside the wheel, the new rim has to accept the sensor and may need a relearn.

Two assumptions cause most of the failures. Different five-lug patterns are not interchangeable, and a wheel that bolts on is not a wheel that is safe — a tape-measured five-lug guess is never a substitute for a gauge or an exact fitment check when one is available.

Test-fit before driving. If the wheel touches brakes, suspension, or bodywork, stop and take it back off.

Common Questions

Can I measure the bolt pattern with the wheel still on the car?

You can count lug holes on the car, but bolt-circle diameter is unreliable with the wheel mounted — the hub and brake hardware block a straight tape path. Pull the wheel, or use a bolt-pattern gauge pressed against the lug holes, which works without a clear run across the hub face.

Is a 20-inch tire the same as a 20-inch wheel?

No. The R20 in a tire size like 245/40R20 means the tire is built for a 20-inch rim diameter. It says nothing about wheel width, offset, center bore, or bolt pattern, so a tire that reads 20 inches can still sit on a rim that will not fit your vehicle.

Why is my 5×114.3 wheel not fitting my 5×112 hub?

Those patterns differ by 2.3 mm of bolt-circle diameter, which is enough to stop the studs from lining up. Lug count alone is not a match — 5×112 and 5×114.3 share the same five holes but not the same circle, and forcing hardware onto a mismatched pattern damages threads.

Sources

Scroll to Top