Panoramic glass cases fit only when three numbers line up: motherboard form factor, installed card length, and CPU cooler height.
Two builders order the same white fish tank case, and only one graphics card fits. The glass is identical; the builds are not. Six measurements settle how to choose a white fish tank PC case that fits your motherboard and GPU, and none of them is the one on the product photo.
The order below runs board first, card second, cooling and power last, because each step narrows the next.
Match The Motherboard Form Factor Before Anything Else
Motherboard form factor comes first because it decides what the case must physically accept: ATX boards are larger than Micro-ATX, and Mini-ITX is smaller than both.
Read the form factor off the board’s specification page or the retail box. A case that lists ATX usually lists Micro-ATX and Mini-ITX too, but check the exact model rather than assuming downward support. E-ATX is where the lists get slippery — Lian Li supports E-ATX on the O11 Vision only when the board is under 280 mm wide, so a wide workstation board can miss on a case that advertises the size.
Back-connect boards add a second check. The O11 Vision Compact explicitly lists back-connect ATX; the standard O11 Vision lists conventional E-ATX, ATX, Micro-ATX, and Mini-ITX. If your cables exit behind the socket, you need the rear cutouts, not just a form-factor line on the box.
White Fish Tank Cases: The Limits That Decide The Fit
Every fit question reduces to a published limit, and glass chassis publish four: card length, cooler height, power-supply length, and radiator size.
Two cases with the same look can differ by more than 20 mm on the numbers that matter. Lian Li’s O11 Vision specification page lists 430 mm of GPU clearance, 174 mm of cooler height, and ATX power supplies under 232 mm. The O11 Vision Compact trims each figure to sit in a smaller footprint.
| Spec | O11 Vision (O11VW White) | O11 Vision Compact (O11VPW White) |
|---|---|---|
| Dimensions (D × W × H) | 480 × 304 × 464.5 mm | 447.5 × 287.5 × 446.4 mm |
| Motherboards | E-ATX under 280 mm, ATX, Micro-ATX, Mini-ITX | Back-connect ATX, E-ATX under 280 mm, ATX, Micro-ATX, Mini-ITX |
| GPU clearance | 430 mm | 408 mm |
| CPU cooler height | 174 mm | 167 mm |
| ATX power supply | Under 232 mm | Under 220 mm |
| Radiator support | Side and bottom up to 360 mm; rear 240/120 mm | Top, side, or bottom up to 360 mm |
| Expansion slots | Six plus one | Six plus one |
| Warranty | One year | One year |
Footprint matters as much as clearance. The standard O11 Vision is 480 mm deep and 464.5 mm tall; the Compact is 447.5 mm deep and 446.4 mm tall. Measure the desk or shelf space before you commit, not after the box arrives.
Fan support is not fan supply. Both pages list mounting positions, and neither promises populated fans, so budget for the radiators and fans you plan to add. Neither page states a current US retail price either, which means the number you remember from a forum post is probably stale. Our tested white fish tank case roundup tracks what sellers are charging right now.
Does A Big Clearance Number Guarantee The Card Fits?
No. Published clearance assumes a bare interior, so a card measuring inside the limit can still fail on thickness, radiator stack, or the power connector.
What eats the margin:
- Radiator plus fan thickness. A 360 mm radiator on the side or bottom pulls the real card limit inward by 30 mm or more once a 25 mm fan is mounted.
- Card thickness across two, three, or four slots, and whether bottom fans or vertical-mount hardware occupy the same space.
- Bend radius behind a 12VHPWR or high-power connector. A stiff cable needs room before the side panel seats.
- Power-supply body length plus the space modular plugs and stored cables take up.
A slot count tells you the layout exists, not that your card clears it. Glass carries its own rule: lay panels down flat, support them while you work, and never tighten a panel against a twisted frame — tempered glass chips or shatters under uneven pressure.
Fit is half the build. Confirm the board’s BIOS supports the card, count the PCIe power connectors, check wattage headroom, and plan airflow from intake to exhaust. A case is an enclosure; it cannot rescue an underpowered system.
Run the checks in this order and the glass closes on the first try: board form factor and width, installed card length including the shroud, card thickness and cable bend, cooler height, supply length with cable room, radiator stack. Measure with a tape against the published numbers, round down, and treat a card within 15 mm of the limit as a maybe.
Common Questions
Does A Case That Lists ATX Also Fit Micro-ATX?
Usually yes, but verify the exact model. Case makers generally list every form factor a chassis supports, from E-ATX down to Mini-ITX, so an ATX case normally accepts Micro-ATX and Mini-ITX boards. The reverse is not true: a Mini-ITX case will not take an ATX board. Check the support list on the manufacturer’s page before ordering.
What Makes A PC Case A Fish Tank?
The label describes shape, not a standard. Fish tank cases wrap tempered glass across the front and one side, often with a pillar-free corner, so the interior reads like a display tank. A second chamber hides the power supply and cable bundle. Because the term is informal, none of it tells you whether your card fits — only the spec sheet does.
How Much Room Should I Leave Around My Graphics Card?
Leave room for everything sharing that space. Measure the installed card, shroud included, then add the thickness of any side or front radiator and its fans. Keep roughly 20–30 mm behind the card for the power connector’s bend. Round the card measurement down, and treat anything within 15 mm of the published limit as a gamble.
Sources
- Lian Li. “O11 VISION” Specification page for the O11VW White: dimensions, motherboard support, 430 mm GPU clearance, 174 mm cooler height, power-supply limit, radiator positions, and one-year warranty.
- Lian Li. “O11 Vision Compact” Specification page for the O11VPW White: 408 mm GPU clearance, 167 mm cooler height, back-connect ATX support, and 360 mm top, side, and bottom radiator positions.