How to Choose the Right Height for a Wood Walking Stick | Measure to Wrist Crease

Cut a wood walking stick so its handle sits level with the wrist crease while you stand in walking shoes with your arm relaxed — that puts a slight bend in your elbow and keeps your posture upright.

A stick cut a few inches too tall forces your shoulder up with every step; one cut too short drops your shoulder and tilts your torso. Neither is dangerous on its own, but both wear you down over a long walk. Whether you’re sizing a store-bought stick or trimming a piece of wood you’ve already shaped, the measurement below takes about two minutes and gets you within a half-inch of correct.

Wood doesn’t grow back. Unlike an adjustable aluminum cane, a trimmed hardwood shaft can’t be lengthened, so the real skill here is measuring carefully and cutting gradually.

How Do You Measure a Wood Walking Stick?

Measure from the floor to the wrist crease — the line where your palm meets your forearm — while wearing your normal walking shoes. That distance becomes the handle height; the elbow should still carry a light bend when you grip it.

Here is the procedure, in the order that avoids the usual mistakes:

  1. Wear your walking shoes. A thick sole or heel changes the number by half an inch or more. Measuring barefoot is the single most common fitting error.
  2. Stand on a level surface, upright but relaxed, arm hanging at your side. Don’t lock the elbow or reach for the floor.
  3. Find the wrist crease. Measure floor-to-crease with a tape, or stand the stick beside your foot and slide it up until the handle top hits that line. Measure to the crease, never to the fingertips or palm.
  4. Grip the handle and check the bend. Your elbow should hold a slight, comfortable angle — not a straight arm, not a sharp fold.
  5. Watch your shoulders while you walk. They should stay level and your torso upright. If you have to lean toward the stick, it’s too tall; if you stoop, it’s too short.

Take off the rest in small increments, checking the fit in your shoes after each pass. Once you reach the line, rub a little beeswax or wood finish on the fresh cut to seal the end grain.

Wood Walking Stick Height Rules: What Elbow Angle Tells You

The elbow bend is your built-in measuring tool: roughly 15 to 30 degrees of flex with the handle in hand means the height is right. Mayo Clinic’s cane guidance specifies about 15 to 20 degrees; the American Academy of Family Physicians gives 15 to 30. Either way, a straight or sharply bent arm means the stick is mismeasured.

What You See Elbow Position What It Means
Shoulder rises, arm nearly straight Close to 0 degrees Stick is too tall — cut it down
Shoulder dropped, torso tilting toward the stick Sharply folded Stick is too short — replace the shaft
Level shoulders, upright torso, easy downward push 15–30 degrees Height is correct
Shoulder lifts only when walking fast Barely bent Borderline tall — trim half an inch and retest
Neck and low back ache after a short walk Any angle Fitting is off — remeasure in shoes

The AAFP’s cane guidance covers the posture side in more detail, noting that when both arms need support, crutches or a walker may suit better than a single stick.

What Should You Check Before Cutting and After?

Fit is only half the job; the stick also has to be structurally sound. A secure handle and an intact, non-slip rubber tip matter more than an inch of length, and the tip is what actually keeps you upright.

Run these checks before you cut and again once the stick is finished:

  • Inspect the ferrule. Replace a rubber tip that is worn, cracked, loose, or hardened. Old rubber loses grip silently.
  • Account for tip thickness. Never measure with the tip off and then fit it afterward — that’s a hidden half-inch.
  • Press down hard once. After cutting, lean weight on the handle with the tip flat on the floor. Any flex, split, or looseness in the shaft, handle, or ferrule means stop.
  • Don’t hand it down. A stick fitted for you won’t fit someone else — height, shoes, posture, and which hand you use all differ.
  • Refit after changes. A new pair of shoes, a shift in posture, or a replaced tip can move the right height.

A wooden stick is for balance and light weight transfer. If you need substantial support on one side, or stairs are part of your route, ask a physical therapist to fit you — a wrist-crease measurement doesn’t replace that assessment, especially after a fall or with nerve or joint problems.

Shopping for the shaft itself? Our tested wood walking sticks worth buying covers the handle shapes and ferrule quality that hold up to real use.

Getting the Fit Right the First Time

Measure in your walking shoes, to the wrist crease, arm relaxed. Fit the tip, seal the cut end, and press down hard to confirm the shaft is sound. If balance, pain, or a recent fall makes you unsure, have a therapist do the fitting.

Common Questions

Can I adjust a wooden stick after cutting it too short?

No — a cut wooden shaft can’t be lengthened. You can add a taller rubber tip or a ferrule extender for a small gain, but more than half an inch of correction usually means starting over with a new shaft.

Should I measure with the rubber tip on or off?

Measure with the tip installed, or add its height to your floor-to-crease number. The tip adds real length, and leaving it out of the calculation is one of the most common fitting errors. Fit the tip first, then measure, then cut — never the other way around.

Which hand should hold the stick?

Hold it in the hand opposite your weaker or more painful side, so you can shift weight away from that leg. This matters enough that a stick fitted for the left hand may feel wrong in the right, so measure on the side you’ll actually use. Ask a physical therapist if you’re unsure which side should take the load.

Sources

Scroll to Top