Blade size and type must come from your exact trimmer model’s approved list, because diameter alone never proves a cutting attachment fits.
A trimmer that kicks back with the wrong blade is not a trimmer problem — it is a mounting-hole, guard, and handle mismatch that the label would have caught. The route to the right blade size and type for your weed eater runs through one document: the compatibility list for your exact model. Everything below follows that list, from the four attachment families to the mounting diameters that decide whether a blade bolts on at all.
Which Cutting Attachment Fits Which Job?
Each attachment family handles a distinct kind of growth, and stepping up a category is how people break equipment. Match the attachment to the vegetation, then confirm the machine is cleared for it.
- Nylon line heads — ordinary grass, lawn edges, light vegetation. Line sizes vary by head; the FS 361 runs.095 to.155 inch depending on the approved head, and its AutoCut 46-2 uses.105-inch standard line or.118-inch optional.
- Flexible plastic blades — a unit running a PolyCut head is classed as a trimmer, not a brushcutter.
- Metal grass blades — dense or heavy grass.
- Brush knives — tougher brush and overgrowth; the FS 251 and FSA 135 specify a 250-mm blade with a 25.4-mm mounting diameter.
- Circular saw blades — thinning brush and cutting small trees up to 4 cm (1½ inches) across, per the STIHL Trimmer and Brushcutter Safety Manual. Approved FS brushcutters only, and only with a bicycle handle and double shoulder harness — never a J handle or loop handle.
How Do You Confirm Blade Size And Type On Your Own Model?
Work the manufacturer’s list in order and stop at the first mismatch. STIHL’s cutting heads and blades selection chart is the reference document for this check.
- Read the exact model and version off the machine’s label or manual.
- Pull that model’s approved cutting-head and blade list. Shaft diameter and an advertised “universal fit” are not substitutes.
- Match the mounting-hole diameter.
- Match the line or blade size to the selected head — a bigger line is not automatically permitted.
- Confirm the handle, harness, guard or deflector, and barrier bar the attachment requires.
- Install per the model’s instruction manual. Only attachments authorized for that FS model go on.
- Inspect blades for cracks, bending, missing teeth, or wear, and sharpen grass blades once every cutting edge dulls.
Installation is done when the attachment seats flush with no gap at the mounting hole and the guard clears the blade through a full hand rotation.
What Do Approved Attachments Cost?
Prices sit in a narrow band, so the real constraint is compatibility rather than budget. STIHL USA’s cutting-tools page lists these current US prices:
| Attachment | Listed Price | Notes |
|---|---|---|
| AutoCut 36-2 | $39.99 | Approved on FS 251 and FSA 135 |
| DuroCut 20-2 | $39.99 | Approved on FS 251 and FSA 135 |
| TrimCut C 52-2 | $39.99 | Line head, current catalog |
| PolyCut 28-2 | $39.99 | Flexible plastic blades |
| AutoCut 46-2 | $52.99 | .105-inch standard line on FS 361 |
| DuroCut 40-4 | $59.99 | Approved on FS 361 |
| PolyCut blades 2-2, 3-2 (8-pack) | $8.99 | Replacement wear parts |
| PolyCut blades 6-3, 7-3, 30-3, 41-3 | $13.99 | Replacement wear parts |
Model-level pricing follows the same pattern. If you are still deciding what to mount a blade on, our roundup of weed eaters that accept blades narrows the machine choice.
Where Do Blade Setups Go Wrong?
Most failures trace to one unsafe shortcut — inferring fit from blade diameter instead of the full specification. Engine or motor, gearbox, guard, handle configuration, harness, attachment direction, and approved part number all have to agree with the manufacturer’s list.
The STIHL Trimmer and Brushcutter Safety Manual is direct about the stakes: improper use can cause serious or fatal injury. Wear eye protection and the deflector matched to the attachment. Skip rigid blades in stony areas, where impact hazards climb fast. This guidance covers STIHL trimmers, brushcutters, and clearing saws sold for the US market; it does not establish compatibility for other brands or models.
Common Questions
Can I put a metal blade on any straight-shaft trimmer?
No. A straight shaft alone does not authorize a metal blade. The machine must appear on the manufacturer’s approved attachment list, and the required guard, barrier bar, and handle configuration must be fitted. Running a metal blade on a trimmer that was never cleared for it voids the intended safety setup.
Does a bigger blade diameter mean more cutting power?
No. Blade diameter says nothing about whether the attachment fits, and a larger blade is not automatically permissible. Mounting-hole diameter, machine power, gearbox rating, and the approved part number all have to match. Work from your model’s list rather than from the blade’s advertised size.
When should grass blades be sharpened or replaced?
Sharpen grass blades once every cutting edge has gone dull, and inspect them each time for cracks, bending, missing teeth, or excessive wear. A blade showing any of those defects should come off rather than get sharpened. Replacement PolyCut blade sets run $8.99 to $13.99 at STIHL USA’s listed prices.
Sources
- STIHL USA. “Cutting Heads and Blades Selection Chart” Approved head, line, and blade pairings by model; version dated 2024-10.
- STIHL USA. “Trimmer and Brushcutter Safety Manual” Circular saw blade limits, handle and harness requirements, injury warnings.
- STIHL USA. “Cutting Tools” Current listed US prices for cutting heads and replacement blades.