3 Best Xtool D1/D1 Pro Air Assist and Fitting | Smoke-Free Cuts

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

If your xTool D1 or D1 Pro is leaving scorched edges and sticky tar lines on your wood, the missing piece is almost always steady airflow — not a new laser. An air assist pump pushes a stream of air right at the cutting point so smoke, dust and heat never settle on your material or your lens. This guide covers the three add-on kits worth bolting to your frame, explains what each one actually does, and tells you which fits the kind of work you do.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

You will see how the pumps differ in airflow, weight and noise, and which one suits a hobby bench versus a busy cutting schedule. The right pick here is simply the xtool d1/d1 pro air assist and fitting that matches your airflow needs and your tolerance for pump maintenance.

Top Picks

Comgrow Air Assist for Laser Cutter and Engraver
Best OverallComgrow Air Assist for Laser Cutter and Engraver4.5+★200+ ratingsThe dial-controlled pump that lets you dial the blast up or down for each material. Comgrow’s kit stands out because you can turn the airflow anywhere from fully off to 25 L/min.Check price on Amazon

How To Choose The Best Xtool D1/D1 Pro Air Assist and Fitting

An air assist is the cheapest upgrade that changes how your cuts look. It blows a jet of air exactly where the laser beam meets the material, which clears smoke and drops the surface heat. On a D1 or D1 Pro, that means darker outlines turn into pale, clean edges and your lens stops building up a brown film.

Match the airflow rating to your material, not the poster number

The airflow figure is measured in litres per minute, written L/min — it tells you how much air the pump moves each minute. A kit rated 30 L/min and one rated 35 L/min both clear smoke well on plywood and acrylic. Bigger numbers are not automatically better: too much air blows the flame out and can stop the cut burning through, which is why adjustable control is worth having.

Check the nozzle and hose fittings for your specific head

Your laser head takes a small nozzle, and the pump needs a hose that joins that nozzle to the air outlet. Some kits ship two nozzles and two tube connectors so you can adapt to different heads. Confirm the listing names your D1 or D1 Pro generation before you order, because a loose nozzle leaks air and kills the whole benefit.

Weigh noise and vibration against your workspace

A pump that rattles across the bench can shift your workpiece mid-cut, and a loud one is miserable in a spare room. Look for rubber feet and a stated noise figure in decibels (dB — the scale used to measure sound level). Quieter pumps let you run evening sessions without ear defenders or complaints.

Side-by-Side Comparison

Model Best For Airflow Weight Compatibility Amazon
Comgrow Air Assist Kit★ Best Overall Adjustable flow for mixed materials 0 to 25 L/min adjustable 3.54 pounds D1/D1 Pro and other heads Amazon
Ktondic Air Assist 35 L/Min Strong steady airflow on thick stock 35 L/min 4.11 pounds D1 and D1 Pro Amazon
PYXGLAQ Air Assist Pump Quiet bench work and clean edges 30 L/min 3.74 pounds D1 and D1 Pro Amazon

Detailed Reviews

★ Best Overall

1. Comgrow Air Assist for Laser Cutter and Engraver

Our pick — 4.5+★ from 200+ verified ratings; the strongest balance of quality and price.

Adjustable 0-25 L/minTwo nozzles included

The dial-controlled pump that lets you dial the blast up or down for each material.

Comgrow’s kit stands out because you can turn the airflow anywhere from fully off to 25 L/min. That range matters in real work: a gentle stream on thin veneer, more push on thick plywood, and a full blast when you need smoke gone fast. You are not locked into one fixed gust the way a single-speed pump forces on you.

You can dial the airflow knob like a tuning tool, not just flip it on or off, so you match the blast to each job. The box includes two air assist nozzles and two tube connectors, so you do not need to hunt for a separate fitting to reach your D1 or D1 Pro head. The maker states it also works with other brands of laser heads. Its small footprint lets it tuck beside the frame instead of eating bench space.

Weigh it against the Ktondic and the difference is weight and top-end push. The Comgrow tips the scales at 3.54 pounds versus the Ktondic’s 4.11 pounds, so it is the easier one to lift off a shelf. But it tops out at 25 L/min where the Ktondic runs to 35 L/min, so if you cut thick stock all day, the Ktondic’s stronger fixed stream has the edge. Where the Comgrow wins back ground is control — the adjustable dial is the single thing buyers talk about most, and it is easy to see why on mixed-material jobs.

What earns it first place

  • Adjustable 0 to 25 L/min flow you can tune per material
  • Two nozzles and two tube connectors in the box
  • Lighter at 3.54 pounds than the Ktondic’s 4.11 pounds
  • Small enough to sit beside the machine without crowding it

Where it asks for care

  • The lower 25 L/min ceiling than the Ktondic’s 35 L/min
  • Pump lifespan is the recurring gripe — treat it as a wear part

Reach for this if: you cut and engrave a mix of thin and thick stock and want to set the airflow to suit each one.

Look elsewhere if: you only ever run thick material at full power and want the strongest fixed stream available.

Top Airflow

2. Ktondic Air Assist for Laser Engraver, 35 L/Min Pump

35 L/min airflowRubber anti-vibration feet

The strongest stream here at 35 L/min, built for deep cuts and long sessions.

Airflow is the headline, and the Ktondic pushes the most of the three at 35 L/min. That extra push blows smoke and powder downward so it never drifts up into the laser port — which protects your lens and keeps the machine running longer between cleans. On thick stock the stronger stream also drives the beam deeper, so a job that stalled before now cuts through cleanly.

Four rubber feet soak up the shake and the whine, so the pump stays put and your workpiece does not creep — that is what separates it from the PYXGLAQ. The maker also states the airflow holds steady rather than fading over a long session, which matters on a multi-hour run. Buyers sum up the core job as “clears smoke well,” and the stream here does it with room to spare.

The honest catch is weight and a dash of uncertainty. At 4.11 pounds it is the heaviest of the three — noticeably chunkier than the Comgrow’s 3.54 pounds — so it is the one you notice when you move it around. And its buyer sentiment is genuinely mixed on whether it is worth buying, unlike the Comgrow’s smoother reception. If you want a fixed, strong stream and you do not need a dial, this is a solid fit; if you want adjustable control, the Comgrow is the better call.

Cutting muscle: 35 L/min is the top figure across these three pumps, and the four rubber feet keep it stable and quieter during long runs.

The trade-off to know: Heaviest at 4.11 pounds with a fixed, non-adjustable stream — strong for thick stock, but no dial to ease off on delicate work.

Best matched to: thick stock and long cutting sessions where a strong, steady blast matters most.

Not the one for: anyone who wants to turn the airflow down for thin veneer or fine engraving.

Quietest Pick

3. PYXGLAQ Air Assist for Laser Cutter and Engraver

Under 36.5 dB30 L/min airflow

Under 36.5 dB and built for a calm, accurate bench in a shared room.

Noise is where the PYXGLAQ makes its case. It runs under 36.5 dB, a level that lets you sit next to it without flinching, and it pairs that with vibration-reducing feet so the whole frame stays steady. Steady feet mean your cut lines land where you planned them instead of wandering, which is the quiet accuracy win most people do not think to look for.

Its 30 L/min stream sits between the Comgrow’s 25 L/min ceiling and the Ktondic’s 35 L/min, so it clears smoke and dust well without blowing the flame out. The maker states that steady flow cuts down on carbon buildup, which gives paler edge lines and smoother surfaces. Setup is stated as a few minutes, and it is built for the D1 and D1 Pro specifically, so the fittings line up rather than needing adapters.

Measured against the Comgrow, the two are close in size. The PYXGLAQ measures 6 x 3.5 x 2.6 inches while the Comgrow comes in at 5.91 x 3.94 x 1.97 inches — the PYXGLAQ is a hair taller and narrower, and neither crowds a bench. The thing to keep in mind is its quieter 30 L/min stream versus the Comgrow’s adjustable range: you get fixed flow here, so there is no dial to ease off on delicate engraving. If a hushed workshop and clean edges matter more than tuning, this is your pump.

Why quiet-priority buyers like it: Under 36.5 dB with vibration-reducing feet, so evening sessions stay peaceful and your cuts stay accurate.

Honest limit: Fixed 30 L/min flow with no adjustable dial, so thin-material work has no way to tone the blast down.

Pick this when: your laser lives in a spare room or shared space and you want clean edges without the drone.

Pass on this if: you need to fine-tune airflow on different materials rather than run at one steady push.

Know the Specs

Airflow in L/min

Airflow is how much air the pump pushes each minute, written in litres per minute (L/min). More flow clears smoke and dust faster and can help the beam cut deeper on thick stock. But the makers themselves warn that too much air can blow the flame out and hurt combustion, so an adjustable pump gives you the best of both — strong flow for thick stock, gentle flow for fine work.

Noise in dB

Noise level is measured in decibels (dB), the scale used for sound. A pump rated under 36.5 dB is quiet enough to run beside you without strain. Lower noise plus vibration-reducing feet also means your machine stays steady, which keeps cuts accurate rather than wandering.

Common Questions

Will an air assist pump fit both the D1 and the D1 Pro?
Check the listing before you order. The Comgrow kit ships two nozzles and two tube connectors and is stated to work with other brands of laser heads including the D1 and D1 Pro. The Ktondic and PYXGLAQ are both built for the D1 and D1 Pro specifically, so their fittings line up with those heads.
Is more airflow always better for cutting?
No. Comgrow’s own guidance notes that too much air volume can hinder combustion, which is why a steady, controlled stream beats a huge fixed blast. More flow clears smoke and protects the lens, but on thin material a strong gust can stop the cut burning through cleanly.
Do I need a dial to adjust the airflow?
Only if you work a mix of materials. The Comgrow has an adjustable range from 0 to 25 L/min, so you can ease off on thin veneer and push harder on plywood. The Ktondic runs at a fixed 35 L/min and the PYXGLAQ at a fixed 30 L/min, which is simpler but leaves no room to tune.
How loud is an air assist pump in a home workshop?
It depends on the model. The PYXGLAQ is rated under 36.5 dB, a quiet level that will not dominate a room. If the listing does not state a noise figure, expect the pump to make itself heard and plan for ear protection on long sessions.
How do I connect the pump hose to my laser head?
The pump’s air outlet connects to a nozzle on your laser head through a short tube. Kits that include spare nozzles and tube connectors, like the Comgrow, let you adapt without buying fittings separately. Make sure the nozzle is snug — a loose joint leaks air and weakens the whole stream.
Does an air assist really protect the laser lens?
Yes. By blowing smoke and particles down and away, the pump keeps them from rising into the laser port where they would coat the lens. That means fewer lens cleans and a longer working life for the optics. The Ktondic and PYXGLAQ both build their pitch around this lens-protection job.
How heavy are these pumps and do they take up much bench space?
They are small and light enough to sit beside the frame. The Comgrow is 3.54 pounds, the PYXGLAQ is 3.74 pounds and the Ktondic is 4.11 pounds — none of them needs a lot of room, and all are easy to move off the bench when the job is done.
How long will the pump last before I need a replacement?
It varies, and the honest answer is to treat it as a wear item. Comgrow’s buyer feedback flags durability as mixed, with pumps giving out after several months of use for some. Keep the pump clean and switch it off between sessions to give it the best chance of a long run.
Will an air assist make my edges cleaner and less scorched?
That is the main point of the upgrade. By dropping surface temperature and clearing smoke, the airflow cuts down on burnt edges and carbon buildup on your wood. The PYXGLAQ states it reduces scorching and gives more uniform edges, and the Comgrow pitches its heat dissipation for the same cleaner look.

The Bottom Line

For most D1 and D1 Pro owners, the Comgrow Air Assist Kit is the one to grab, because its adjustable 0 to 25 L/min flow lets you tune the blast to whatever you are cutting and the two nozzles mean it fits without hunting for parts. If a strong fixed stream on thick stock is your priority, the Ktondic 35 L/min pump pushes the most air of the three. And if your laser lives in a shared room, the PYXGLAQ runs under 36.5 dB (decibels, a measure of sound level) so you keep the peace while the edges come out clean.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top