Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
You already paid for the air conditioner — the gap beside it is what’s costing you. Those flimsy plastic accordion wings that came in the box leave a sliver of daylight and a steady trickle of hot air, and no amount of cranking the dial fixes it. A proper side panel kit is a 7/8-inch foam slab or a vinyl accordion curtain that fills that gap completely, so the cold air you paid for stays in the room and the street noise stays out.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Below you’ll find nine kits that actually seal the gap, sorted by how they handle the job. Each one is measured against the same three things — thickness, cut-to-fit range and how the adhesive holds. Here is how to read the numbers on any window ac side panels kit before you spend.
Top Picks



How To Choose The Right Window AC Side Panels
The gap beside a window air conditioner is a few inches of open air that leaks heat all season. These panels are the fix, but only if they actually fit your opening. Measure first, then pick your material.
Thickness And What It Blocks
A panel’s thickness decides how much heat it stops. Most kits here sit around 7/8 inch of foam, which is a solid middle ground for a typical window opening. If you are sealing a unit that runs all winter, a thicker or double-layer panel gives you more barrier against cold coming in.
Height, Width And Cut-To-Fit
The common panel size is 17 inches high by 9 inches wide. That covers most standard window units, but the width you actually need depends on how far the window slides open. A panel you can trim with a knife is more forgiving than a fixed-size one, because you can shave it down to a snug fit rather than forcing it.
Adhesive Or Channels
Foam on its own will sag. What keeps it in place is a self-stick plastic channel that grips the factory side rail and holds the foam upright. Kits that ship with channels tend to sit flatter against the unit than kits that rely on tape alone. Check that the channel is included before you buy.
Foam Or Vinyl
Foam panels are soft, quiet and easy to cut — they absorb vibration and muffle the compressor hum. Vinyl accordion panels are rigid and fold out like a curtain, so they replace a broken factory wing rather than covering it. Foam suits a unit with intact plastic wings; vinyl suits a unit whose wings have cracked off entirely.
Side-by-Side Comparison
| Model | Best For | Panel Size | Material | Pack | Amazon |
|---|---|---|---|---|---|
| moonoom 4 Pack Foam Block Kit★ Best Overall | Full sealing kit | Blocks + strips | Foam + tape | 2 blocks + 2 rolls | Amazon |
| Forestchill Insulation Foam PanelsWidest Coverage | Wide BTU coverage | 17″ H x 9″ W x 7/8″ thick | Foam | 2 panels + channels | Amazon |
| GCGOODS Insulated Foam PanelsSharpest Look | Top seal strip included | 17″ H x 9″ W + 39″ strip | Foam, PU leather surface | 2 panels + top strip | Amazon |
| YoleShy Side Panels | Budget gap filler | 17″ H x 9″ W x 7/8″ thick | Foam | 2 panels | Amazon |
| Trenton Gifts Insulation Panels | Year-round sealing | 18″ L x 9″ W | Foam | 2 panels | Amazon |
| Air Jade Side Panels | Light blocking | 17″ W x 9″ D x 0.87″ thick | Foam | 2 panels + channels | Amazon |
| BEWAVE Side Panel Kit | Clean look indoors | 17″ L x 9″ W x 7/8″ thick | Foam, leather-pattern | 2 panels + channels | Amazon |
| LBG Products Double Layer Kit | Maximum insulation | 17″ H x 10″ W | Double-layer foam | 1 pair + tape | Amazon |
| Mxclimate Accordion Kit | Replacing broken wings | Fits 8,000 BTU units | Vinyl accordion + frame | 2 panels + frame | Amazon |
Detailed Reviews
1. moonoom 4 Pack Air Conditioner Foam Block
Our pick — 4.5+★ from 90+ verified ratings; the strongest balance of quality and price.
Four separate pieces of sealing gear instead of two flat sheets of foam.
Most kits give you a pair of panels and send you on your way. This one gives you two foam blocks plus a roll of black foam strip and a roll of white sealing tape, so you are sealing the bottom of the unit and the narrow gaps at once rather than hunting for extra tape later. That completeness is why it takes the top slot.
The foam is described by the maker as resistant to deformation and detachment, and it is meant to hold its sealing shape under normal conditions. In plain terms, the block does not slowly crush flat and leave you with a draft again next season. You measure both sides, cut the blocks to length, push them into the gaps, then run the strip and tape along the base where air sneaks under the unit.
What wins people over is the completeness — buyers report the blocks, strip and tape seal the base and side gaps as described, and the foam feels denser than expected in hand. The honest catch is scope: it is built around U-shaped air conditioner units, so a standard slide-in window unit may need a panel kit instead. A fair trade-off for a kit that seals more than one gap at a time.
What Makes The Kit Different
- Blocks, strip and tape arrive together — no separate sealing run
- Foam is made to resist deforming and pulling loose over time
- Works as a noise and dust barrier as well as a thermal one
Where It Stops Short
- Designed around U-shaped units rather than every window AC
- Blocks need cutting to length before they seal properly
Reach for this if: you own a U-shaped unit and want every gap around it closed in one purchase.
Look elsewhere if: your unit takes flat slide-in side panels — this kit is shaped for a different install.
2. Forestchill Window Air Conditioner Insulation Foam Panels
One 17-by-9-inch panel size, stated to cover units from 5,000 up to 22,000 BTU.
That range is the reason this kit belongs near the top for most people. Fewer BTU brackets to think about means less chance you order the wrong size. The foam measures 7/8 inch thick, which is enough mass to mute compressor vibration and hold back the heat that normally pours through the plastic wing.
Each panel comes with a self-adhesive plastic channel that glues to the existing side rail and grips the foam upright. The maker describes the adhesive as strong and long-term, so the panel is not relying on friction alone. You trim both panels to your opening with a knife, peel and stick the channels, then slide the foam home.
Whoever put this on a 250-square-foot room says it does the job — the room holds its cool, and one user notes the panels put a stop to a cold draft that had been creeping in. The recurring gripe is size: the foam can arrive slightly generous for a narrow opening, so measure and cut rather than forcing it. It is the most broadly compatible kit here, and it asks only for a careful trim.
Why this fits most windows: the stated 5,000-to-22,000 BTU span covers nearly every home window unit, and the 7/8-inch foam is thick enough to dampen noise as well as heat.
Smaller openings: the panels may run larger than you need, so keep a sharp knife handy and trim to fit instead of wedging them in.
Suits: anyone who wants one purchase to cover an unknown BTU rating without a second trip.
The caveat: plan on cutting — the panels are cut-to-fit, not cut-to-window from the start.
3. GCGOODS Window Air Conditioner Insulated Foam Panels, White
A white foam panel with a leather-look surface, plus a strip for the narrow gap on top.
Two panels close the sides. The extra in the box is a 39-inch by 1.5-inch top foam strip, which is the piece almost every other kit leaves out. Run it along the narrow slit above the unit and you have sealed all three sides rather than two, which is where most of the remaining draft hides.
The panel itself is 17 inches high by 9 inches wide, meant for units from 5,000 to 22,000 BTU, and it ships with self-adhesive tape and an instruction sheet. The white polyurethane (PU) leather-look face is the detail that changes how the install looks from inside the room — a clean white panel in place of a grubby plastic wing.
Insulation is what buyers single out as the strongest point, and it is easy to see why: the panels plus the top strip are working on three edges instead of two. The finish earns praise too — it reads as something you chose to install rather than a patch slapped on. Adhesion is the honest weak point; the tape can lift over time, so press it firmly onto a clean, dry sill before the panel goes on.
The three-sided seal: the 39-inch top strip is the rare extra that closes the gap above the unit, which is often where a draft sneaks through after the sides are done.
Worth knowing: the tape may need re-pressing as the season turns, so give it a firm, clean surface the first time.
Best for: a visible window where the patch has to look intentional.
Heads up: budget a few minutes to press the tape down properly — the panels are only as tight as the first install.
4. LBG Products Air Conditioner Side Panel Kit, Double Layer
Two layers of foam where the rest of the field gives you one.
The extra layer is the whole argument for this kit. A double-layer side panel means more material between your cool room and the outside heat, and LBG states it shades 80% of the light that would otherwise come through the gap. The panels run 17 inches high and 10 inches wide, slightly wider than the 9-inch standard, and are built for units from 5,000 to 20,000 BTU.
Installation is flexible — the kit is made for both a clip-on type and a flat type of mounting, and it can be cut and adjusted to your window. A roll of insulating tape, an instruction sheet and the pair of panels come in the box, with a self-stick side channel doing the holding.
Where this one asks for care is the install itself. The double layer is stiffer than a single sheet, so some panels crack if they are forced rather than trimmed. Cut generously per the instructions, mount gently, and the rigidity works in your favor instead of against it. This is the pick for a hot, sunny window where the light and heat load matter.
Why It Holds Heat Back
- Double-layer foam is the thickest barrier in this group
- Stated 80% shading cuts the glare that comes through the gap
- Handles both clip-on and flat mounting styles
Where It Needs Patience
- The stiffer panel can crack if bent instead of cut
- Measure your window first — cutting is expected, not optional
Built for: a west-facing window that bakes, where blocking light matters as much as blocking heat.
Go gentle if: you want a panel that flexes easily — this one is rigid and prefers a careful trim to a hard push.
5. Air Jade Window Air Conditioner Side Panels, 2 Pack
The kit that seals the gap and pillows the light at the same time.
Two jobs happen when you close the side gap: the air stops moving and the sun stops leaking in. Air Jade’s panel does both, and the maker states that plainly — the foam blocks the light as well as the draft.
The panel measures 17 inches wide, 9 inches deep and 0.87 inch thick, a solid slab rather than a thin sheet. That thickness is what absorbs shock, softens the compressor hum and stops the day’s brightness from coming through the seam. You peel the two self-adhesive channels, set the foam, then cut any excess so the seal goes fully tight.
Insulation is what buyers talk about most with this kit — the panels hold cold air out of the gap, and one user points to a perfectly uniform cover on both sides. It is a straightforward kit with no top strip and no double layer, so if you want extra thermal muscle, the LBG above gives you more. If you just want the gap gone and the light gone with it, this does the pair neatly.
The light-blocking angle: the maker lists blocking light as a stated job alongside insulation — useful in a bedroom where the side gap glows all afternoon.
Where it lands: a single-layer panel with no top strip, so it seals the two sides well but leaves the top gap to you.
Pick this for: a bedroom window where a bright seam beside the unit wakes you up.
Not for: a room needing maximum thermal barrier — the top gap needs its own fix.
6. BEWAVE Window AC Side Panels, 2 Pcs Surround Kit
A white panel with a leather-pattern surface, cut to fit and installed in minutes.
White foam usually looks like white foam. This kit puts a leather-pattern finish on the face so it reads as a proper surround rather than a slab. The panels measure 17 inches long by 9 inches wide at 7/8 inch thick, and they come with a self-stick channel that the maker says leaves no residue if you ever pull it back off.
The panels can cover your existing side panel or stand in for a broken one, which gives you two ways to install depending on the state of your unit. Cutting is expected — the foam trims freely to your opening size — and the channels go on before the panels do.
The easy install is the part buyers keep coming back to; the panels go up quickly and the finished look earns its share of compliments. The honest catch is adhesion. The tape can lift off over time, especially on a sill that gets warmed by the sun, so clean the mounting surface and press the channels down hard before trusting them.
Why it looks better than plain foam: the leather-pattern white surface makes a visible gap look finished, which is the whole reason to pay a little more than a bare slab.
The one to watch: adhesion is the recurring grumble — a warm sill can let the tape lift, so treat the first press as the install.
Worth it when: the unit sits in a room guests see and the seal has to look tidy.
Think twice if: you want a set-and-forget stick — this one may need a re-press as the season warms.
7. YoleShy Window AC Side Panels, 17 x 9 x 1 inch, 2 Pack
Two black foam panels at a size that suits a standard opening.
Listed at 17 inches high by 9 inches wide by 7/8 inch thick, these panels land in the same size bracket as the premium kits but do less of the work around the edges. That gap is worth naming. Compare this against the Air Jade below it: the Air Jade product data lists a 0.87-inch thickness, and YoleShy lists 0.88 inch, close enough that thickness is not where this one loses.
What it lacks is a channel system in the stated contents. The kit includes two foam panels and nothing else in the box, so the panel is only as good as how you hold it against the rail. The maker describes the foam as soft, weather resistant and happy to reduce noise and vibration, and it is easily cut to the clearance you have.
Owners mention it functions as a gap filler and installs without trouble, and it earns its keep as a filler for the sides. The catch is that soft foam without a proper channel can feel flimsy in hand and may need extra securing. It costs very little and fills the gap — just go in expecting to supply your own channel or tape.
What you get for the money: two cut-to-fit foam panels at a standard size, with the material doing the sealing and no channel in the box.
The honest limit: soft foam on its own is flimsy, so plan on securing it yourself rather than relying on a self-stick rail.
Go here if: you have a standard opening and want a cheap foam filler you can trim yourself.
Reconsider if: you want the panels to hold themselves — this set expects you to supply the hold.
8. Trenton Gifts A/C Side Insulation Panels, Set of 2
A generous 18-by-9-inch panel that is designed to do the job on both sides of the unit.
The size here is a touch bigger than the 17-inch standard, which is helpful if your opening runs wide. Two foam panels come in the set, with self-stick side rails already attached so no tape of your own is needed. Up it goes onto the existing side panels, one on each side, and you are done.
The maker positions the panels for year-round use, keeping hot air out in summer and cold air out in winter, and adds noise reduction to the list. Insulation is what buyers rate most — the foam does its job of holding the temperature line. What to expect is that the material is a budget grade, and its staying power is not the selling point.
The panels perform as a seasonal filler — budget-grade foam for a summer install, not a permanent winter seal. For a summer-only install, this is a cheap and simple run; for a permanent winter seal, the foam is not the most sturdy of the group. Treat it as a fill for the gap you want closed now, not a fixture you stop thinking about.
The insulation holds up: the foam blocks the air path, and buyers credit it for doing that job at a simple setup.
The honest trade: it is basic material meant for a season’s use, so a full winter seal calls for something sturdier.
Best for: a seasonal summer install on a wide opening where the fitting matters more than the lifespan.
Less ideal for: a year-round seal — the foam is not built to stay put through every season.
9. Mxclimate Window AC Side Panels with Frame, Accordion Kit
A folding vinyl curtain that replaces the broken wing instead of covering it.
Every other kit on this list is foam. This one is a vinyl accordion — a set of folding panels with a frame, made to stand in for an old plastic side panel that has cracked or gone missing. If your factory wings are beyond saving, this is the format you need, because a foam slab only covers a wing that is still there.
The accordion expands to suit the opening and is stated to fit most window units of 8,000 BTU. The maker recommends measuring the window before you commit, and there is one hard compatibility note: the kit is not built for LG air conditioning units. Check the brand of your unit first — that single line saves a return.
The vinyl is meant to seal against dust, drafts and moisture, and it folds out to close the gap like the original wing did. The fit is where to focus your attention: it is sized for 8,000 BTU units, so a different rating needs a check against your opening before ordering. For a unit with a ruined plastic wing, though, this restores the look and the seal at once.
The Accordion Advantage
- Replaces a cracked or missing plastic wing outright
- Expands to close the gap, then folds flat when not installed
- Vinyl seals against dust, drafts and moisture
Check Before You Order
- Not compatible with LG air conditioning units
- Sized for 8,000 BTU units — confirm your rating first
The right call if: your unit’s plastic side wings have cracked and you want a rigid replacement rather than foam over a broken part.
Confirm first: your unit’s brand is not LG and its rating matches the 8,000 BTU fit, or the kit will not line up.
Know the Specs
Foam Thickness
The thickness of the panel — usually stated in fractions of an inch — decides how much heat and noise it stops. A panel around 7/8 inch is a common middle ground, thick enough to mute the compressor while still trimming easily with a knife. Thicker or double-layer foam gives you more barrier for a window that bakes in the sun.
Panel Dimensions
Height and width tell you whether a panel matches your opening. The typical panel is 17 inches high by 9 inches wide, with some kits running 10 inches wide or 18 inches long. Measure the gap beside your unit before you buy — a panel that is too small leaves a draft, and one that is too large needs trimming.
BTU Range
BTU (British thermal units) is the measure of how much cooling a unit puts out. Some kits state a range they fit, such as 5,000 to 22,000 BTU, while others are sized for a single rating. Matching the panel to your unit’s BTU gives you the best chance of a panel that sits flush without heavy trimming.
Self-Adhesive Channels
Foam alone will sag from the window sill. A self-stick channel is a plastic rail that glues to the existing side rail and holds the foam upright. Kits that include channels tend to sit flatter than kits that rely on tape alone, so check the stated contents before you buy.
Common Questions
Will these side panels fit my window air conditioner?
Should I buy foam panels or a vinyl accordion kit?
How thick should a side panel be?
Can I cut a foam panel to fit a smaller opening?
Do these panels help in winter as well as summer?
Will side panels reduce the noise from my air conditioner?
Do I need a channel or does tape alone work?
Will a side panel kit work with an LG window unit?
How do I keep the panels from peeling off the window sill?
Is a side panel kit cheaper than running the AC harder?
The Bottom Line
For most people, the foam block kit is the winner because it seals more than one gap in one purchase. The moonoom set gives you blocks, strip and tape together, and it earns the top slot. If you want one purchase to cover an unknown BTU rating, reach for the Forestchill panels with their stated 5,000 to 22,000 BTU span. And when the plastic wings have already cracked off, the Mxclimate accordion kit is the format that restores the side panel. Measure the height and width of your gap first, and the right kit among these nine is easy to spot.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.





