9 Best Western Plow Parts | Steel That Beats Road Salt

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

When a plow part fails in a snowstorm, you are not shopping for a bargain — you are hunting for whatever gets the blade moving again before the driveway fills back in. The parts below are all confirmed fitments for Western plows, from blade markers and trip springs to hydraulic oil and a replacement plow motor. Pick the one that matches the part that let you down, and check the OEM number against your own unit before you order.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

Replacing a worn plow component starts with matching your original part number, then choosing a piece built to survive salt, grit and freeze-thaw cycles. This breakdown covers the Western Plow Parts most likely to be the one you actually need.

Top Picks

Snow Plow Blade Markers/Guides Kit 27' 304L Stainless Steel Base Hardwares
Best OverallSnow Plow Blade Markers/Guides Kit 27″ 304L Stainless Steel4.5+★500+ ratingsTall enough to spot over a plowed bank, tough enough to fold and spring back. The blade edge is where you steer from, and losing sight of it in deep snow is how you chew up a curb or a lawn.Check price on Amazon
Buyers (Pack of 2) 1' Hitch Pins with Hairpin Cotters for Western Snowplows 93028 Unimount Plow
Best Small FixBuyers Pack of 2 1″ Hitch Pins with Hairpin Cotters 930284.5+★90+ ratingsThe little pin that decides whether your blade stays on the truck. Hitch pins are the cheapest part on a plow and the one that ruins your morning fastest when it shears.Check price on Amazon
Buyers Products 1302205 SAM Trip Spring, Replacement Part for Western Snowplow
Best for Trip ResetBuyers Products 1302205 SAM Trip Spring4.0+★100+ ratingsWhen the blade stops tripping, this coil is what springs it back. A trip spring is the safety valve of your plow.Check price on Amazon

How To Choose The Best Western Plow Parts

Buying a plow part is a fitment job first and a quality job second. If the part does not bolt to your blade, the best steel in the world is scrap. So work in this order: confirm the OEM number, then the physical size, then the material. That sequence saves you a return trip in the middle of a storm.

Match the OEM number before anything else

Every Western plow part carries an original part number, and aftermarket makers list the numbers they replace. A blade marker kit that names 62265 alongside Blizzard, Boss, Sno-Way and Western fitments is speaking directly to your machine. A trip spring that replaces Western 23040 is a different conversation entirely. Write your old number down before you start shopping — a photo of the worn part next to a tape measure helps too.

Size is the second gate, and it is unforgiving

Shoe assemblies live or die on shaft length and diameter. One pair here runs a 6 3/4-inch rod at 1 inch across, another runs a 7-inch shaft at 1 1/64 inches. A hair of difference means the shoe will not seat. Measure your old shoe with a caliper if you have one, or match the OEM number your manual lists. For hitch pins, the diameter and the cotter size both need to line up with your A-frame.

Material decides how many seasons you get

Road salt eats mild steel alive. Stainless and cast iron are the two materials that keep coming back in plow hardware for good reason. A 304L stainless base on blade markers resists rust even when packed with wet snow. Cast iron shoes take the grinding contact with pavement. Rubber and steel-wire marker shafts flex instead of snapping when a snowbank folds them over. Match the material to the wear the part actually sees — stainless for salt spray, cast iron for pavement grinding.

Electrical and hydraulic parts need exact ratings

A plow motor is a 12-volt unit spinning clockwise — get the rotation wrong and it fights the pump. Solenoids need the post count and shape to match the factory bracket. Hydraulic oil needs a cold rating low enough for your climate, and a viscosity that the pump was designed around. These are not places to guess.

Side-by-Side Comparison

Model Best For Part Type Material Key Size Amazon
Snow Plow Blade Markers/Guides Kit 27″★ Best Overall Seeing your blade edge in deep snow Blade markers 304L stainless base, rubber and steel wire 27.95 in long Amazon
Buyers 2-Pack 1″ Hitch Pins with Hairpin CottersBest Small Fix Locking the plow to the truck A-frame Hitch pins Metal, bronze finish 1 in pin diameter Amazon
Buyers 1302205 SAM Trip SpringBest for Trip Reset Restoring the blade trip action Trip spring Steel coil spring 14.75 in long Amazon
Western HD Round 4 Post Solenoid 56131-2 Fixing a dead hydraulic pump circuit Solenoid Heavy duty metal housing 4-post round Amazon
49317 49308 9 Pin Wiring Harness Repair Kit Replacing cracked plow lighting wiring Wiring harness Copper, nylon, PVC 9-pin connector Amazon
6 Quart -50° Snow Plow Hydraulic Oil Cold-climate hydraulic protection Hydraulic oil Oil with anti-wear and anti-freeze additives 6 quarts Amazon
Snow Plow Shoe Skid Foot Assembly for Western 49067 Precise fit matching on Western and Boss blades Skid shoes Cast iron 7 in shaft, 6 in disc Amazon
DB Electrical Snow Plow Motor Replacing a burned-out plow pump motor Plow motor New aftermarket build 12 volt, CW rotation Amazon

Detailed Reviews

★ Best Overall

1. Snow Plow Blade Markers/Guides Kit 27″ 304L Stainless Steel

Our pick — 4.5+★ from 500+ verified ratings; the strongest balance of quality and price.

304L Stainless Base27.95 Inches Tall

Tall enough to spot over a plowed bank, tough enough to fold and spring back.

The blade edge is where you steer from, and losing sight of it in deep snow is how you chew up a curb or a lawn. These markers stand 27.95 inches tall, so the tip clears a plowed bank that would swallow a shorter guide. That height puts the edge back in your line of sight from the driver’s seat.

What wins people over is the 304L stainless base plate. The 304L stainless plate and matching install hardware shrug off wet snow without rusting, which is the failure that kills cheaper marker kits. The shaft itself is low-temperature-resistant rubber wrapped around high-strength steel wire — not hollow plastic. Bend one against a snowbank and you can straighten it by hand.

Fitment covers most Blizzard, Boss, Sno-Way and Western plows, plus a wide spread of other machines, so the same kit reaches a Polaris side-by-side and a full-size truck blade. A reflective strip ships as a gift so you can add a brighter marker for night work. One honest note: the strip is stick-on, so where it lands and how well it holds are up to you.

What holds up season after season

  • 304L stainless base resists rust even packed with wet snow
  • Rubber-and-steel-wire shaft bends and returns instead of snapping
  • 27.95-inch height keeps the blade edge visible over plowed banks
  • Complete stainless install hardware included in the kit

Where it asks a little of you

  • Reflective strip is a stick-on extra, not molded in
  • Bolt pattern is broad but not universal — check your base first

Take these if: you run a Western blade and want to see the edge in real time.

Think twice if: your plow mount uses a base pattern this kit does not list.

Best Small Fix

2. Buyers Pack of 2 1″ Hitch Pins with Hairpin Cotters 93028

1″ Pin Diameter2-Pack with Cotters

The little pin that decides whether your blade stays on the truck.

Hitch pins are the cheapest part on a plow and the one that ruins your morning fastest when it shears. This two-pack from Buyers Products carries a 1-inch pin diameter, sized for the Western Heavyweight A-Frame 62170 and the Unimount 93028 setup. The bronze-finished metal body is built as a fastener first, not a decorative piece.

Each pin pairs with a hairpin cotter at 5/32 inches by 3 inches. That is the safety clip that keeps the pin from walking out while the blade bounces over frozen ruts. You get two of each in the pack, so you can fit the frame and keep a spare in the toolbox. At 2.6 pounds for the set, these are solid steel pins, not stamped lookalikes.

The only real caution is fitment. Buyers asks you to confirm your OEM number, model, spec code and serial number before ordering, because one part number can replace several originals. Measure your old pin across the shaft and check the cotter size if you are unsure. Unlike the blade markers above, this is a single-purpose part — if the number is wrong, it is wrong.

Why it punches above its size: a 1-inch diameter steel pin with a properly sized cotter is the difference between a blade that stays locked to the A-frame and one that drops on the first hard bump.

The fitment chore: you have to do the number-matching homework yourself, so keep your old pin in hand while you order.

Worth grabbing: if you run a Unimount or Heavyweight A-frame and want a spare set on the shelf.

Hold off: until you have matched your OEM number and measured the pin shaft.

Best for Trip Reset

3. Buyers Products 1302205 SAM Trip Spring

Replaces Western 2304014.75″ Length

When the blade stops tripping, this coil is what springs it back.

A trip spring is the safety valve of your plow. Hit something buried and the blade folds forward so the impact goes into the spring instead of your frame. This Buyers 1302205 replaces OEM number Western 23040, which is the number that matters when you are cross-checking your own machine.

The coil runs 14.75 inches long with a 2.25-inch outside diameter. That length sets how much travel the blade has before it resets, and the diameter determines whether it seats cleanly in the factory bracket. The whole spring weighs 6.13 pounds, so you are getting real coiled steel rather than a flimsy replacement.

Buyers sells this as a direct OEM replacement, which means installation is a bolt-on job rather than a modification. Compared with the small hitch pins above, this is a heavier, more mechanically loaded part, and it should be inspected whenever you notice the blade failing to return square. If your blade is dragging at an angle after a trip, this spring is the first thing to check.

Why it earns the swap

  • Direct replacement for Western OEM 23040
  • 14.75-inch coil length matches factory travel
  • 2.25-inch outside diameter seats in the standard bracket

Before you commit

  • Only fits machines originally running the 23040 spring
  • Heavier coil means a firm pull to seat it during install

Right call for: a Western blade that has stopped tripping square after a hard hit.

Wrong call for: anyone who has not confirmed their blade runs the 23040 spring.

Best Electrical Fix

4. Western HD Round 4 Post Solenoid 56131-2

4-Post RoundHeavy Duty Build

The four-post switch that wakes up your pump when the blade goes dead.

If your plow motor clicks but will not turn, the solenoid is usually the culprit. This heavy-duty round unit carries four posts and replaces OEM 56131-2 for Western plows. It is built to meet or exceed OEM quality, which matters on a switch carrying full pump current.

What wins people over is that it just works when you turn the key. Fit it, and the pump circuit closes the way it should. At 12 ounces it is a compact metal can, and the round four-post layout drops into the standard Western bracket. The pricing sits in the mid-range tier, well below the pump motor itself.

The install itself is a tight-quarters job. You are working around battery cables and a live circuit, so disconnect the battery first and photograph the wire order before you pull the old solenoid. The packaging box measures 5.1 by 3.7 by 3.2 inches, so it ships small enough to keep a spare on the shelf. If electrical work is not your thing, this is one part where a mechanic’s ten minutes can save you a headache.

The core reason to buy: a four-post round solenoid that matches the 56131-2 footprint and restores the pump circuit without a wiring workaround.

Be honest with yourself: this is a live-circuit swap, so if you are not comfortable with battery cables, hand it to someone who is.

Buy it when: the plow motor clicks and nothing moves — this is the first part to swap.

Leave it be if: your motor turns but the blade still will not lift; that is likely hydraulic, not electrical.

Best Wiring Repair

5. 49317 49308 9 Pin Wiring Harness Repair Kit

9-Pin ConnectorsPlug-and-Play

Two harnesses, one box, no splicing under the truck in the cold.

Chafed plow wiring is a slow killer — lights flicker, then stop, and you are tracing nine pins with a test light in a snowbank. This Lucklick kit bundles both the 49317 plow-side and 49308 truck-side harnesses with the 9-pin connectors that match the factory Western and Fisher configuration. It is a direct-fit connector, so you plug into the factory wiring instead of cutting and crimping.

The conductors are copper, sheathed in tough nylon insulation for abrasion resistance against the frame. A flat ribbon cable type keeps the run tidy, and the wire diameter is 1.4 millimeters. A PVC jacket and a protective dust cover over the terminals guard against moisture, salt debris and corrosion when the plug is not in use. That cover is a small detail that matters over multiple winters.

Where this fits, it fits cleanly — the connector matches the original layout for compatible Western and Fisher systems, including the 22335K and 1315310 plow-side and 22336K and 1315315 truck-side references. Where it does not fit is a different pin count or a non-standard harness. Count your pins before you order, because this is a 9-pin kit and nothing else.

What makes it a clean swap

  • Both plow-side and truck-side harnesses in one kit
  • Copper conductors with nylon abrasion protection
  • Dust cover shields terminals from salt and moisture
  • Direct-fit connector avoids cutting factory wires

What to watch

  • 9-pin only — will not fit a different connector layout
  • Fits listed Western and Fisher systems, not every brand

Pick this up: if your factory 9-pin harness is cracked or corroded and you want both sides replaced together.

Skip it: on a plow running a different pin count or a non-listed harness reference.

Best Cold-Weather Fluid

6. 6 Quart -50° Snow PLOW Hydraulic Oil

-50°F Cold Rating6-Quart Bottle

Hydraulic fluid that still flows when the temperature drops past freezing.

Thick fluid on a cold morning is why the blade lifts slow or not at all. This Mag 1 hydraulic oil is rated to -50°F with anti-freeze additives, so it stays workable in the kind of cold that makes lesser fluid drag. It replaces Meyer 15134, Western 49311, Fisher 28531, Buyers 1307005, Boss HYD01704-1 and Sno-Way 96005029 — a wide compatibility net for one bottle.

The anti-wear additives bond into a protective layer on the metal components inside a high-pressure pump. Viscosity measures 20.53 at 40°C and 4.36 at 100°C, which tells you the fluid thins predictably as it heats. That viscosity curve is what protects the pump and cylinders across a long plowing session.

Here is where it stands out against the wiring harness and solenoid above: this is maintenance, not repair, and it is the piece most people skip. You get six quarts in a single 192-fluid-ounce container, enough for a full system service or several top-offs through the season. What you do not get is a pour spout, so keep a funnel handy.

What earns its place: a -50°F rating and anti-wear chemistry in a quantity big enough to actually service the reservoir.

The practical catch: it pours from a plain bottle, so plan on a funnel and a rag or you will wear some of it.

Add it to the order: if your blade lifts sluggishly in deep cold and you have not changed the fluid this season.

Not the fix for: a pump that will not turn at all — check the solenoid and motor first.

Best Fit Precision

7. Snow Plow Shoe Skid Foot Assembly 49067 MSC01570

7″ Shaft LengthIncludes Pins and 38 Washers

A 1/64-inch difference is the whole reason this shoe earns its place.

Where the cast shoes above run a 1-inch rod, this ROP Shop pair runs a 7-inch shaft at 1 1/64 inches in diameter. That hair-thin difference is exactly why you measure rather than assume. A 6-inch disc and 8-inch total length complete the geometry, and the set ships with two shoes, two pins and 38 washers — enough to shim the height precisely.

The casting is long-wearing, heavy-duty cast iron, the same material logic that keeps the Western-branded shoes in service for seasons. It fits Western 49067 and Boss MSC01570 references, plus several other Western and compatible models. The generous washer count is the real advantage here — you rarely end up short on spacers during an install.

One caution before you order: this is a fit-first part. The listing asks you to match your original shoe’s shaft diameter and length, or verify against your OEM number, because the 1 1/64-inch shaft will not substitute for a 1-inch one. Measure with calipers, not a tape, and this becomes a straightforward swap.

The fitment truth: 7-inch shaft and 1 1/64-inch diameter make this the right shoe for the specific machines running that size.

Why the washers matter: 38 spacers across two shoes means you can dial in your blade height without a run to the hardware store.

The catch: if your old shoe is 1 inch across, this one is too big — measure first.

Order these when: your blade runs a 1 1/64-inch shaft shoe and you want a precise fit with plenty of shims.

Cross these off: if your calipers read 1 inch or your OEM number is not on the list.

Best Motor Replacement

8. DB Electrical Snow Plow Motor

12-Volt CW Rotation1-Year Warranty

A fresh 12-volt motor for the day the pump finally refuses to spin.

When the motor goes, the whole plow stops. This DB Electrical unit is a 100% new aftermarket build, not a rebuilt one, made to meet OEM specifications for Western Products. It runs 12 volts and rotates clockwise, which is the direction the pump expects — get that backwards and nothing works right.

The part number is 430-22047, and it replaces a long list of originals: Arrowhead 430-22047, Bosch F-000-MM0-804, Fisher 48543 and 48543-1 and 48543-1AM, J & N 430-22047, Lester 10770, WAI 10770N, Western Motors W-6804, and Western Plow 27753. It is listed as compatible with Western Products Suburbanite models. One motor covering that many cross-references means fewer dead ends when you are matching a number.

A one-year warranty backs it, with replacement offered within a year if it fails. That said, this is the most involved install in the group — you are pulling the old motor out of the pump housing and refitting a new one. Compared with the solenoid above, it is a bigger job and a bigger part, and it is the one you want to get right the first time. If you are unsure, confirm your OEM number with the seller before ordering.

Why it is a serious replacement

  • 100% new build, not remanufactured
  • 12-volt, clockwise rotation matches the pump
  • Cross-references a long list of OEM numbers
  • 1-year warranty with replacement coverage

Where to slow down

  • Fit is limited to Western Suburbanite-compatible models
  • Motor swap is a real wrenching job, not a plug-in

Best for: the owner whose pump motor is dead and who has confirmed the 430-22047 cross-reference.

Not for: anyone unsure of their OEM number — verify before you pull the old motor.

Know the Specs

OEM part numbers — your first filter

Every Western component traces to an original part number, and aftermarket makers list the numbers they replace. Western 23040 for a trip spring, 49067 for a skid shoe, 56131-2 for a solenoid. If your number is on the list, the part is meant for your machine. If it is not, no amount of quality helps. Write your number down before shopping, and photograph the old part next to a tape measure for reference.

Shaft and rod dimensions — the second gate

Skid shoe assemblies live or die on shaft diameter and length. One pair runs a 6 3/4-inch rod at 1 inch, another a 7-inch shaft at 1 1/64 inches. That 1/64-inch difference decides whether the shoe seats in the bracket. Measure with calipers, not a tape, and match the number your manual lists. The same logic applies to hitch pins, where the 1-inch diameter must line up with your A-frame.

Material — stainless versus cast iron

Road salt is the enemy, and the material fights back. A 304L stainless base resists rust even when packed with wet snow, which is why it shows up on blade markers and install hardware. Cast iron takes the grinding contact with pavement on skid shoes. Rubber and steel wire flex instead of snapping on marker shafts. Pick the material that matches the abuse the part will take.

Voltage and rotation — electrical exactness

A plow motor is a 12-volt unit spinning clockwise. The solenoid must match the round four-post layout, and a wiring harness must match the 9-pin count and factory connector. Hydraulic oil needs a cold rating low enough for your climate — the Mag 1 is rated to -50°F — and a viscosity the pump was designed around, here 20.53 at 40°C and 4.36 at 100°C.

Common Questions

How do I know which Western plow part I actually need?
Start with the OEM number stamped or cast on the old part. Match that number against the replacement listings, then confirm the physical size — shaft diameter, pin diameter, spring length or connector pin count. For a dead pump, the solenoid and motor cross-reference list tells you which part number you are chasing. If you are unsure, photograph the old part with a tape measure next to it and contact the seller before ordering.
Will a 1-inch skid shoe fit where a 1 1/64-inch shoe was?
No. The shaft diameter has to match the bracket bore. One shoe pair runs a 1-inch rod, another runs 1 1/64 inches. A hair of difference means the shoe will not seat properly, so measure with calipers and compare against your OEM number before you buy. The same caution applies to the rod length, which determines how much height adjustment you get.
How do I tell whether my problem is the solenoid or the plow motor?
A solenoid that clicks but does not pass current is a common failure. If the motor clicks and nothing turns, the solenoid is the first part to swap. If the motor itself will not spin even with good power, the motor is the culprit. The solenoid and motor here both list their cross-reference numbers, so you can verify which one your machine uses before ordering.
Does hydraulic oil cold rating really matter for a plow?
Yes. Cold fluid thickens, and a pump fighting thick fluid lifts slow or stalls. The Mag 1 oil here is rated to -50°F with anti-freeze additives, so it stays workable in deep cold. Its viscosity measures 20.53 at 40°C and 4.36 at 100°C. If you plow in serious cold and have not changed the fluid, its condition may be behind sluggish blade movement.
Can I replace just one skid shoe or do I need the pair?
You can replace one, but a mismatched pair wears at different rates and will throw off your blade height on one side. The shoe sets here ship as pairs — one pair runs 22 washers across two shoes, another includes 38 washers with the pins. A matched pair keeps the blade level, which is worth the small extra cost.
Will a 9-pin wiring harness fit my Western plow?
Only if your plow and truck side use a factory 9-pin connector layout. The Lucklick kit matches the Western and Fisher 9-pin configuration and includes both the plow-side and truck-side harnesses. If your machine runs a different pin count, or your harness reference is not on the fitment list, the connectors will not line up. Count the pins on your existing plug first.
Are stainless blade markers better than plastic ones?
A 304L stainless base resists rust even when packed with wet snow, which is the failure that takes out cheaper marker kits. The shaft on the C CLINK kit is low-temperature rubber over high-strength steel wire, so it bends and returns instead of snapping like hollow plastic. The 27.95-inch height also keeps the blade edge visible over plowed banks.
How long should a plow motor last?
No fixed lifespan applies to every setup, but a plow motor is a wear part that lives through heat, cold and heavy electrical load. When it fails, a 100% new aftermarket motor meeting OEM specs is the replacement path. The DB Electrical unit covers a wide range of OEM cross-references and carries a one-year warranty with replacement coverage.
Is there a difference between a Western and a Boss skid shoe?
Yes, and it is often just the shaft diameter or length. One pair here fits Western 49067 and Boss MSC01570 with a 7-inch shaft at 1 1/64 inches. Another pair replaces 49067, 49071, 60045 and 1303200C with a 6 3/4-inch rod at 1 inch. Some users of Boss V-plows report a fit mismatch on the second set, so verify your OEM number either way.

The Bottom Line

For most readers, the western plow parts winner is the Snow Plow Blade Markers/Guides Kit because it solves the everyday problem of seeing your blade edge in deep snow — the 304L stainless base resists rust while the rubber-and-steel-wire shaft bends and returns instead of snapping. If your blade has stopped tripping square after a hard hit, reach for the Buyers 1302205 Trip Spring. And if the pump motor finally gives out, the DB Electrical Snow Plow Motor is the clean replacement with a one-year warranty. Match your OEM number first, then pick the part that matches the failure — that is the whole game with plow parts.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top