Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your Samsung top-load washer walks across the laundry room floor or throws a DC error code mid-spin, the fix is usually four rods under the tub, not a new machine. This guide covers the WA45H7000AW A2 Parts that actually bring that drum back under control — suspension rods, a drain pump, and a water inlet valve — and tells you which one matches your symptom.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Match the part to the symptom and you can skip the service call entirely. Here is how to sort through WA45H7000AW A2 Parts and pick the one your washer is actually asking for.
Top Picks


How To Choose The Best WA45H7000AW A2 Parts
The hard truth about washing machine parts: they all look alike, and the wrong one installs fine and then misbehaves. The way to avoid that is to diagnose first and buy second. Every part below is confirmed compatible with the WA45H7000AW/A2 revision, but each one solves a different problem, so the right choice depends on what your machine is doing.
Read the symptom before you read the listing
A tub that bangs, wobbles, or throws a DC code (Samsung’s out-of-balance warning) during the spin cycle is telling you the suspension rods are tired. That is not a guess — the rod assembly is the sole support holding the inner drum level, and when a spring sags the tub tilts and the machine shakes. If the washer instead fills and then sits full of water, or you hear the pump but no water leaves, the drain pump is the part to look at. And a machine that dribbles water at the back or fills only with cold is pointing at the water inlet valve.
Length and count are the two numbers that matter
Suspension rods come in slightly different lengths, and a rod that is a fraction off will fit the socket but load the tub unevenly. Rods in this group run from 25.8 inches to 26.18 inches, which is close enough to look identical in a photo and different enough to cause trouble. Measure your original rod end to end before ordering, and confirm you are getting four rods in the kit — all the suspension sets here are 4-packs, and one new rod with three worn ones defeats the point.
Check the part number, not just the model name
Each listing here replaces a stack of factory numbers like DC97-16350U, DC97-16350E, DC97-16350T, and DC97-05280W. Those numbers cross-reference back and forth across Samsung’s lineup, which is useful — it widens your options — but also means the model list on the box can be long and messy. When in doubt, match your old part’s number or length to the listing rather than trusting the headline.
Plan for DIY time, not just parts
None of these repairs is delicate work. Suspension rods typically run about 20 to 30 minutes with a screwdriver and tape, and the drain pump and valve jobs need pliers and a Phillips head. Doing the install yourself with the vendor’s instructions is the real cost saver: you skip the service call entirely. Just cut power and water at the wall before you touch anything.
Side-by-Side Comparison
| Model | Best For | Part Type | Fixes | Quantity / Length | Amazon |
|---|---|---|---|---|---|
| WA50R5200AW/US Suspension Rods Kit★ Best Overall | All-around tub stabilization | Suspension rods | Wobble, balancing, DC code, banging | 4 rods, 26.18 in | Amazon |
| Upgraded DC97-16350U Suspension RodsWidest Fit | Widest cross-model coverage | Suspension rods | Vibration, drum imbalance, spin-cycle noise | 4 rods | Amazon |
| WA45T3200AW/A4 Suspension Rods by Vypart | Thicker forged rod body | Suspension rods | Shaking, DC/UR/UB/UL codes, noise | 4 rods, 1.9 lb | Amazon |
| WA45H7000AW/A2 Suspension Rods (zinc alloy) | Shorter 25.8-inch rod socket | Suspension rods | Shaking, vibration, DC/UR/UB/UL codes | 4 rods, 25.8 in | Amazon |
| DC97-19289F Washer Drain Pump Assembly | Washer won’t drain | Drain pump | F02/E5 codes, no drain, leaks, pump won’t spin | 1 pump | Amazon |
| Lauzic Washing Machine Water Inlet Valve | Fill and leak problems | Water inlet valve | Leaking water, incorrect filling | 1 valve | Amazon |
Detailed Reviews
1. WA50R5200AW/US WA50R5400AV/US Suspension Rods
Our pick — 4.5+★ from 500+ verified ratings; the strongest balance of quality and price.
Four stainless steel rods — that’s the pitch here.
If your washer is walking, banging, or flashing a DC code mid-spin, this set of four stainless steel suspension rods is the direct fix. It is the top-rated suspension set here — 4.5+ stars across 500+ ratings — and the reviews keep landing on the same point. What wins people over is that it simply works: the machine stops hopping and the balance comes back.
Fit is broad. This kit is listed compatible with the WA45H7000AW/A2 along with the WA400, WA456, WA45H, WA40J and WA45M series, and it cross-references a long run of factory numbers including DC97-16350U, DC97-16350S, DC97-16350E, DC97-05280U and PS11719937. Each rod measures 26.18 inches, so check that against your original before you order.
The honest part: rods are a wear item, and some of these sets fail early — a few owners had one give out inside six weeks. Treat the rods as consumable and don’t expect a forever part. Installation is a 20 to 30 minute job with a screwdriver once the power and water are off.
Where it earns its keep
- Stainless steel body built thicker and wear-resistant so it holds shape under spin stress
- Cross-references a wide spread of factory part numbers, so one kit covers many Samsung top-loaders
- Handles the full spread of balance symptoms — wobble, banging, DC codes
What to keep in mind
- Durability is the weak spot — a few sets fail inside six weeks
- 26.18-inch length must match your original or the tub loads unevenly
Reach for this if: your tub shakes, bangs, or throws a DC code and you want a top-rated 4-rod set.
Measure first: confirm your stock rod is 26.18 inches before you commit — a mismatch here is the one thing that ruins the fix.
2. DC97-16350U DC97-16350S DC97-16350T Suspension Rods
The compatibility list here is a phone book — one of the broadest in this group.
Anyone with an older or oddball Samsung top-loader knows the feeling of a part that “almost” fits. This Pulluty set sidesteps that by covering an unusually long roster of model numbers, from the WA45H7000AW/A2 and WA45H7000AW/AA through WA50R5200AW/US, WA50R5400AV/US, WA56-series machines, and the WA400PJHDWR/AA. It ships as four rods, and the build is described as meeting OEM manufacturing requirements without carrying the OEM badge.
How it works is mechanical and simple: each rod swings on a ball at one end and slides along the boom at the other, soaking up the vibration energy before it reaches the cabinet. That is the same shock-absorber job the factory rods do, and owners routinely report the whole machine settling into a smooth spin once the set is in. The kit replaces DC97-16350E, DC97-16350S, DC97-16350T, DC97-16350C and DC97-16350D.
Installation runs around 30 minutes, and the value math is obvious — it is a fraction of what a repairman charges for the same job. One thing to plan for: the four rods ship in a 27 x 3.75 x 3.75 inch box, so inspect them on arrival and confirm all four are present and straight before you start tearing the washer apart.
Best cross-reference reach: if your model number is obscure and other listings keep saying “does not fit,” this one is the safest bet — its compatibility roster is the broadest in the lineup.
The trade-off: you are buying OEM-equivalent, not genuine Samsung, so check the rods for straightness from the start before the install.
Pick it when: your washer’s model number keeps falling off other compatibility lists and you want maximum odds of a match.
Look elsewhere if: you need a specific measured length — this listing doesn’t state one, so measure against your original first.
3. WA45T3200AW/A4 WA45H7000AW/A2 WA50R5400AV/US Suspension Rods
Thicker, forged, and packaged heavy — the beefiest-feeling rod set of the bunch.
Where most suspension rods are stamped and assembled, the Vypart set forges the rod body at high temperature and claims a rod 1.5 times thicker than standard. In practice that means less bending and breaking under the stress of a full spin, which is exactly the failure that sends you back to the parts page. The set is built from premium steel and spring components and weighs 1.9 pounds at the package level.
Compatibility is wide and includes your WA45H7000AW/A2 alongside WA45T3200AW/A4, WA50R5200AW/US, WA50R5400AV/US, WA45H7200AW/A2, WA400PJHDWR and WA456DRHDWR/AA. It also serves as a replacement for DC97-16350E, DC97-16350T, DC97-16350C, DC97-05280W, DC97-16350U and DC97-16350D. Beyond wobble and noise, it is listed to help resolve the DC, UR, UB and UL error codes, which covers a lot of “my washer just stops and beeps” territory.
One quirk worth knowing before you open the box: the rods ship in two color batches, white and gold, assigned at random. Same part, same quality, different look on the rod head — nothing to worry about, just not a color you choose. The kit is one package containing all four rods, and install runs 25 to 30 minutes with a screwdriver and tape.
The real pull: that 1.5-times-thicker forged rod is the beefiest build claim in this group, and a sturdier shaft is what resists the bending that ends a worn rod’s life early.
The quirk: white or gold, chosen at random — cosmetic only, but if color matters to you, that is not something this listing lets you pick.
Worth it for: the buyer who has already replaced rods once and wants a heavier shaft this time around to stop the cycle from repeating.
One thing to expect: a random white or gold finish on arrival — same 4-pack, same material spec, just not a color you control.
4. WA45H7000AW/A2 WA45H7200AW/A2 WA45N3050AW/A4 Suspension Rods
The shorter rod in the lineup, for washers that want a 25.8-inch fit.
Length is where this set separates itself. These rods measure 25.8 inches, the shortest in this group and a touch under the 26.18-inch set at the top of the list. That sounds like a rounding error, but in suspension it is the difference between a tub that sits level and one that leans. If your original rods measure out to 25.8, this is the set that matches. The kit includes all four rods.
The build is a silver zinc alloy body with a shaft described as 15% thicker than standard, meant to resist the bending that throws a tub out of balance. The rods are lubricated from the factory for smoother movement, which cuts friction and the noise that goes with it. It replaces a broad list of factory numbers including DC97-16350E, DC97-16350U, DC97-16350T, DC97-05280H, DC97-05280V, DC97-05280W and DC97-05280X, and covers WA45H7000AW/A2 alongside WA45H7200AW/A2, WA45N3050AW/A4, WA422PRHDWR/AA, WA50T5300AC/US and WA400PJHDWR/AA.
Durability is a mixed bag on this one — the spring assembly is the part that gets worked hardest, and there is some report of breaking inside a month. Not the norm, but worth weighing if your washer runs long, hot, heavy cycles. The install is the standard 25 to 30 minutes, and gloves plus a disconnect at the wall are the preparation the listing asks for.
What stands out: the 25.8-inch length — an exact-fit size rather than the 26.18-inch standard.
The nag: spring durability is the question mark, so if you run heavy loads often, treat this as the fit-first pick rather than the longevity-first one.
The match for: a washer whose stock rods measure 25.8 inches and where getting the exact length right matters more than any other spec.
Weigh this: the springs are the hardest-worked part and durability chatter exists — fine for normal loads, less ideal for constant heavy cycles.
5. DC97-19289F DC97-19289B PX3516-01 Washer Drain Pump Assembly
For the washer that fills fine and then refuses to let the water go.
Standing water and a flashing F02 or E5 code is a drain-pump problem, not a rod problem, and this is the part that addresses it. The assembly replaces DC97-19289F, DC97-19289B, PX3516-01, DC97-19289A, DC97-17366A, DC97-17366J, DC97-17349B, AP6806651 and PS12592631. It handles the whole cluster of drain symptoms — water that won’t leave, a pump that won’t spin, leaks underneath, and noise from the tub area.
Fit is confirmed for the WA45H7000AW/A2 and WA45H7000AW/AA, plus the WA40J3000AW/A2, WA45H7000AP/A2 and WA48J7770AW/A2. Note the listing’s own warning: it is not a fit for every Samsung washer, so compare the pictures and part numbers against your unit before buying. The pump body is plastic and weighs 2.2 pounds, and it runs on corded electric power like the one it replaces.
Prep is small but real. The listing asks for pliers, a Phillips head screwdriver, black tape and gloves, and the usual disconnect at the power and water supply.
The one to grab if: the machine won’t drain, throws an F02 or E5, or leaks underneath — a classic drain-pump failure, not a suspension one.
Do this first: verify your exact model against the listing’s compatibility list, since it explicitly says it does not fit every Samsung washer.
6. Lauzic Washing Machine Water Inlet Valve
The valve behind your fill and leak problems — if water is the issue, this is the part.
When the washer fills wrong, drips at the back, or won’t bring in hot water, the water inlet valve is what regulates the cold and hot supply coming into the machine. This one fits an unusually long list of WA45H7000AW/A2 revisions — the /A2-00 through /A2-14 suffix codes are all listed, along with the /AA series and the WA400PJHDWR/AA, WA45M7050AW/A4, WA50R5200AW/US, WA50R5400AV/US and WA422PRHDWR/AA machines. If your washer’s sticker has a two-digit suffix, check the listing closely; the odds are good it is on there.
The unit is plastic with a female iron pipe connector, and it arrives as a single valve. It is a fill-control part, so the symptoms it fixes are specific: leaking water and incorrect filling. It does not address a no-drain or out-of-balance problem, which are separate parts on this list.
Here is the caveat to read before you install: while buyers report the valve fits and the washer runs well afterward, some of them also report leakage issues. That makes careful seating of the connections the critical step — an inlet valve that leaks is usually a fitting that is not tight, not a bad valve. Get the threads and connectors snug and dry, and this is a cheap way to fix a fill fault.
Buy this when: water is showing up where it shouldn’t or the fill is off — a leaking or misbehaving inlet valve is the culprit.
Watch for: leakage after install is the recurring report, so double-check that every connection is fully seated before you call it done.
Know the Specs
Rod Length and the 4-Pack Count
Length is the number that decides whether a suspension rod fits your tub. Two sets here are 26.18 and 25.8 inches — close enough to look the same in a photo, different enough to matter. Measure your original end to end. And every suspension set should have four rods, because one new rod among three worn ones leaves the tub tilted.
What “OEM-Equivalent” Means
OEM labels mean the part was built to the same factory spec; OEM-equivalent means a different maker built it to meet those requirements. On a wear item like a rod or pump, that usually means you pay less for the same job — but check the part for straightness and fit on arrival rather than assuming.
Which Error Code Points to Which Part
A DC, UR, UB or UL code during the spin cycle is an out-of-balance signal from the tub — that is rod territory. An F02 or E5 code with standing water points to the drain pump. Neither one should be treated as a general failure of the machine; each names a specific part to replace.
Part Numbers and Cross-References
The listing codes like DC97-16350U, DC97-16350E, DC97-05280W and DC97-19289F are factory numbers that cross-reference across Samsung’s lineup. Matching your old part number to the listing is more reliable than matching the model name alone.
Common Questions
How do I know if my washer needs suspension rods or a drain pump?
Will these suspension rods fit my WA45H7000AW/A2 washer?
How long does it take to replace washing machine suspension rods?
What do the DC, UR, UB and UL codes on my Samsung washer mean?
Is a drain pump or a water inlet valve the part I need for a leak?
Are aftermarket suspension rods as good as genuine Samsung parts?
Do I need to replace all four suspension rods at once?
What tools do I need to install these parts myself?
Why is my washer filling with the wrong temperature of water?
The Bottom Line
If your washer shakes, bangs, or throws a DC code (an error code the machine shows when it detects a fault), the wa45h7000aw a2 parts fix most people want is the WA50R5200AW/US suspension rod kit. It gives you four stainless rods and a 4.5+ star average across 500+ ratings. If your model number keeps failing other compatibility checks, grab the Upgraded DC97-16350U set for its broader coverage. If the problem is water rather than movement, the DC97-19289F drain pump handles a machine that won’t drain. The Lauzic inlet valve is the part for a fill or leak fault. Diagnose the symptom first, then match the rod length and part number, and you skip the service call.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of July 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.



