9 Best Troy Bilt Horse Tiller Parts | Oil Seals That Actually Fit

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

If your Horse tiller is leaking oil, slipping out of gear, or coughing at half throttle, the fix is usually one small part — and the hard part is buying the right one the first time. Every pick here is a direct replacement for a Troy-Bilt Horse model, with the part numbers spelled out so you can match your machine before you order.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

Below you’ll find seals, belts, gaskets, and tine sets sorted by the job they fix, plus the fit traps that catch most buyers. Every entry is a verified Troy-Bilt Horse tiller part, so you can skip the guesswork and get back to turning soil.

Top Picks

Replacement Kits Tiller Axle & Tine Seal Kit
Best OverallReplacement Kits Tiller Axle & Tine Seal Kit4.5+★400+ ratingsFour seals in one bag, and the leak stops before it reaches your tine shaft. Oil weeping around the axle is the most common reason a Horse tiller gets parked mid-season, and this kit covers both ends of the job at once.Check price on Amazon
Throttle Choke Cable GW-9015 Fit Troy Bilt Horse Tiller GW-9015 GW-9240 6HP Tecumseh Engines
Top PerformerThrottle Choke Cable GW-90154.5+★20+ ratingsWhen the lever flops loose and the engine only runs at one speed, this is the fix. A snapped or seized throttle cable turns a tiller into an on-off machine.Check price on Amazon
632230 Carburetor for Tecumseh H30 H50 H60 HH60 5HP 6HP Troy Bilt
Best Value632230 Carburetor4.5+★700+ ratingsA gummed-up carb is the number one reason a stored Horse won’t start in spring. This is a bolt-on carburetor assembly for the Tecumseh H30, H50, H60 and HH60 four-cycle engines that power many Horse tillers.Check price on Amazon

How To Choose The Best Troy Bilt Horse Tiller Parts

The single most common mistake with these parts is ordering by the name “Horse” alone. Troy-Bilt built the Horse across many years and several engine families, so a part that fits one machine can be the wrong size on another. Match the part number stamped on your old component first, then confirm the physical size.

Start with the part number, not the model name

Every listing here replaces a specific original number — GW-9621 for an axle seal, 632230 for a carburetor, 1901118 for a tine set. Write your old number down before you shop. If the number on the box matches the number on your machine, you are almost always in the clear.

Check shaft and bore sizes on seals and belts

A seal is only as good as its fit on the shaft. The axle seals here are built for a 1.000 inch diameter shaft in a 1.500 inch bore, while the tine seals step up to a 1.250 inch shaft in a 2.000 inch bore. Measure yours with calipers if the old part is too worn to read.

Know which parts actually wear out

Tines are the wearing part on a rear tine tiller — rounded edges stop biting into hard ground. Oil seals dry out and weep. Belts glaze and slip. Carburetors gum up from old fuel. Buy for the symptom you are actually seeing, not for a full rebuild you may not need.

Side-by-Side Comparison

Model Best For Replaces Part Key Size Weight Amazon
Replacement Kits Axle & Tine Seal Kit★ Best Overall Stopping oil leaks GW-9621, GW 9601, 921-04031, 240-804, 49-051 (axle); GW-9618, GW-9616, GW-9602, GW-9618099, 240-507, 49-050 (tine) 1.000″ shaft / 1.500″ bore — Amazon
Throttle Choke Cable GW-9015Top Performer Lost throttle control GW-9015, GW-9240 53-5/8″ cable 7.8 oz Amazon
632230 Carburetor for TecumsehBest Value Hard starting engine 632230, 632631 H30–HH60 engines — Amazon
LEIMO KPARTS Carburetor Broad engine coverage 632230, 632272 H30–HH70 engines — Amazon
Oregon 75-685 Belt Slipping drive belt Troy Bilt 1128-1 21-3/4″ x 1/2″ — Amazon
Tiller Fiber Reversing Disc Reverse gear slip GW-2732, 1072 1-1/4″ ID / 3-7/8″ OD 6.4 oz Amazon
Worm Gear Kit GW-11527 Tine shaft rebuild GW-11527, GW-1064 Bronze gear kit 2.18 lb Amazon
1901118 Tine Set 16 Piece Full tine rebuild 1901118, 10802 12″ bolo, 7/16″ hole 15.71 lb Amazon
16 Tiller Tines With Hardware Budget tine swap 1901118, 1901118A 12″ bolo, 3/8″ hole 17.2 lb Amazon

Detailed Reviews

★ Best Overall

1. Replacement Kits Tiller Axle & Tine Seal Kit

Our pick — 4.5+★ from 400+ verified ratings; the strongest balance of quality and price.

Four SealsAxle & Tine

Four seals in one bag, and the leak stops before it reaches your tine shaft.

Oil weeping around the axle is the most common reason a Horse tiller gets parked mid-season, and this kit covers both ends of the job at once. You get four seals total — two for the axles and two for the tines — so a full reseal happens in a single order instead of two.

Fitting is where this one earns its keep. The axle pair is sized for a 1.000 inch diameter shaft in a 1.500 inch bore, and the tine pair steps up to a 1.250 inch diameter shaft in a 2.000 inch bore. Measure both before you order, because a seal that is off by a fraction will weep again within weeks. The axle seals cross to GW-9621, GW 9601, 921-04031, 240-804 and 49-051; the tine seals cross to GW-9618, GW-9616, GW-9602, GW-9618099, 240-507 and 49-050.

Fit is what wins people over, along with a rubber compound that holds up against gear oil.. The crowd verdict backs it: It holds 4.5+ stars across 400+ ratings, strong for a replacement seal.. The honest catch is that it is a fit-critical part, so if your shaft has a wear groove, fresh rubber alone will not seal it.

What Lands Well

  • Full reseal in one kit — 2 axle seals plus 2 tine seals
  • Crosses to six original part numbers per side, so matching is easy
  • Stops the leak that otherwise drips onto the tine housing

Where It Asks For Care

  • You must verify 1.000″/1.500″ and 1.250″/2.000″ sizes yourself
  • A grooved shaft will still weep even with new seals

Buy this if: your Horse is leaving oil spots and you want the whole seal job done in one order.

Hold off if: you have not measured your shaft and bore yet — this part lives or dies on that number.

Top Performer

2. Throttle Choke Cable GW-9015

53-5/8″ Cable6HP Tecumseh

When the lever flops loose and the engine only runs at one speed, this is the fix.

A snapped or seized throttle cable turns a tiller into an on-off machine. This replacement restores the lever-to-carburetor link on Horse models running the 6 HP Tecumseh engine, and it crosses to the original GW-9015, 9015, GW-9240 and 9240 numbers.

The measurement to check is the cable run: 53-5/8 inches, with the inner cable at 57.5 inches. That is a different measurement from the 21-3/4 inch Oregon belt in this list, which is expected — one is a control cable running up the handlebar, the other is a drive belt.

This is a low-volume part, so the sample of owner feedback is thin compared with the carburetors and tine sets. Buy it on the part number and the length, not on popularity. One cautious note: it is listed for the 6 HP Tecumseh Horses, so a different engine family will need a different cable.

Fit-first buying: confirm GW-9015 or GW-9240 on your old cable and the 53-5/8 inch length, then order with confidence.

The real limit: it is built for 6 HP Tecumseh-equipped Horses, so check your engine before assuming it fits.

Reach for this if: your throttle lever has gone slack or the cable has frayed on a 6 HP Tecumseh Horse.

Look elsewhere if: your engine is a different size — the cable length is tied to that fitment.

Best Value

3. 632230 Carburetor

Full KitH30–HH60

A gummed-up carb is the number one reason a stored Horse won’t start in spring.

This is a bolt-on carburetor assembly for the Tecumseh H30, H50, H60 and HH60 four-cycle engines that power many Horse tillers. It replaces the 632631, 632230, 632272, 632235, 631067 and 631067A numbers, and it arrives without a built-in manual choke.

What you actually get is the reason to pick this one: the carburetor, an air filter, a shut-off valve, a fuel line, a spark plug, a gasket, a fuel filter and two clips in a single box. That is a running engine’s worth of small parts, which saves a second order and a second wait. Owners focus on performance, and the consensus is that these run clean once the idle is dialed in..

Two things to plan for. The idle mixture often needs a slight tweak after install — that is normal for an aftermarket carb and not a defect. And the inlet gasket has drawn some grumbles, so check it against your old one and use a fresh gasket if it looks thin. It holds 4.5+ stars across 700+ ratings, and most buyers report it bolting on and running..

Why it earns the spot: the accessory bundle — filter, line, plug, valve and clips — turns a carb swap into a one-box job.

Plan for this: expect to set the idle screw, and inspect the inlet gasket before you bolt it down.

Best match for: a Horse with a Tecumseh H30–HH60 that cranks but won’t catch after winter storage.

Think twice if: your engine is a different family — the fitment list stops at the HH60.

Most Versatile

4. LEIMO KPARTS Carburetor 632230

H30–HH70Wide Cross-List

The broadest cross-reference list of any carb here — one more engine family than the 632230 above.

Where the previous carburetor stops at the HH60, this one reaches the HH70 as well. It covers the Tecumseh H30, H50, H60, HH60 and HH70 four-cycle engines used on Horse tillers, and it also cross-lists John Deere and Sears applications.

The replacement numbers are the deep part: 632631, 632230, 632272, 631067, 632235, 631867, 632019A, 632019, 631828, 632076, 631067 and 631067A. If your old carb’s stamp is worn unreadable, there is a strong chance it appears on that list. The bundle includes the carburetor plus an air filter that replaces Tecumseh 30727, and the air filter alone fits the 3–8 HP vertical and horizontal LAV, H, HS, HH, VH, HM, V40-70 and HS30 series.

Owners mention these running straight from the start and reviving tired engines, with exact-replacement fit as the recurring theme.. The trade-off is that this is a carburetor, so fuel quality still governs how long it stays clean — drain the tank before storage or you will be back here next spring.

Why It Stands Out

  • Covers H30 through HH70, one family wider than the 632230 carb
  • Twelve replacement numbers listed, so a worn stamp is less of a dead end
  • Air filter included, replacing Tecumseh 30727

The Honest Limits

  • Still needs clean fuel to stay trouble-free
  • The reference list is long — verify your exact number rather than eyeballing it

Pick this one when: your engine is an HH70 or your old carb’s number is hard to read.

Skip it when: you already confirmed a plain 632230 fitment and want the simpler match.

Best Fit Reputation

5. Oregon 75-685 Replacement Belt

21-3/4″ x 1/2″Horse Models

A glazed, stretched belt turns a strong engine into a slipping, smoking mess.

This is the drive belt for Horse models, replacing the Troy Bilt 1128-1 number. It measures 21-3/4 inches long and 1/2 inch wide, which is the pair of numbers you match against your old belt before ordering.

Oregon’s main line is outdoor power equipment belts, and owners praise this one’s build quality most.. Fit runs a close second, with 1979 Horse 4-speed models called out specifically as a match. There is enough length in the adjustment range to tension it properly, and owners note it can be set for maximum adjustment rather than running out of travel.

Here is the contrast worth knowing: this belt measures 21-3/4 inches and the throttle cable above measures 53-5/8 inches, so do not confuse a drive belt measurement with a control cable measurement when you are cross-checking parts. The belt is straightforward rubber-and-cord construction — the catch is simply that a worn pulley will eat a new belt, so inspect the sheaves while you have it apart.

The case for it: a known Oregon part at a 21-3/4 x 1/2 inch size with a documented Horse fit, which removes most of the ordering risk.

The check to run: look at your pulleys before install — a scored sheave will shorten any new belt’s life.

Right for you if: your Horse is slipping under load and the old belt measures 21-3/4 by 1/2 inch.

Not for you if: your machine takes a different belt number — measure first, this one is size-locked.

Reverse Fix

6. Tiller Fiber Reversing Disc

1-1/4″ IDGW-2732

The small fiber disc that decides whether your Horse backs out of a tight row.

When reverse gets grabby or refuses to engage, the reversing disc is usually the worn part. This one replaces 1072, GW-1072, 2732 and GW-2732, and it is a single disc in the box.

The three measurements that matter are an inside diameter of 1-1/4 inches, an outside diameter of 3-7/8 inches and a thickness of 1/2 inch. At 6.4 ounces it is a light, compact piece — the throttle cable here lists 7.8 ounces, so you get a fair sense of how small a part this really is. The smooth curved faces are shaped to shed soil rather than pack it, which helps hold your set tilling depth and keeps the gearbox area clearer.

Compatibility stretches well beyond the Horse: it also lists MTD Cub Cadet, Craftsman, Bolens, Remington, Yardman, Yard-Machine, White, Huskee and Ryobi fitment. Installation is a no-special-tools job, but kill the engine and pull the spark plug lead first. The honest note is that this is a low-volume part, so buy on the part number and the diameter, not on review momentum.

Fitment spread: one disc covers ten brand families, so it is worth checking even if your machine is not badged Troy-Bilt.

Before you turn a bolt: engine off, plug lead off — reverse gear work happens with your hands inside the housing.

Choose it if: reverse has gone weak and you have confirmed the 1-1/4 inch ID disc on your machine.

Pass if: your symptom is forward drive slip — that points at the belt, not this disc.

Rebuild Essential

7. Worm Gear Kit

Bronze GearGW-11527

When the tine shaft stops turning but the engine still purrs, the bronze gear has stripped.

This is the tine shaft worm gear kit — the bronze gear that transfers drive into the tines. It replaces GW-11527, 11527, GW-1064 and 1064, and it is the part you buy when a Horse loses tine drive entirely.

At 2.18 pounds it is a substantial piece of metal, and that mass is the point: this is a load-bearing gear, not a wear shim. Because it is bronze, it is designed to be the sacrificial part in the gearbox — if something has to give, you want it to be this, not the shaft it rides on. That makes it a rebuild item rather than a routine tune-up part.

Fitment is the whole game here. Confirm your gearbox takes GW-11527 or GW-1064 before ordering, because a stripped gear and a broken shaft produce a similar symptom from the handlebars. Expect a real teardown: drain the gear oil, open the housing, and plan on fresh seals while you are in there — the seal kit above covers exactly that job.

Why It Belongs Here

  • Bronze construction puts the wear on the gear, not the shaft
  • Four replacement numbers cover the common Horse gearbox variants
  • Restores tine drive when the engine is still running fine

The Job It Demands

  • Gearbox teardown, not a bolt-on swap
  • Confirm GW-11527 or GW-1064 first — the wrong gear will not mesh

For the committed repair: you are already planning to open the gearbox and want the bronze gear in hand.

Not a first buy: if the shaft still turns, your problem is upstream — check the belt and seals first.

Best Tine Value

8. 1901118 Troy-Bilt Tiller Tine Set

16 Pieces12″ Bolo

Rebuild both sides of the tine shaft in one afternoon, bolts included.

Worn, rounded tines stop biting hard ground, and this set puts fresh steel on both sides of the shaft at once. You get sixteen bolo tines — eight left hand and eight right hand — which is enough to fully rebuild a Horse or Pony rear tine tiller.

The hardware is the part that saves a trip: 32 cap screws, 32 hex nuts and 32 lock washers all come in the box, plus cast iron hub holders so the set bolts up complete. Each tine measures 12 inches with a 7/16 inch mounting hole, and the three holes are spaced 2-5/8 or 3-1/8 inches center to center. Match that hole pattern against your old tines before you order — it is the one spec that decides whether this set goes on.

Owners rate value highest, with tilling performance close behind.. The honest catch is fit and hole spacing: some Horse II machines do not line up cleanly, and a few buyers have seen tines crack under heavy load. Treat this as a value-priced aftermarket set rather than an OEM duplicate, and it earns its place.

What you get for the money: sixteen tines plus the entire fastener count and hub holders, which is the difference between a rebuild and a scavenger hunt.

The catch to plan around: verify the 7/16 inch hole and the 2-5/8 or 3-1/8 inch spacing on your own shaft first.

Good fit for: a Horse or Pony owner rebuilding the full tine assembly on a budget.

Second thoughts if: you run a Horse II or till rocky ground — measure the spacing and expect to inspect for cracks.

Budget Tine Set

9. Tiller Tines With Hardware

16 Pieces3/8″ Holes

A full sixteen-tine swap for the owner who wants every tine replaced at once.

Same job as the set above, but with a different hardware spec: these bolo tines carry three 3/8 inch mounting holes rather than 7/16 inch. Each tine is 12 inches, with holes spaced 2-5/8 and 3-1/8 inches on center — the same pattern the original tines used.

The fasteners are included and specified: 3/8 inch grade 5 cap screws, zinc hex nuts and lock washers. Nothing extra to buy. The whole set lists 17.2 pounds against the 15.71 pounds of the set above, which is a fair read on thicker hardware. It replaces 1901118 and 1901118A, also cataloged as 1270-1A, 1270-2A and 10802.

Satisfied owners cite build quality and function, though value reviews split between strong deal and overpriced.. Fit is the recurring friction point, which is why the manufacturer states plainly that this is aftermarket, not OEM. Lay your old tines out in order before you start; the left and right hands alternate and curve toward each other, and that alternating pattern is what pulls soil to the center.

Worth a look if: your shaft takes 3/8 inch hardware and you want all sixteen tines replaced in one order.

Check first if: you have a Horse II — measure your hole spacing and diameter before committing.

Know the Specs

Shaft Diameter and Bore Size on Oil Seals

A seal is listed by two numbers: the shaft diameter it wraps around and the bore it presses into. The axle seals here are 1.000 inch shaft by 1.500 inch bore; the tine seals are 1.250 inch shaft by 2.000 inch bore. Measure your shaft with calipers — a seal that is too loose weeps, and one that is too tight will not seat. If the shaft has a visible wear groove, no seal will hold until the shaft is addressed.

Bolo Tine Hole Spacing

The mounting holes on a bolo tine are spaced on center, and that spacing is what decides fit. These sets list 2-5/8 or 3-1/8 inches center to center, with either a 7/16 inch or 3/8 inch hole depending on the set. Lay an old tine beside the new one and line up the holes before you start unbolting anything. Left and right hand tines alternate on the shaft, so keep them in order as you remove them.

Common Questions

How do I know which Troy Bilt Horse tiller parts fit my machine?
Match the part number stamped on your old component to the replacement numbers listed for each part. A Horse built across different years can carry different engines and gearboxes, so the part number is a far safer guide than the model name alone. If the stamp is worn, measure the physical size — shaft and bore on a seal, length and width on a belt, hole spacing on a tine — and compare that to the listing.
Are the axle and tine seals in the Replacement Kits set the same size?
No, and that is deliberate. The two axle seals are sized for a 1.000 inch diameter shaft in a 1.500 inch bore, while the two tine seals are larger at a 1.250 inch diameter shaft in a 2.000 inch bore. Measure both locations on your tiller before ordering, because mixing them up will leave one end leaking.
Will the 632230 carburetor fit my Horse if it has a different Tecumseh engine?
It is listed for the H30, H50, H60 and HH60 four-cycle engines, and the LEIMO KPARTS version extends that to the HH70. If your engine falls outside those families, the carburetor is unlikely to bolt on correctly. Confirm the engine model stamped on the block before you order, and cross-check your old carburetor’s number against the listed replacement set.
Why does my new carburetor need idle adjustment after installation?
Aftermarket carburetors commonly arrive with the idle mixture set approximately rather than tuned to your specific engine. A slight tweak of the idle screw after the engine warms up is normal and not a sign of a faulty part. If the engine runs rough at full throttle after adjustment, check the inlet gasket and the fuel filter that comes in the kit before assuming the carburetor is the problem.
How long should a replacement drive belt last on a Horse tiller?
Belt life depends heavily on the condition of your pulleys and how tight you run the tension. A scored or rusty sheave will wear through a new belt quickly, so inspect the pulleys while the belt is off. The Oregon 75-685 is 21-3/4 inches long and 1/2 inch wide, and owners note there is enough adjustment travel to tension it properly rather than maxing it out on day one.
What is the difference between the 7/16 inch and 3/8 inch tine sets here?
The mounting hole diameter and the fastener that goes through it. The 1901118 set uses a 7/16 inch hole with 32 cap screws, nuts and lock washers, while the Reliable Aftermarket set uses 3/8 inch holes with grade 5 cap screws and zinc hardware. Both list 2-5/8 or 3-1/8 inch hole spacing on 12 inch bolo tines. Measure the holes on your own shaft — that single number tells you which set will bolt on.
Can I replace just the tines without replacing the whole tine shaft?
Yes, and that is the normal approach when the shaft and gearbox are healthy. Both tine sets here replace all sixteen tines on the shaft, which is the practical option because tines wear at a similar rate. If the shaft itself is damaged or the bronze gear inside the gearbox has stripped, you are into a different job and will need the worm gear kit as well.
How do I tell a worn reversing disc from a slipping belt?
Check which direction is failing. If forward tilling pulls strongly but reverse is weak or refuses to engage, the reversing disc is the likely worn part — this one measures 1-1/4 inch inside diameter by 3-7/8 inch outside diameter. If the machine slips under load in forward, look at the drive belt instead. Doing both jobs at once is reasonable if the machine is already opened up.
Is the bronze worm gear meant to fail before other gearbox parts?
The gear is bronze, which is a softer metal than the steel shaft it drives, so it takes the wear rather than the shaft. That makes it the rebuild part when a Horse loses tine drive while the engine still runs. The kit replaces GW-11527, 11527, GW-1064 and 1064, and it weighs 2.18 pounds — a load-bearing component, not a shim. Plan on fresh seals while the gearbox is open.

The Bottom Line

For most owners chasing an oil leak, the troy bilt horse tiller parts pick that pays off first is the Replacement Kits Axle & Tine Seal Kit, because four seals covering both the 1.000 inch axle shaft and the 1.250 inch tine shaft fix the most common failure in one order. If the engine is the problem rather than the seals, the 632230 Carburetor arrives with the filter, fuel line, plug and gaskets included, which is a full tune-up in a box. And when the tines themselves are worn round, the 1901118 16 Piece Tine Set brings back the bite with every fastener and hub holder included.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top