Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
Crashing an X-Maxx is part of the fun — but a cracked shell is the one repair that actually stops you driving. The body you pick decides whether you stay bashed and painted or spend evenings trimming and spraying, and whether you ever fight a body clip again. Below are nine shells that genuinely fit the X-Maxx, sorted so you can pick in a couple of minutes.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
We cover what actually matters here: clear versus pre-painted, clipless versus body clips, and how much protection each shell adds. Read on for the traxxas x maxx body options that survive a bad landing.
Top Picks


How To Choose The Best Traxxas X Maxx Body
The first decision is clear or pre-painted. A clear shell is a blank canvas — you get exactly the colour scheme you want, but you supply the paint, the masking and the trimming hours. A pre-painted shell arrives ready to bolt on and gets you back to bashing the same afternoon.
Clear Or Pre-Painted
Clear polycarbonate shells are lighter on the wallet and give you full creative control, and they usually ship with window masks and decals so the masking line is already cut for you. Pre-painted shells cost more but delete the whole painting weekend. If you have never painted a lexan body, a factory-finished shell is the lower-risk route.
Clipless Versus Body Clips
Traditional X-Maxx bodies pin on with four body clips, and those clips are the small parts you lose in grass. Clipless bodies latch through a mount system instead — no loose pins, and you can pull the shell off with a quick release when you need to check the motor or swap a battery.
How Much Protection You Want
Every shell here is a 1/5-scale cover for the X-Maxx chassis, and some are sold whole-assembled with front and rear body mounts, a rear body support, roof skid plates and a tailgate protector. Those extra pieces matter most if you land on the roof or the tail — that is where the shell takes the hit. A bare shell keeps the spend down but leaves you reusing your existing hardware.
Side-by-Side Comparison
| Model | Best For | Finish | Mounting Included | Material | Amazon |
|---|---|---|---|---|---|
| Traxxas X-Maxx Body Set, Clear | Custom paint jobs | Clear, unpainted | Shell only | Polycarbonate | Amazon |
| Pro-Line 2021 Ram 1500 TRX Clear Body | Truck-style scale builds | Clear, pre-cut | Shell only | Polycarbonate | Amazon |
| Traxxas Rock n’ Roll Body | Fully assembled, lightest fit | Painted, decals applied | Assembled with tailgate protector | ABS | Amazon |
| Green X-MAXX Ultimate Clipless Body | Clipless convenience | Pre-painted, ready to mount | Body mounts, roof skids, tailgate | Plastic | Amazon |
| Blue X-MAXX Ultimate Clipless Body | Blue colour scheme | Pre-painted, ready to mount | Body mounts, roof skids, tailgate | Plastic | Amazon |
Detailed Reviews
1. Traxxas X-Maxx Body Set, Clear
A clear, unpainted polycarbonate shell that lets you build a one-off X-Maxx colourway.
If you enjoy the build as much as the driving, this is the shell to start with. It is a clear, unpainted polycarbonate (a tough, flexible plastic that flexes instead of shattering) X-Maxx body sold as an O.E.M. part, so it fits the truck’s own mounting points without drilling guesswork. You get the shell, X-Maxx decals and window masks in the box — the masks save you from freehanding the glass outlines with tape.
The polycarbonate is the reason it stays in one piece through rollovers. Where a stiffer shell can crack at the mounting holes, this material gives and springs back. It weighs in at 2.1 pounds, and it is the same figure as the ProGraphix body below, so the choice between those two really is about finish, not heft.
Now the honest part: clear means you buy paint separately, and you will spend an evening masking windows and trimming the wheel arches before it ever touches the truck. That is the trade for a one-off colourway. If you want to drive tomorrow, pick a factory-painted shell instead — the assembly work is already done for you there.
What sells it
- Polycarbonate shell that flexes through rollovers instead of cracking
- Window masks and X-Maxx decals included, so masking lines are pre-cut
- O.E.M. fit means it drops onto the stock mounting points
- 2.1 pounds — the same weight as the ProGraphix body
Where it asks more of you
- You supply and apply the paint; the shell arrives unpainted
- Trimming and masking add an evening before first run
- Shell only — body mounts are not part of the kit
Reach for this if: you want full control of the colour scheme and don’t mind an evening with masking tape and a spray can.
Think twice if: you want to be bashing this weekend — a pre-painted shell gets you there without the paint work.
2. Pro-Line Racing 2021 Ram 1500 TRX Clear Body
An officially licensed 2021 Ram 1500 TRX shell that gives the X-Maxx a real off-road truck silhouette.
Most X-Maxx shells are Traxxas’s own shape. This one is an officially licensed 2021 Ram 1500, made in the USA from crisp polycarbonate, so you get the actual TRX silhouette on a 1/5 chassis. If you like scale realism — a body that looks like a truck rather than a generic basher shell — this is the standout on the list.
You skip the wheel-arch cutting that eats an afternoon because Pro-Line trims this body at the factory. That pre-cut finish is what separates it from the Traxxas clear body above. Set against the Blue Clipless X-Maxx body, the size difference is obvious: this one measures 27.3 x 10 x 4 inches while the Blue Ultimate runs 36 x 22 x 8.13 inches, a 32% larger footprint on the clipless shell. That smaller footprint is the low-slung truck profile, not a fit problem.
What it does not do is save you the paint work — it is a clear shell, so you still prime, mask and spray. Body mounts are not in the box either, so you reuse the stock hardware. Buy this for the look, not for convenience.
The scale payoff: a licensed Ram TRX shape on your X-Maxx chassis — a genuinely different look from the factory shells, and pre-cut so the trimming is already done at the factory. It is made in the USA from crisp polycarbonate.
The honest catch: it still arrives clear, so paint, masking and window work are on you, and the box holds the body only — no mounts.
Choose it for the silhouette: scale-truck fans who want a real Ram TRX outline and would rather paint than trim.
Pass it by if: you have no interest in spraying a shell — everything here waits on your paint work.
3. Traxxas X-Maxx ProGraphix Body
The half-way house — pre-printed graphics, but you still choose your base colour.
Traxxas’s ProGraphix shells arrive with the graphics already printed on the lexan, so you paint only the base colour behind them. That splits the difference neatly between the fully clear Body Set and a fully finished factory shell. It ie protector, so you bolt it on and drive. The model name lists it for both the X-Maxx and X-Monster, and it is built from ABS (acrylonitrile butadiene styrene — a rigid moulded plastic) rather than the flexible polycarbonate the clear shells use.
The weight is the headline. At 1.6 pounds it is 0.5 pounds lighter than the Traxxas clear Body Set’s 2.1 pounds — a 31% lighter shell, which is mass sitting high on the chassis. Less mass high on the chassis means the truck tips less eagerly in a hard corner and lands with less weight to throw around.
The trade-off is the material. ABS is stiffer than polycarbonate, so it does not flex the same way when you roll. That is the case for the tailgate protector and the assembled mounts doing their job — the protection is the point with this shell.
The grab-and-go play: painted, decalled, assembled with a tailgate protector, and 1.6 pounds on the scale — the lightest here and 0.5 pounds under the clear Body Set’s 2.1 pounds.
What to know going in: ABS is the rigid moulded plastic, not flex-friendly polycarbonate, so a hard roll hits stiffer than on a lexan shell.
For the impatient basher: you want the truck back out today with zero paint work and the lightest shell available.
Where it gives something up: the stiffer ABS build trades some of the polycarbonate shells’ flex on heavy rollovers.
4. Traxxas 7811G X-Maxx Pre-Cut Body
A pre-painted shell that latches onto its own mount system instead of pinning with four body clips.
You never chase a body clip across the lawn again because the Ultimate Clipless body latches onto its mount system instead of pinning with four clips. It ships pre-painted and ready to mount with decals, an internal body support, roof skid plates, a tailgate protector and the body mounts themselves. That is the most complete hardware list on this page.
The roof skid plates are the detail that earns their keep. They guard the panel that grinds first when you land upside down, and the internal body support keeps the shell from flexing at the base of the roof. It is listed at 1.71 pounds and is built for the X-Maxx specifically.
One thing to plan for: the clipless system only works with its matching mount hardware, so this is not a shell you drop onto an old clip setup. You are committing to the clipless ecosystem. The green finish is fixed, too.
The pit-lane win: clipless latching with roof skid plates, internal support, tailgate protector and mounts all in the box — the most protection bundled into any shell here.
The ecosystem note: clipless means committing to its own mount system; it will not fit onto a clip-style setup.
Pick it when: you want to end the body-clip hunt and protect the roof at the same time.
Skip the switch if: your truck runs clip mounts and you have no plans to swap the hardware.
5. Blue X-MAXX Ultimate Clipless Body
Identical to the green clipless shell, but in blue — and 0.02 pounds lighter on the scale.
Same clipless latch, same hardware bundle: decals, internal body support, roof skid plates, tailgate protector and body mounts. If the green Ultimate does everything right and you just want a different colour on the truck, this is the swap. It comes pre-painted and ready to mount, so the body-clip hunt ends the day it arrives.
The blue shell weighs 1.69 pounds against the green’s 1.71 pounds. That is a rounding of the scale rather than a handling difference — you will not feel 0.02 pounds. The real numbers are the footprint: this is one of the two 36 x 22 x 8.13-inch shells on the page, alongside the green, versus the Pro-Line TRX at 27.3 x 10 x 4 inches.
The clipless mount system is a closed ecosystem, so check your truck is set up for it before you order. Colour is the only thing separating this from the green version.
The colour-matched full kit
- Clipless latch — no body pins to lose
- Roof skid plates and internal body support included
- Tailgate protector and body mounts in the box
- 1.69 pounds; 36 x 22 x 8.13 inches
What it locks you into
- Requires the matching clipless mount setup, not clip pins
- Blue finish is fixed, so no custom colour choice
- The weight difference versus the green shell is negligible
Suits a blue truck: you want the clipless hardware bundle in a colour that matches your build.
Only look elsewhere if: your chassis runs clip-style mounts or you want a different body colour.
6. Traxxas 7811R X-Maxx Pre-Cut Body
Clipless Mounting
Traditional bodies pin on with body clips, the small parts that vanish in grass. Clipless bodies use a latch and mount system instead, so there are no loose pins. The catch is that clipless only works with its own matching mounts, so it is a commitment rather than a bolt-on upgrade for a clip-style truck.
Body Support And Skid Plates
An internal body support stiffens the shell at the base of the roof so it does not flex on a hard landing. Roof skid plates sit on the panel that grinds first when the truck lands upside down. A tailgate protector covers the rear panel that scrapes on jumps and rollovers. Not every shell includes these, so check the bundle before you buy.
Polycarbonate Versus ABS
Polycarbonate is the flexible plastic that bends and springs back rather than cracking, and it is what most of the clear shells here use. ABS is a rigid moulded plastic — stiffer and less forgiving on a heavy roll, but it holds its shape. Weight follows the material and the trim: shells on this page run from 1.6 to 2.1 pounds.
Common Questions
Will these bodies fit my Traxxas X-Maxx without modification?
What is a clipless X-Maxx body and why does it cost more effort to switch?
Is a clear body or a pre-painted body the better buy?
What paint do I need for a clear polycarbonate X-Maxx shell?
Do I need to trim a pre-cut body?
What does a tailgate protector actually protect?
How much does X-Maxx body weight actually matter?
Is the Pro-Line Ram 1500 body smaller than the X-Maxx Ultimate body?
Can I put an X-Maxx body on an X-Monster or other Traxxas trucks?
Will replacing the shell change how my X-Maxx drives?
The Bottom Line
The shell that does the most for most X-Maxx owners is the Traxxas X-Maxx Body Set, Clear — genuine polycarbonate, an O.E.M. fit on the stock mounts, window masks and decals in the box, and 2.1 pounds. It asks for paint and an evening of masking, but it gives you a truck that looks like nobody else’s.
Want the colour chosen for you without paint work? The Rock n’ Roll body arrives painted, decalled and assembled at 1.6 pounds, the lightest here. Want to end the body-clip hunt? The Green X-MAXX Ultimate Clipless Body is the pick. And if you are building a scale truck, the Pro-Line Ram 1500 TRX is the one that turns heads.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.


