Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your TOTO is running, hissing, or refusing to flush clean, the fix is almost always one small part inside the tank — not a new toilet. The trick is buying the right one, because TOTO build their tanks around specific part numbers and a near-fit will leak or whistle. Below you will find the nine replacements that actually match TOTO toilets, sorted by what each one fixes.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Every part here is matched to a real TOTO tank, so you can stop guessing which valve or flapper your bowl takes. Here is the honest shortlist of the best Toto replacement parts for a running, leaking, or noisy tank.
Top Picks



How To Choose The Best Toto Replacement Parts
The single biggest mistake buyers make is ordering the part they can see failing rather than the part that is actually causing the problem. A toilet that never stops running is usually a fill valve issue, not a flapper issue. Do the two-minute diagnosis first, then buy.
Find the tank model number before anything else
TOTO stamps a model number inside the tank lid or on the tank wall — something like ST743S or ST412M. That number decides whether a flush valve, a handle, or a fill valve will simply drop in. A part listed as fitting “most TOTO toilets” is doing you a favour with adjustability, but a model-specific part saves you the guesswork entirely.
Match the inlet size, not the photo
The inlet connection is the threaded fitting where your water supply line meets the valve. Most TOTO fill valves use a 7/8 inch inlet, which is written as 0.88 inches in the specs. If your supply connector is a different size, even a genuine part will not seal, and you will be fighting a drip that has nothing to do with the valve’s quality.
One-piece and two-piece tanks take different valves
A one-piece toilet has the tank moulded into the bowl, and its flush valve drops through a 3 inch hole. A two-piece tank usually takes a smaller assembly with a mounting nut. Buying a one-piece valve for a two-piece bowl is the most common returns reason in this category, so read that line twice.
Side-by-Side Comparison
| Model | Best For | Part Type | Compatibility | Key Spec | Amazon |
|---|---|---|---|---|---|
| TOTO Adjustable Replacement Fill Valve★ Best Overall | Stopping a tank that runs and hisses | Fill valve | All TOTO toilet tanks | 7/8 inch inlet | Amazon |
| Genuine TOTO Korky 528GT Fill ValveLongest Adjustability | Replacing a tired fill valve with room to adjust | Fill valve kit | Replaces TSU99A.X and most TOTO valves | 8-1/2 to 14 inch height | Amazon |
| TOTO Combo Kit Flapper & Fill ValveComplete Tank Fix | One order that covers both wear parts | Flapper + fill valve | Replaces THU499S flapper | 2 pieces, adjustable flow | Amazon |
| FinFuture 3 Inch Flush Valve | One-piece tanks leaking at the flapper seal | Flush valve | TOTO THU440-1, THU460.6d, THU338-N, THU445.10F | 3 inch inlet and outlet | Amazon |
| TOILTOBLE THU224 Flush Valve | Aquia two-piece tanks with weak flushing | Dual flush valve | Aquia ST412M / ST413M / ST416M | 2 inch outlet | Amazon |
| Hygie Rinse SS114 Elongated Seat | Quiet, slam-free seating on an oval bowl | Toilet seat | SS154, SS113, SS114, SS224 and more | 18.5 inch elongated | Amazon |
| TOTO THU9476 Deodorizer Filter | Washlet owners chasing a lingering smell | Deodorizer cartridge | Washlet C100/C200/S300e/S350e | Activated carbon | Amazon |
| TOTO THU337#CP Push Button | MS654 owners with a sticking dual-flush button | Push button | MS654 | Polished chrome | Amazon |
| iFealClear Side Mount Handle & Flapper | One trip for a broken handle and a worn flapper | Handle + flapper kit | ST406, ST707, ST454E, ST743E, ST743S | 3 inch flapper | Amazon |
Detailed Reviews
1. TOTO Adjustable Fill Valve Assembly
Our pick — 4.5+★ from 750+ verified ratings; the strongest balance of quality and price.
The genuine TOTO valve that ends the hiss, the phantom refill, and the midnight drip.
If your tank keeps topping itself up long after the flush, this is the part you want. It is a real TOTO fill valve — manufacturer part number TSU99A.XR — so what arrives is the same piece the factory put in. TOTO make it adjustable for all TOTO toilet tanks, which means the fill height and the shut-off point are set by you rather than baked in at the factory.
Installation is the reason this is the top pick. The valve comes complete with the refill tube, the clamp, the cone washer, and the nut, so you are not halfway through the job hunting for a washer. The water supply connects to a standard 7/8 inch inlet, listed as 0.88 inches, which is the size most TOTO supply lines already use. The metal fittings resist hard-water corrosion better than the all-plastic parts on cheaper aftermarket valves.
What wins people over is the refill cycle: it shuts off cleanly and refills the tank at a steady rate. The recurring gripe is on the long-term side: some units stop sealing cleanly over time, and a few buyers never fully cured a slow leak. Size that honestly. A fill valve is a moving wear part, and that’s the nature of the job — but if your tank is currently flooding past the overflow tube, adjust the height before you screw the lid back on, because that setting is what separates a perfect install from a constant trickle.
What it does well
- Genuine TOTO part, not a copy — manufacturer part number TSU99A.XR
- Everything you need in the box: valve, refill tube, clamp, cone washer, nut
- Adjustable for every TOTO tank, so the fill height suits your bowl
- 7/8 inch (0.88 inch) inlet matches most standard TOTO supply lines
Where it asks for care
- The fill height must be dialled in by hand — set it too high and the tank overflows the tube
- It is a wear part; some units develop a slow leak as they age
Grab this one if: your TOTO runs on, hisses, or refills itself at random — this is the part behind all three.
Look elsewhere if: your problem is a flapper that won’t seat, because that’s a different piece entirely.
2. TOTO Korky 528GT Fill Valve Assembly
A fill valve that stretches from 8-1/2 to 14 inches, so an odd tank height is no problem.
Tall tanks and deep bowls are where this valve earns its keep. The height adjusts anywhere from 8-1/2 inch to 14 inch, which covers the tanks that a fixed-height valve simply can’t reach. It is built to replace TOTO part TSU99A.X and works across the rest of the TOTO fill-valve range, including the TSU18A, TSU36A, TSU09A, TSU17A, TSU30A, TSU31A and TSU13A — that’s a wide spread of older models from one box.
Here is the direct comparison that matters: the TOTO valve above ships with a 7/8 inch inlet, and this one reaches 14 inches in overall height. Those are different measurements doing different jobs, so match the one your tank actually calls for. If you have a deep tank, this is the safer bet. If you have a standard-height tank with a 7/8 inch supply line, the first pick is the tighter fit.
Owners find it installs in minutes and restores a normal flush. Be aware of two honest quirks. Some buyers report it is louder than the valve it replaced, and a few end up with a leak they never quite cured — usually a fill-height or supply-connection issue rather than a defective part. It also carries a 5 year warranty, which is more backing than you’ll get on most of the copies in this category.
Where it shines: that 8-1/2 to 14 inch adjustment range is the widest on this list, and the 5 year warranty is real reassurance on a moving part.
The honest note: it can run a little louder than the genuine TOTO valve, so if your bathroom is right beside a bedroom, that’s worth knowing.
Reach for this if: your tank is unusually tall and needs the extra reach.
Think twice if: quiet operation matters more to you than adjustability — the standard TOTO valve is the softer listen.
3. TOTO Combo Kit Universal Flapper
Two wear parts, one order, so you don’t have to work out which one is failing.
Nobody wants to pull the tank lid twice. This kit ships a genuine TOTO universal flapper, which replaces THU499S, alongside a genuine TOTO fill valve — two pieces, both rubber and stainless steel, both from the maker. The flapper is adjustable in height and the valve is adjustable in flow rate, so you can tune the flush volume to your bowl rather than accept a factory setting.
The pitch here is completeness. Instead of buying the flapper now and discovering the valve is also tired next weekend, you replace both in a single sitting. That one-order approach is exactly what makes a tank feel restored rather than patched. Owners mention their toilets flushing like new again, and the adjustable flow rate suits low-flush models especially well.
The trade-off is that you may be buying a part you didn’t strictly need. A slow leak after fitting does come up occasionally, which almost always traces to the flapper not seating flush against a mineral-crusted opening. Wipe the rim before you clip the new one in.
Why the combo works
- Genuine TOTO flapper and fill valve together — 2 pieces, no mixing brands
- Adjustable flow rate lets you dial in the right flush volume
- Adjustable flapper height suits different tank openings
- Saves a second order and a second tank-lid removal
Before you commit
- You pay for two parts even when only one has failed
- A dirty or crusted flapper seat can cause a slow leak that looks like a bad part
Best for: anyone with an older TOTO tank who wants to reset every wear part in one go.
Skip if: you have already replaced the fill valve recently — buy the flapper on its own instead.
4. FinFuture Toilet Flush Valve for 3 Inch Flush Hole
Built for one-piece tanks with a 3 inch hole — and it goes in without lifting the tank off the bowl.
One-piece toilets are the awkward ones, and this valve is shaped for them. The inlet and outlet both measure 3 inches, matching the flush hole in a one-piece tank. It fits TOTO THU440-1, THU460.6d, THU338-N and THU445.10F, so check your tank’s part number against that list before ordering. It is not compatible with two-piece toilets — that single line rules out half the shoppers, and it’s worth reading twice.
The installation story is where this beats the THU224 below. That valve suits two-piece Aquia tanks and, on some models, requires you to pull the tank to swap the button. This one installs in less than 20 minutes with no tank removal at all. For a one-piece bowl, that difference is the whole job.
Materials are a mix of durable plastic, 304 stainless steel and a silicone seal that is chemical resistant and won’t warp. The overflow tube is cuttable to length, so you set it to your tank instead of hoping the factory length matches. Owners consistently point to the silicone seal holding without leaks and shutting off cleanly. If yours still drips after fitting, the cut on the overflow tube or a bit of grit on the seal is the place to look first.
What you’re buying: a 3 inch flush valve with a chemical-resistant silicone seal and a cut-to-fit overflow tube — the parts that actually stop a tank from leaking.
The catch: it will not fit a two-piece toilet, so this is a one-piece-only purchase.
Made for: one-piece TOTO tanks listed under THU440-1, THU460.6d, THU338-N or THU445.10F.
Not for: two-piece bowls — the 3 inch geometry won’t seat.
5. TOILTOBLE THU224 Flush Valve Assembly
The Aquia answer — a half-flush-and-full-flush valve sized for TOTO’s two-piece tanks.
Aquia owners have a narrower field to choose from, and this valve is aimed straight at them. It fits two-piece TOTO Aquia new style, old style, Aquia II and Aquia III tanks, with model numbers CST414M and tanks ST413M, ST416M and ST464M called out specifically. It gives you full and half flush options, which is how you save water without giving up a strong flush when you need one.
Measure before you click, because this valve has hard limits. It only suits split-type (two-piece) toilets, never one-piece models. Your tank height has to be greater than 11.81 inch, and the total assembly stands 12 3/8 inch tall. The outlet is 2 inches. Compare that to the FinFuture above, which is built around a 3 inch hole for one-piece bowls — different tank, different valve, no crossover.
For THU224 swaps, you don’t remove the tank; you replace the upper section only. Other model numbers in the same family, like THU435, need the tank off and the button replaced. The body is ABS with silicone rubber gaskets, reinforced for durability. Functionality draws a mixed read overall, so treat the tank-height measurement as non-negotiable rather than a suggestion — wrong sizing is what causes poor flushing, not the valve itself.
The build: ABS body with silicone gaskets and a reinforced design, plus dual full and half flush settings that restore water savings.
Measure first: the tank must be taller than 11.81 inch and the assembly stands 12 3/8 inch — get that wrong and the flush suffers.
Suits you if: you own an Aquia two-piece tank that needs its THU224 upper section replaced.
Pass on it if: you have a one-piece bowl or a tank shorter than 11.81 inch.
6. Hygie Rinse SS114 Toilet Seat
A soft-close lid that lowers itself, so the 3 a.m. flush stops waking the house.
This is the only pick here that isn’t inside the tank, and for a lot of TOTO owners it’s the upgrade that actually changes daily life. The seat and lid lower slowly on a built-in soft-close hinge, which kills the slam. It also takes the wear off the seat and protects fingers from getting caught in a falling lid. The 18.5 inch length is the elongated oval shape, so make sure your bowl is oval rather than round.
Fit is the thing to get right. It replaces SS154, SS113, SS114, SS224, SS204, SS214 and SS124 seats, and the mounting hole spacing is 5.5 inches. The seat is high-impact glossy polypropylene with a stain-resistant surface, and four thickened pads sit underneath to keep it from shifting. Two screw options come in the box — a white plastic screw from below or a black expansion bolt from the top — so you can pick whichever your bowl allows.
It’s the crowd favourite of the whole list: the seat fits TOTO bowls cleanly, installs in minutes, and the finish looks like original equipment. It’s also the easiest item here for one person to handle alone — no water supply, no tank lid, no drips.
What earns it a spot
- Soft-close hinge lowers the lid slowly — no slam, no pinched fingers
- Replaces SS154, SS113, SS114, SS224, SS204, SS214 and SS124 seats
- 18.5 inch elongated fit with 5.5 inch mounting hole spacing
- Two screw types included, so top-mount and bottom-mount bowls both work
Check before ordering
- Elongated only — it will not suit a round bowl
- Polypropylene, not a moulded or wooden seat, so it has a lighter feel
Worth it for: anyone with an oval TOTO bowl and a slamming lid they’re tired of hearing.
Double-check first: your bowl shape and your mounting hole spacing, because elongated seats won’t fit a round bowl.
7. Replace OEM TOTO THU9476 Deodorizer Catalyst Cartridge
The small cartridge that decides whether your Washlet smells fresh or stale.
If your bidet seat has started leaving a faint smell in the bathroom, the deodorizer cartridge is the culprit — it’s a consumable, and it wears out. This one replaces the TOTO THU9476 catalyst, and it fits Washlet S300e, S350e, C100 and C200 models, plus SW2034T20, SW2044T20, SW2043, SW2043R, SW2044, SW573, SW574, SW583 and SW584.
The material is coal-based activated carbon, which is a porous material with a vast network of micro-pores and a large surface area for trapping odour molecules. That’s the whole mechanism behind it. There are no fragrances and no additives in the cartridge, so it neutralises rather than masks, which suits a bathroom where you’d rather not have a perfume smell sitting on top of the problem.
Replacement is quick and the fit is right, which is the main thing with a cartridge like this. The split opinion here is on value — some buyers feel the cost per cartridge is high for what is essentially a small block of carbon. That’s a fair position, and if it bothers you, stretching the interval between changes by keeping the bathroom ventilated is the sensible compromise.
What it does: replaces THU9476 in the Washlet range, using fragrance-free coal-based activated carbon to trap odour rather than cover it.
The honest trade-off: value is the divisive point — it is a consumable, so it will need buying again.
Buy this if: you have a S300e, S350e, C100 or C200 Washlet and the bathroom has started to smell faintly of the last visitor.
Not needed if: your Washlet is outside those model numbers — check the seat’s own part list first.
8. TOTO Dual Flush Push Button THU337
A genuine TOTO push button for the MS654 — the part that gets sticky after years of thumbs.
When the flush button on a dual-flush TOTO starts needing two or three presses, the button assembly is worn and no amount of pressing harder will fix it. This is the genuine TOTO push button, part THU337#CP, in polished chrome. It’s a brand-specific and model-specific part built for the MS654, assembled from metal with a push-pull mechanism and an ambidextrous orientation, so it fits either hand.
Quality is what stands out here. The metal construction and polished chrome finish mean it holds its shine and its action far better than the plastic knock-offs that turn chalky in a hard-water bathroom. It’s an easy install for anyone comfortable with the tank lid off, and the push action comes back crisp once it’s seated properly.
The one thing to be clear about is fit. This is not a universal button — it is tied to the MS654, and if your model number is different, it won’t line up. That model-specific nature is the price of getting a genuine part with the right thread and the right travel. Check the number on your tank before ordering and the install is straightforward.
The strong point: genuine TOTO THU337#CP in polished chrome with a metal push-pull mechanism — it restores a crisp, one-press flush.
Know this: it fits the MS654 specifically, so it isn’t a one-size button.
This is your part if: you own an MS654 and the flush button has gone soft or sticky.
Don’t order it if: your TOTO is a different model — the fit is model-specific.
9. iFealClear Side Mount Toilet Handle Lever with 3″ Flapper
A copper lever and a 3 inch flapper in one box, for the two parts that fail together.
A handle that jiggles and a flapper that won’t seal usually show up in the same week, because they wear at the same rate. This kit bundles a copper side-mount trip lever with a rubber flapper and a chain — three pieces, one job. The lever is right-hand oriented, so check which side your handle sits on before ordering.
The handle fits ST406, ST707, ST454E, ST743E, ST706 and ST743S toilets, replacing THU068#CP. The flapper is built for a 3 inch flush valve, matching THU138S and fitting ST743S, ST744S, ST754SF, ST764S, ST774S, ST784SF, ST94SF, ST814S, CST756204SF, SCT853S and CST845S. That’s a long list, and it’s worth scanning it rather than assuming your model is included.
The copper lever gives a solid, firm action instead of the loose plastic feel of cheaper handles. Owners highlight the fit on ST406, ST707 and ST743S tanks and the firm lever action. The body of the handle runs about 5 to 8 inches, so look at your tank’s side profile if space is tight. If your flush still dribbles after fitting, the usual fix is shortening the chain a link at a time until the flapper seats cleanly.
What’s in the box for you
- Copper side-mount lever, rubber flapper and chain together — 3 pieces
- Handle fits ST406, ST707, ST454E, ST743E, ST706 and ST743S
- Flapper matches a 3 inch flush valve and THU138S
- Copper lever gives a firmer action than plastic
Worth weighing up
- Right-hand mount only, so left-side handles won’t work
- The chain needs shortening to fit — too long and the flapper never seals
Pick this up if: your handle wobbles and your flapper is past its best, and you’d rather fix both in one go.
Give it a miss if: your handle is on the left side of the tank or your model isn’t on the fit list.
Know the Specs
Inlet connection size
The inlet is the threaded fitting where your water supply line screws onto the fill valve. A 7/8 inch inlet, written as 0.88 inches, matches the supply connector on most standard TOTO tanks. Get this wrong and the valve itself may be perfect but the joint will drip. It’s the smallest measurement on this page and the one that causes the most returns.
3 inch versus 2 inch flush holes
The flush hole is the opening the valve drops through at the bottom of the tank. One-piece tanks commonly use a 3 inch opening, while two-piece assemblies like the Aquia run a 2 inch outlet. Buying the wrong geometry is the single most common fit failure in this category — the number has to match your tank, not the valve’s reputation.
Fill valve height and tank height
Fill valves come in fixed or adjustable heights. An adjustable valve, like the Korky 528GT, spans 8-1/2 inch to 14 inch so it can suit deep tanks. For a flush valve, the tank has to clear a minimum height — the THU224 needs a tank greater than 11.81 inch. Measure the inside of the tank from the base to the rim before ordering any valve with a height limit.
Flapper size and seat condition
A flapper is the rubber seal that drops onto the flush opening to hold water in the tank. A 3 inch flapper needs a 3 inch opening, and the seat it drops onto has to be clean. Mineral crusting on the seat is what causes most “new flapper still leaks” cases. Wipe the rim before you clip a fresh one in and the seal usually holds.
Common Questions
Will a universal TOTO fill valve fit my specific tank model?
How do I stop my TOTO toilet from running constantly?
Can I use a 3 inch flush valve in a two-piece TOTO toilet?
How long does a TOTO fill valve or flapper last?
Do I need a genuine TOTO part or is a compatible one fine?
How do I know if my TOTO toilet is one-piece or two-piece?
Why does my new flapper still leak?
How often should I replace a Washlet deodorizer cartridge?
Will an elongated soft-close seat fit my TOTO bowl?
The Bottom Line
For most people chasing a running, hissing TOTO, the TOTO Adjustable Replacement Fill Valve is the one to buy — it’s a genuine TOTO part, it comes with every washer and clamp you need in the box, and it suits any TOTO tank. If your tank is unusually deep, the Korky 528GT gives you that 8-1/2 to 14 inch reach and a 5 year warranty behind it. And if the whole tank feels tired, the TOTO Combo Kit replaces the flapper and the valve together, so you’re not reopening the lid a month later. Start with the model number inside your tank, match the inlet size, and the right part is on this list.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.





