8 Best Rear Wheel Hub | Five Lugs, Two Packs, One Silent Axle

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

Your rear-end grind ends with one check: does the part number match your car? A hub (the metal unit that carries the wheel and the bearing inside it) is not universal. Get the fitment code right and the swap is a bolt-on afternoon job. Get it wrong and you are shipping a heavy box back. The picks below are grouped by vehicle and by how they hold up, so you can match your Subaru, Ford, or Nissan in one scan.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

A rear hub usually announces itself with a drone that rises with road speed and a wheel that rocks top-to-bottom when you shake it. Below you will find eight picks matched to specific vehicles, with the part numbers and real owner patterns that decide the buy. Choosing the right rear wheel hub starts with that fitment code, then the bearing quality behind it.

Top Picks

Rear Wheel Bearing for Crosstrek 16-20, Forester 14-18, W/ABS 5-Lug, 2 Pack
Best OverallRear Wheel Bearing 2 Pack4.5+★900+ ratingsTwo hubs in one box for the Subaru crowd that needs both rear corners fixed together.Check price on Amazon
KAX 512536 Rear Wheel Bearing hub Assembly fit for Subaru Outback 2015-2021
Best for Newer OutbackKAX 512536 Rear Wheel Bearing4.5+★400+ ratingsThe single-hub answer for the newer Outback crowd, sealed four ways against grit and water. If your Subaru is a 2015 to 2021 Outback or Legacy, a 2019 to 2021 Ascent, a 2019 Forester, or a 2015 to 2019 WRX, this is your number.Check price on Amazon
DJB 512518 Rear Wheel Bearing Hub Assembly for Subaru Forester 2014-2018
Smart Two-PackDJB 512518 Rear Wheel Bearing4.5+★250+ ratingsA pre-greased two-pack that fits a wide stretch of Forester, Impreza, and Crosstrek years.Check price on Amazon

How To Choose The Best Rear Wheel Hub

The wrong hub does not fit, and a close-enough hub can hide a mismatch until the ABS light comes on. The safe process is mechanical: read your year, model, and trim, find the reference number stamped on the old part, then confirm the new hub lists that same number before you buy.

Match the reference number, not the brand

Every hub carries a reference part number — 512518, 512536, 512401, 512490, and 512388 all appear in this list. That number is the shortcut to a correct fit. A 512518 hub serves a specific set of Subaru models, while a 512401 serves a different run of years and trims. Almost every fitment failure is someone buying by car make alone and ignoring the exact code.

Count your lugs and check the ABS provision

The five-lug pattern dominates the Subaru hubs here, while the Ford Fiesta fitment runs a four-lug setup. Count the studs (the threaded bolts your lug nuts screw onto) on your old hub and match the quantity. If your car has anti-lock brakes, confirm the hub either includes the speed sensor or a tone ring (the toothed ring the sensor reads). Some hubs here include it, one notes no sensor is included, and that difference matters on a car with ABS.

Ball bearing versus roller bearing

Most hubs here use ball bearings, where metal balls roll in a track inside the hub. One pick uses a roller bearing, where cylindrical rollers carry the load. Both are pre-greased in these listings, and both need a clean sealed install. The practical rule: replace both rear hubs together, since a bearing that has been on the same axle with a failing partner usually has the same wear inside it.

Buying the two-pack

Most entries here come as a pair, and that is not a marketing trick. Rear hubs wear together, so a two-pack lets you do both sides in one garage session. The single-pack options make sense when only one side has failed and the other is young. Check the pack count on the listing before you click, because one of these fits as a single unit and another ships two.

Side-by-Side Comparison

Model Best For Reference Number Lugs Quantity Amazon
BDELI Crosstrek / Forester / Impreza Hub★ Best Overall Subaru all-rounder value 512518 5-Lug, ABS 2 Pack Amazon
KAX 512536 Hub AssemblyBest for Newer Outback Newer Outback and Ascent 512536 5-Lug 1 Pack Amazon
DJB 512518 Hub AssemblySmart Two-Pack Forester and Crosstrek pair 512518 5-Lug, ABS 2 Pack Amazon
Aspligo 512401 Hub Assembly Older Outback and Legacy 512401 5-Lug 2 Pack Amazon
ECCPP 512490 Hub Assembly Ford Fiesta rear axle 512490 4-Lug, ABS 2 Pack Amazon
Nilight 512388 Hub Assembly Nissan Altima and Maxima 512388 5-Lug 2 Pack Amazon
A-Premium Rear Bearing and Hub Subaru fitment precision 512518 5-Lug 2 Pack Amazon
Subaru Genuine 28473FL040 Hub Dealer-spec authenticity 28473FL040 5-Lug 1 Pack Amazon

Detailed Reviews

★ Best Overall

1. Rear Wheel Bearing 2 Pack

Our pick — 4.5+★ from 900+ verified ratings; the strongest balance of quality and price.

Two-Pack512518 Fitment

Two hubs in one box for the Subaru crowd that needs both rear corners fixed together.

This is the pair to reach for if your garage holds a Crosstrek from 2016 to 2020, an Impreza from 2012 to 2019, a Forester from 2014 to 2018, or an XV Crosstrek from 2013 to 2015. It ships as two complete hub and bearing assemblies under reference 512518, so both rear wheels get the same fresh part. The lugs are the five-stud pattern with ABS provisioning, which is what most of these cars roll off the lot with. It is the highest-rated hub here at 4.5+ stars across 900+ ratings, and the one I would hand most Subaru owners first.

Build quality is the thing that wins people over, and it is not luck. The maker runs ISO 9001 and IATF 16949 certified factories (the international quality-management standards for automotive parts), and the hubs are inspected on professional test equipment from DV Canada before shipping. What that means in your driveway: the bearing race and seal arrive clean, and the unit drops into the knuckle without you fighting a rough casting. That said, quality counts for the money here too — more Subaru owners flag the value than any other single point, because doing both corners yourself beats paying a shop for the same job.

Where it can bite: the noise story splits. Some of these arrive quiet and stay quiet, while a slice of buyers report a grinding hum that shows up down the road, and durability gets the most negative flags of any point in this product’s reviews. The honest read is that a ball bearing hub at this tier is a wear part, not a lifetime fit. If you are chasing a hundred thousand quiet miles, the Genuine Subaru unit further down is built for that expectation. For a daily driver doing normal commuting, this pair gets you back on the road with both rears matching.

Where it earns its keep

  • Two complete 512518 hubs in one purchase, so both rear corners get done in a single session
  • ISO 9001 and IATF 16949 certified manufacturing, with DV Canada test equipment behind it
  • Pre-lubricated and sealed, so no bearing-clearance adjustment is needed at install
  • Covers a wide Subaru spread: Crosstrek, Impreza, Forester, and XV Crosstrek

Where it asks for care

  • Noise results are split — some units hum or grind over time
  • Durability draws the most criticism of any point in this product’s reviews
  • Confirm your trim against the 512518 list before ordering; base and sport trims differ on some years

Reach for this if: you own one of the listed Subaru models and want both rear hubs replaced in one go with certified manufacturing behind them.

Think twice if: you plan to keep the car well past a hundred thousand miles and want the dealer-grade bearing inside — the Genuine Subaru pick is the one for that job.

Best for Newer Outback

2. KAX 512536 Rear Wheel Bearing

Quad Lip Seal2-Year Warranty

The single-hub answer for the newer Outback crowd, sealed four ways against grit and water.

If your Subaru is a 2015 to 2021 Outback or Legacy, a 2019 to 2021 Ascent, a 2019 Forester, or a 2015 to 2019 WRX, this is your number. The 512536 reference covers those years, and the listing names the interchange codes — HA590581, HA590603, 28473VA000 and several more — so you can cross-check the stamp on your old part. It fits as a single hub, unlike the two-pack options above, which suits you when one rear corner has failed and the other is still young.

What keeps grit out of this KAX hub is the sealing. It uses a quad lip seal (four sealing lips stacked at the bearing edge, each one a barrier against water and road grit), built from 55# steel with GCr15 steel (a hard bearing-grade steel) on the bearing surfaces. In plain terms: the grit that eats a rear bearing gets four chances to be stopped before it reaches the race. The maker backs it with a 2-year warranty and 24-hour support. Owners are consistently happy with the quality and the value here, and the noise fix is real — the hub cures the whine and vibration the old bearing was causing. That four-lip seal also keeps grease in and grit out, which is what protects bearing life on a daily-driven Outback.

The catch is durability, and it is honest. A share of owners mention the bearing did not last the distance they expected, and that is the one point that drags this pick down from a clean score. It is a fit-note, not a rescue: the 512536 is a solid daily-driver hub at a fair mid-range tier, and the warranty gives you a path if it fails early. Buy it for a commuter Outback, not for a car you plan to tow with or flog over rough ground every weekend. And at a single unit, you will want to buy a second if both rears are tired.

Pick this one if: your Outback, Legacy, Ascent, or WRX runs the 512536 reference and you are fixing one rear corner with a sealed, warrantied hub.

Look elsewhere if: both rear hubs are shot, since this ships as a single unit — the two-packs will save you a second order.

Smart Two-Pack

3. DJB 512518 Rear Wheel Bearing

5-Lug with ABSTwo-Pack Kit

A pre-greased two-pack that fits a wide stretch of Forester, Impreza, and Crosstrek years.

Start with the measurement that matters when a box lands on your porch: this kit arrives at 13.3 x 6.6 x 5.9 inches and 16 pounds, against the single KAX hub at 7.72 x 7.6 x 7.13 inches. The DJB is the longer, flatter box because it holds two complete hub assemblies, and the KAX box is the compact cube of one. That is the real difference a buyer feels — two parts, one delivery, and a garage session that covers both rear wheels.

The fit is the strongest story here. DJB lists compatibility with Forester 2014-2018, Impreza 2012-2014 (Base, Sport Limited, or Sport Premium only), Impreza 2015-2021, Crosstrek 2016-2018, Crosstrek 2019-2021 (Base, Limited, or Premium only), and XV Crosstrek 2013-2015. The hub is a five-lug with ABS, flange offset 66.5mm, flange diameter 123.9mm, and a bolt circle of 3.9 inches — numbers worth saying out loud only if your car’s parts sheet asks for them. What wins people over is fit, right after quality: this is a hub that goes on without clearance drama. It ships pre-lubricated and sealed, so you do not open the box until it is time to bolt up, and no bearing adjustment is needed.

The honest snag is durability, and the reports split. Some owners get a long run from the bearing, others see one fail inside a month. That is the nature of a mid-tier steel hub, and B19037 is the model code if you want to cross-reference. Our read: a good buy if your Forester or Crosstrek is a normal daily and you want both sides done. If you need the last word in long-term bearing life, pay up for the factory part.

What you get in the box: two 512518 hub and bearing assemblies, pre-greased and sealed, made from alloy steel to ISO 9001 and IATF 16949 standards. The two-pack format is the reason to buy here — you fix the pair, not just the noisy corner.

The honest limit: durability is mixed in the reports, with some units going early. Cross-check your exact trim against DJB’s compatibility list before you order, since base and sport trims differ on the Impreza and Crosstrek years.

Confident call: for a Forester or Crosstrek owner doing both rear hubs at once, this pair delivers fit, sealing, and certified steel in one box.

The caution: mixed durability reports mean you should inspect the bearing surfaces on arrival and keep your install receipts.

Older Subaru Workhorse

4. 512401 Rear Wheel Bearing

Forged Metal StructureRear Position

The heavier pair built for the older Subaru generation, with a forging process behind the steel.

At 17.2 pounds, this two-pack is the heaviest box in the lineup, and there is a reason. Aspligo forges the hub structure to improve the metal’s strength and toughness, then upgrades the seal to hold lubrication and shed heat and rust. Compared with the 16-pound DJB pair above, you are looking at a piece that carries more mass into the load path — a small difference in shipping weight, a real one under a loaded car. The 512401 reference covers Outback 2010-2014, Forester 2009-2013, Legacy 2010-2014, Impreza 2008-2014, Crosstrek 2019-2021, WRX 2013, BRZ 2013-2019, WRX STI 2013-2014, Scion FR-S 2013-2016, Toyota 86 2017-2020, and GR86 2022-2023.

This is a fit-first hub. The flange diameter is 4.88 inches, the bolt circle 3.94 inches, and the pattern is five lug on rear position. It has no ABS sensor included, which matters — the listing calls that out plainly, so confirm whether your car reads the ABS from the bearing tone ring or from a separate sensor before you buy. Customers note it fits well and goes on without fuss. The install notes are strict for a reason: never open the bearing packaging early, never disassemble the hub, and never install a magnetically coded ring backwards.

The honest split is quality and value. Some owners rate the steel and the finish high for the tier, others call it poor value after a short service life. That mirrors the heavier hub’s simple promise: a forged, sealed replacement at an entry-level position. It is not the part to pick if you want a known long-runner. It is the part to pick if you are restoring a 2010-2014 Outback or Legacy and want both rear corners done without chasing the dealer counter.

The case for it

  • Forged hub structure for strength and toughness under load
  • Upgraded seal for lubrication retention, heat dissipation, and rust resistance
  • Two-pack covers both rear corners in one order
  • Wide cross-compatibility: Outback, Forester, Legacy, Impreza, BRZ, and Toyota 86 family

The catch to know

  • ABS sensor is not included — verify how your car reads its wheel speed
  • Quality and value reports are mixed on service life
  • At 17.2 pounds for the pair, it is a heavy box to handle and return

Best for: older Subaru and Toyota 86-platform owners who need both rear hubs and value a forged, sealed build.

Worth noting: no ABS sensor in the box, so a car that relies on a separate sensor needs the right part in the right place.

Fiesta Fitment

5. ECCPP 512490 Wheel Hub Bearing

4-Lug with Tone RingTwo-Pack

The four-lug pair for the Ford Fiesta, including the ABS tone ring the others do without.

If your driveway holds a Ford Fiesta from 2011 to 2019 in any trim except the ST, this is the hub your car is asking for. The 512490 reference, four-lug pattern, and left-and-right rear fit are all spelled out in the listing, and the pair ships as two units. The tone ring sensor is included on this one — the toothed ring that feeds your anti-lock brakes — which separates it from the Subaru-fit hubs that leave the sensor out. For a Fiesta owner who has seen an ABS light alongside the rear drone, that inclusion is the deciding detail.

The seal design is where ECCPP makes its case. It builds the hub with an anti-pollution seal (a barrier that keeps grit out of the bearing), and the wheel bolts carry a protective coating against rust. In a northern winter, that coating is the difference between a lug nut that turns free and one that has to be cut off. Owners find the install straightforward and the noise gone after the swap, and the work itself is the reason most buy — at a mid-range tier it sits well below the dealer counter.

Where it gives you pause is durability. A number of reviewers point out a bearing failing within six months, and that is the one honest knock against this pick. It is a fit-note: the 512490 is a solid daily-driver replacement at its tier, not a part built for a car that sees heavy loads or long towing duty. Keep the install clean, do both sides since the pair is included, and treat the service life as a wear-part window rather than a permanent fix.

Go with this: Ford Fiesta owners (non-ST, 2011-2019) who want both rear hubs plus a tone ring sensor in one purchase.

Size up instead if: you need a bearing you can trust for the long haul — the repeated short-life reports make this a daily-driver part, not a heavy-duty one.

Nissan Value Pick

6. Nilight Rear Wheel Hub Bearing

Roller Bearing5-Lug Pair

A roller-bearing hub for the Altima and Maxima, priced for the value-conscious Nissan owner.

The 512388 reference here covers 2007 Altimas with four-wheel ABS, 2008-2018 Altimas, 2009-2019 Maximas, 2015-2016 Muranos, 2013-2019 Pathfinders, and a handful of Infiniti models including the 2013 JX35 and 2014-2019 QX60 — all FWD only. The hub is a five-lug with a four-hole flange and no speed sensor included. Pre-greased and ready to bolt up, it is the pick for a Nissan owner whose rear whine has turned into a howl.

What separates this hub from the ball-bearing picks above is the bearing type. Nilight uses a roller bearing, where cylindrical rollers carry the load instead of balls. The maker builds it from alloy steel and tests it in the field, and the result is a hub that reads as steady under a fully loaded Altima. Value is where owners give it the most credit — the biggest chunk of the feedback here lands on the price-to-part ratio, and functionality comes a close second. The stud pattern is worth a hard check, though: one portion of the reports flags the lug studs as not matching the car, so confirm your wheel stud quantity and thread pitch before you order.

The blunt part: durability is the weak note. A set of owners reports the hub coming apart after very short use, and fit complaints live alongside that. It is still a genuine value pick for a teenager’s first car or a workhorse Altima — cheap enough to justify the gamble — but a car doing serious mileage or towing deserves the Genuine Subaru-tier attention to bearing life. The pair covers both rear corners, and the roller bearing (a bearing that spreads load across many rollers) is a real difference in how the hub carries load.

Why Nissan owners pick it

  • Roller bearing construction for load carrying, distinct from the ball-bearing hubs here
  • Broad Nissan and Infiniti coverage: Altima, Maxima, Murano, Pathfinder, JX35, QX60
  • Value is the most-praised point in the feedback — a fair price for the part
  • Pre-greased and pre-assembled for a bolt-on install

What to watch

  • Fit complaints include lug studs that do not match some cars
  • Durability is the recurring negative — some hubs fail early
  • No speed sensor included, so confirm your ABS setup

Match it to: an Altima, Maxima, Murano, or Pathfinder owner who wants a roller-bearing pair at a wallet-friendly tier.

Test the studs first: verify your lug nut thread and count, since fit is the single most-flagged issue on this one.

Premium Fitment Pick

7. A-Premium 2 x Rear Wheel Bearing and Hub Assembly with 5-Lug

GCr15 Steel1-Year Guarantee

The precision-first pair, built on GCr15 steel and sold with a one-year guarantee.

Fit is the headline with the A-Premium pair, and the feedback says so consistently. It is built to the 512518 reference and covers Forester 2014-2018, Impreza 2012-2014 (Base or Sport Limited or Sport Premium only), Impreza 2015-2021, Crosstrek 2016-2018, Crosstrek 2019-2021 (Base or Limited or Premium only), and XV Crosstrek 2013-2015. The material is GCr15 steel paired with 65Mn steel — two high-carbon grades used where surface hardness and wear resistance matter. The studs are steel and spec’d to match the original, so the rotor, wheel, and lug nuts all line up without shimming.

The difference you feel with the A-Premium hub is quiet. Owners describe it as quiet after install, with one noting it works flawlessly with the ABS sensors (the wheel-speed sensors your anti-lock brakes read), and the noisy old bearing gives way to a clean ride. It ships pre-greased with the CV spline insert style (the splined collar that mates the hub to the axle) noted in the specs. The 1-year unlimited-mileage guarantee is a real safety net here, and it is not matched by every pick in this lineup. Our read: this is the fitment-first choice for a Subaru owner who wants the job done once and done right, and the sealing components — new bearing cage, spline, and seals — are exactly the wear items that fail on a tired hub.

The one wrinkle is service life, and the reports are honest about it. Most buyers are confident in the durability, but a subset report a hub that does not last a full year. That keeps this a premium-tier pick with a caveat rather than a certainty. For a daily-driver Subaru, the guarantee and the GCr15 steel give you a better case than the budget entries. For a car that lives on rough roads or carries a trailer, no hub in this list is a lifetime part — and A-Premium’s warranty at least gives you a return path.

The precision case: 512518 reference fit, GCr15 and 65Mn steel, pre-greased and splined for direct CV axle insertion, with a 1-year unlimited-mileage guarantee on top.

The real-world check: durability reports are mixed, with a few hubs not lasting a year. The guarantee softens that risk, but a heavy-use car should still expect a wear-part replacement window rather than a permanent fix.

Confident pick for: Subaru owners who rate fit and quiet operation above all else and want a guarantee behind the part.

Think past it if: your car does heavy towing or rough-road miles — the mixed durability reports mean a daily-driver window, not a lifetime promise.

Genuine Factory Part

8. Subaru 28473FL040 Rear Axle Hub

Genuine SubaruSingle Hub

The factory part, straight from the dealer supply chain, for the owner who trusts the original.

Some buyers do not want a substitute at any tier, and this is the hub for them. It is the Genuine Subaru unit under part 28473FL040, with the prior numbers 28473FJ020 and 28473FJ000 noted for cross-reference. Fitment runs 2013-2019 Crosstrek, 2014-2018 Forester, and 2012-2019 Impreza (non-turbo). Everything else on this page is an aftermarket interpretation of that part; this is the original. For a car still under warranty or a driver who wants the factory stamp on the box, that is a legitimate reason to pay more.

Authenticity and fit are the twin strengths, and they come in a single hub. Shoppers say it drops straight onto the car without fuss and runs quietly after the swap — one sums it up as running like new once installed. It comes as one complete hub unit, not a two-pack, so plan on ordering a second if both rear corners are tired. The material is alloy steel and the unit meets OEM specification. There is also a listed 5-year EU spare-part availability window, which tells you Subaru expects to support the part for a long run.

The honest trade-off is value-per-corner. At a single unit in the premium tier, it costs more for one hub than several of the two-packs here cost for both. Whether that is worth it depends on how long you plan to keep the car: for a Subaru you will drive into the ground, the factory part and its support window make financial sense. For a car you might sell in two years, a mid-tier pair saves money on the same job. That is the whole argument, stated fairly.

What you are paying for: the genuine Subaru 28473FL040 hub, alloy steel, OEM specification, with a listed 5-year EU spare-part availability window. It is the part the car was built with.

The check before you buy: it ships as one unit. If both rear corners need replacing, order two, since the box does not cover a pair the way most picks here do.

Right for the long-hold owner: a genuine Subaru hub is the choice when the car is a keeper and you want the original part and its support window.

The trade you accept: one hub at a premium tier can outweigh a two-pack — buy one or two, matched to how many corners are actually worn.

Know the Specs

Reference Part Number

The reference number — 512518, 512536, 512401, 512490, or 512388 — is the single most reliable shortcut to a correct fit. It is the industry code that tells you which vehicles a hub was engineered for, and it is stamped on your old part. Match that code, plus your trim level, and the hub will bolt up. Ignore it, or shop by car make alone, and a 512518 hub ordered for a car that needs a 512401 will not work. Always confirm the reference against the listing’s fitment list before you buy.

Bearing Type: Ball vs Roller

A ball bearing rolls on metal spheres inside the hub, while a roller bearing rolls on cylinders. Both carry the wheel’s load and both are pre-greased in these listings. Rollers spread load over a longer contact line than balls, which is why one Nissan-fit pick uses them. Neither is automatically better for every car; the original part’s design is what your suspension was tuned around. Replace in pairs where you can, and keep the install clean — grit in the bearing is what starts the grinding noise in the first place.

Common Questions

How do I find the right rear wheel hub for my car?
Read the reference number stamped on your old hub, then match it against the listing’s fitment list and reference numbers. A 512518 hub fits a specific run of Subaru models, while 512490 fits the Ford Fiesta and 512388 fits the Nissan Altima and Maxima. Confirm your year, model, and trim, because base and sport trims differ on some Impreza and Crosstrek years. Never order by make alone.
Will a rear hub for a Subaru Outback fit my Legacy?
Only if the reference number and fitment list say so. The 512536 hub is listed for Outback 2015-2021 and Legacy 2015-2021, so it covers both. But the 512401 hub is listed for Outback 2010-2014 and Legacy 2010-2014, which is a different generation. Always check the exact years in the listing; a hub for one generation of Legacy will not bolt onto another.
Do I need to replace both rear hubs at the same time?
It is the recommended practice when both bearings show the same age and wear, since a bearing that has run alongside a failing partner usually has similar wear inside. Most picks here ship as two-packs for that reason. If only one side has failed and the other is young, a single hub like the KAX 512536 or the Genuine Subaru 28473FL040 is the pragmatic choice.
Why does my rear hub make a grinding noise?
A grinding noise from the rear usually points to a worn bearing race inside the hub, or grit that has got past the seal and damaged the bearing. Replacing the hub assembly is the standard fix, since the bearing is sealed inside it. Several picks here address the noise directly, and the noise level draws praise on the A-Premium pair and the KAX hub. If the noise arrives with an ABS light, suspect the tone ring or sensor too.
What is an ABS tone ring and do I need one?
An ABS tone ring is the toothed ring the anti-lock brake sensor reads to detect wheel speed. If your car has ABS, the hub either includes the tone ring or a speed sensor, or it relies on a separate sensor elsewhere. Some hubs here include it — the ECCPP 512490 for the Ford Fiesta is listed with an ABS tone ring sensor — while others state that no sensor is included, such as the Aspligo 512401 and the Nilight 512388. Confirm how your car reads wheel speed before buying.
Can I install a rear wheel hub myself?
Yes, with the right tools and a clean approach. These hubs arrive pre-lubricated and sealed, so no bearing clearance adjustment is needed. Do not open the bearing packaging before install, do not disassemble the hub, and do not install a magnetically coded ring backwards. The install is essentially unbolting the old assembly and bolting up the new one, though a seized bolt or rusted knuckle can add time.
Is a genuine Subaru hub better than an aftermarket one?
The genuine Subaru 28473FL040 is the factory part and carries a listed 5-year EU spare-part availability window, which is a strong case for a car you plan to keep. Aftermarket hubs like the A-Premium pair use certified steel and some include a guarantee, which is strong value. Neither automatically wins. The factory part suits a keeper, and a certified aftermarket pair suits a driver who wants both corners done for less.
How many lugs does my rear hub have?
Count the threaded studs on your existing hub. Most Subaru-fit hubs here are five-lug, and the Nissan Altima pick is five-lug as well. The Ford Fiesta pick is four-lug, so a five-lug hub will not work on it. Matching lug count is as important as matching the reference number, and some reports of poor fit trace back to a stud mismatch, particularly on the Nilight 512388.
Do these rear hubs come pre-greased?
Most of the listings state that the hub arrives pre-greased and sealed, including the DJB 512518 pair and the A-Premium pair. Do not add grease or open the seal before installation; the bearing is packed and sealed at the factory for a reason. Opening it early lets dirt in, which is exactly what shortens bearing life. If a listing does not say pre-greased, check the product page before ordering.
What does the warranty cover on these hubs?
It varies by brand. The KAX 512536 carries a stated 2-year warranty, the A-Premium pair has a 1-year unlimited-mileage guarantee, and the ECCPP 512490 lists a 1-year warranty. Others in this list do not publish a warranty figure in their listing details. Check the warranty line on the product page for the pick you choose, and keep your purchase record so a claim is simple if the bearing fails early.

The Bottom Line

For most Subaru owners, the rear wheel hub winner is the BDELI 512518 two-pack because it covers both rear corners in one box with certified manufacturing behind it, and it earns the top spot on 4.5+ stars across 900+ ratings. If you need fitment precision and a guarantee, the A-Premium pair leads on quiet operation and GCr15 steel. And if your car is a keeper and you want the factory part, the Genuine Subaru 28473FL040 is the one to reach for. Check your reference number first, then pick your tier — the right code on the right hub is what actually ends the rear-end grind.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top