Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your oil burner has gone quiet, the pump is usually the part that failed — and you want one that bolts straight on, primes without a fight, and holds pressure through a cold winter. The short answer: the Beckett 2184404u A2EA-6527 is the pick for most homes, because it is the OEM (original equipment manufacturer) part that many oil furnaces were built around, and it carries the highest owner satisfaction of the group at 4.5+ stars across 250+ ratings. Below, every pick is matched to a specific burner setup, so you spend once instead of twice.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
A fuel pump is a small part with a big job: it pulls heating oil from the tank and pushes it to the nozzle at the right pressure. Get the gallons-per-hour rating and the pressure range wrong and the burner soots, stalls, or refuses to light at all. That is why this breakdown leads with the numbers that actually decide compatibility, and why the final pick for a waste-oil shop heater is separated from the standard No. 2 fuel pumps. Read on for the oil furnace pump that matches your burner instead of guessing at the counter.
Top Picks

How To Choose The Best Oil Furnace Pump
An oil furnace pump is not a universal part, and that is the trap most buyers fall into. Two pumps can look nearly identical on the shelf and still refuse to feed your burner, because the pump is matched to the nozzle, the firing rate, and the direction the motor spins. Get those three right and installation is a short job. Get one wrong and you are bleeding the line again by flashlight.
Match the GPH rating to your nozzle first
GPH stands for gallons per hour — the volume of heating oil the pump pushes to the nozzle. A pump rated at 3 GPH at 100 PSI is built to feed a burner set up for that flow. If your furnace’s data plate calls for a smaller or larger nozzle, a 3 GPH pump will either over-fire or starve it. Check the plate on the burner before you order anything.
Understand the pressure range in PSI
PSI is pounds per square inch, the pressure the pump delivers so the oil atomizes into a fine spray at the nozzle. Some pumps hold one pressure band — the Suntec A2VA-7116 runs 3 GPH at 100 PSI. Others cover a wider band, like the A2VA-7116 replacement that handles 3 GPH at 100-150 PSI and 2 GPH at 150-200 PSI on No. 2 and lighter fuel. A wider band gives a technician more room to dial in the burner.
Single stage versus two stage
A single-stage pump pulls oil on one line and is the common setup for a standard tank above the burner. A two-stage pump can lift oil harder and handles a two-pipe layout better. All four picks here are single-stage units, so confirm your piping matches before ordering. If your system runs a return line, that is the moment to check with your technician rather than assume.
Rotation direction is not a detail
Rotation means which way the pump’s shaft is driven to move fuel. The A2VA-7116 is a right-hand (RH) rotation pump, and a motor spinning the wrong way will not feed oil no matter how clean the install is. Confirm the rotation your burner needs against the pump listing before you buy.
Side-by-Side Comparison
| Model | Best For | Flow / Pressure | Stage | Fuel Type | Amazon |
|---|---|---|---|---|---|
| Beckett 2184404u A2EA-6527 Cleancut★ Best Overall | Standard oil furnace, OEM replacement | — | — | Heating oil | Amazon |
| 100 PSI at 3 GPH A2VA-7116 | Straight swap on a 3 GPH burner | 3 GPH at 100 PSI | Single | No. 2 and No. 1 fuel oil | Amazon |
| Suntec A2VA-7116 HVAC Part | Cross-reference replacement for older pumps | 3 GPH at 100-150 PSI; 2 GPH at 150-200 PSI | Single | No. 2 and lighter fuel | Amazon |
| Suntec A2RA-7710 Reznor Clean Burn | Waste-oil shop heater rebuild | — | — | Waste oil | Amazon |
Detailed Reviews
1. Beckett 2184404u A2EA-6527 Cleancut Oil Pump 3450
Our pick — 4.5+★ from 250+ verified ratings; the strongest balance of quality and price.
The OEM part that skips the guessing game and just feeds the burner.
The reason this one sits on top is simple: it is the genuine Beckett part, made in the USA, and it is the pump a large share of oil furnaces were originally built around. That matters because an OEM part means the mounting pattern, shaft, and pressure behavior already match the burner you own. You are not adapting anything, and you are not bleeding the line twice hoping it catches. At 4.5+ stars across 250+ ratings, it carries the highest owner satisfaction in this group.
What wins people over is how it behaves after a cold start. The Cleancut design is built to cut down dry start-up, so the pump primes and pushes oil to the nozzle instead of whining on air. Buyers report it runs cleaner and loads the motor less than the pump it replaces. Leak-through protection is part of the design too, which is the quiet detail that keeps oil where it belongs instead of weeping onto the floor.
The electrical side is forgiving, which helps on older installs. It takes 24, 110-120, or 200-240 VAC at 50/60 Hz (50 Hz not UL approved), plus 12 VDC, so it will run off the control voltage your burner already supplies. Ambient temperature tops out at 115 degrees Fahrenheit, which covers a normal basement or utility room. And the fit-and-install side is where the complaints never show up: owners mention it dropping in cleanly and going to work like the part it replaced. The one thing worth saying plainly is that this is a pump only — no nozzle, no couplings, no gaskets — so plan the small bits before you start the job.
What Earns The Top Spot
- Genuine OEM Beckett part, made in the USA, so the mount and shaft match the burner
- Cleancut design targets dry start-up — the pump primes instead of starving on air
- Runs on 24, 110-120, or 200-240 VAC plus 12 VDC, so it suits most control setups
- Leak-through protection and a lighter motor load than the pump it replaces
Where It Needs A Plan
- Sold as the pump only — you supply the nozzle and fittings
- Not a waste-oil component; it is built for standard heating oil
At 4.5+ stars across 250+ ratings, it is the safest match for a standard No. 2 oil furnace.
Straight swap for most homes: pick this if your burner runs standard heating oil and you want the factory-correct part without measuring anything.
Wrong tool for waste oil: a shop heater burning used oil needs a different body entirely — look at the Reznor-spec pump below.
2. 100 PSI at 3 GPH A2VA-7116 Single Stage Oil Fuel Pump
A 3 GPH straight swap that owners describe as drop-in and done.
If your burner plate reads 3 GPH and 100 PSI, this is the pump with no translation needed. It is a single-stage Suntec unit spinning at 3450 RPM, rated for 3 GPH at 100 PSI, with right-hand rotation and threaded NPT connections. It is built for No. 2 and No. 1 fuel oil, which is exactly what a home heating furnace burns. Owners rank reliability right behind build quality.
Owners describe it as a drop-in replacement that just works, with quality and reliability leading the reviews. The NPT threaded inlets are standard pipe threads, so your existing fittings seat the way they should. For a straight replacement of a tired 3 GPH pump, this is about as low-risk as the category gets. One honest note about the listing: it is a very compact unit at 1 x 1 x 1 inches of listed dimensions, so confirm the part number against your old pump rather than sizing it by eye.
The single-stage build is the main thing to weigh. It is designed for a one-line feed, and if your system runs a return line you want a two-stage unit instead. On a standard tank-above-burner single-line layout, though, it is the right match.
Owner verdict, in short: the pattern across the listings is a replacement part that fits, installs, and holds up — with reliability treated as the reason to buy it again.
Fit check before you click: 3 GPH at 100 PSI, right-hand rotation, single stage. All three need to match your burner.
Fits your data plate: reaches for this if you are swapping a 3 GPH pump on a single-line No. 2 oil setup.
Look elsewhere if: your burner runs a return line that calls for a two-stage pump.
3. Suntec A2VA-7116 Oil Burner Pump
The cross-reference champ when your old pump’s part number is long since discontinued.
Here is the scenario this pump solves. You have an older burner, the original pump is stamped with a number nobody stocks anymore, and you need something that drops in without rebuilding the fuel train. The A2VA-7116 replacement covers a spread of retired part numbers — 2460GU, Sid Harvey P4-91R and P4-91, Wayne Combustion 13495, and the Suntec A2VA-7016 and A2VA7016. That cross-reference list is the reason it earns a spot; it is a compatibility play, not a spec play.
As for the working numbers, it is a single-stage pump at 3450 RPM that delivers 3 GPH at 100-150 PSI on No. 2 and lighter fuel. It also runs 2 GPH at 150-200 PSI on No. 2 fuel, so a technician has a wider pressure window to work with than a fixed-band pump gives. The body is metal and the unit weighs 3.45 pounds in listed weight — a solid part, not a plastic shell.
Now the honest part. This pump has a thinner review history than the two picks above — a handful of ratings at 4.0+ stars — so you are leaning more on the spec match than on a deep pile of owner experience. That is not a knock on the part; it is exactly the pump a burner tech reaches for when replacing a discontinued unit. Just verify the cross-reference against your old pump’s stamp before you order. The metal body and the wide pressure band make it the most adaptable of the standard-fuel pumps here.
Why it’s worth considering: the replacement list is broad and the 100-150 PSI band on 3 GPH leaves room for a technician to tune the nozzle.
The trade-off to know: the review history is thinner than the leaders, so confirm the part number match yourself.
Best for the discontinued-pump hunt: hand your old pump’s part number to this one and confirm the match before ordering.
Not the first call if: you already have a clean 3 GPH burner and a same-model old pump to swap — the simpler picks above save you the cross-referencing.
4. Suntec A2RA-7710 Waste Oil Heater Pump
Built for the shop heater burning used oil, not the furnace in your basement.
A waste-oil heater in a garage or shop runs a different fuel and a different pump body than a home furnace, and this is that pump. The 1-year warranty is the headline you rarely get on a heating-oil component, and it is the piece of mind a small shop owner needs when the heater is the one thing keeping the bay warm. It is a Suntec A2RA-7710 built to the Reznor and Clean Burn 107032 spec, so it is a direct fit for those waste-oil heater models rather than a universal part you hope will work.
The body itself is a compact unit at 5.2 x 5 x 4.92 inches. That footprint is the physical reality of a waste-oil pump — it is a sturdier casting than the tiny 1 x 1 x 1-inch standard fuel pumps, built to push thicker used oil rather than clean No. 2. If you have ever matched a standard furnace pump to a waste-oil burner and watched it struggle, that size difference tells you why: different fuel, different duty.
There is not much review history to go on here — a handful of ratings at 4.5+ stars — so the case rests on the spec match and the warranty. Confirm the 107032 or A2RA-7710 number against your heater’s original pump before ordering. If the number lines up, this is the right part and the warranty backs it. If your heater is a standard home furnace, though, this is not the pump you want.
Where the value is: a 1-year warranty on a waste-oil pump body is the real draw, plus a direct Reznor and Clean Burn spec fit.
The caveat to size up: thin review history means your own part-number check is the safety net.
For the shop heater: buy this if your Reznor or Clean Burn waste-oil heater needs its 107032 or A2RA-7710 pump replaced.
Skip for the home furnace: a standard No. 2 oil furnace takes the standard-fuel pumps above, not this waste-oil body.
Know the Specs
GPH and PSI — the two numbers that decide fit
GPH is the flow, in gallons per hour, and PSI is the pressure that flow arrives at. Together they define what the pump feeds a nozzle. A 3 GPH pump at 100 PSI is matched to a burner nozzle calling for that flow and pressure. A pump covering 3 GPH at 100-150 PSI, or 2 GPH at 150-200 PSI, gives a technician a wider band to set the burner. Always match the pump to the nozzle, not the other way around.
Single stage, rotation, and fuel type
A single-stage pump pulls fuel on one line — the common layout for a standard tank. Rotation is the direction the pump’s shaft is driven, and a right-hand pump on a motor turning the wrong way will not move fuel. Fuel type matters too: No. 2 and lighter fuel oil for standard furnaces, while waste-oil heaters take a different, sturdier pump body built for thicker used oil.
Common Questions
How do I know if my oil furnace needs a single-stage or two-stage pump?
Will a 3 GPH pump work if my old pump had a different rating?
What does the PSI range on an oil pump actually control?
What does right-hand rotation mean and does it matter?
Can I use a standard furnace pump on a waste-oil shop heater?
Why does my replacement pump keep losing prime after install?
What voltage does an oil furnace pump need to run?
Does the pump come with a nozzle and fittings?
How long should an oil furnace pump last?
Can I replace the pump myself or should I call a technician?
The Bottom Line
For most homeowners, the oil furnace pump winner is the Beckett 2184404u A2EA-6527 Cleancut because it is the genuine OEM part built around a large share of oil furnaces, and it primes on cold starts instead of fighting you. If you want a straight 3 GPH swap at 100 PSI with right-hand rotation, the A2VA-7116 is the drop-in choice. For an older burner whose pump part number is discontinued, reach for the Suntec A2VA-7116 HVAC replacement and check its cross-reference list. And if your shop heater runs used oil, the Suntec A2RA-7710 Reznor Clean Burn is the one built for that job — with a 1-year warranty to back it. Match your nozzle, pressure, and rotation first, and the right pick here will keep the burner running all winter.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.


