Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
Your outside faucet is dripping, the handle spins without grip, or the vacuum breaker spits every time you hook up a hose. The fix is usually a small brass-and-rubber repair kit, not a new faucet. This guide covers only kits built to fit Woodford models, so you can match the right part to your hydrant and stop the drip in a single afternoon.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
The trick with these kits is matching the model number stamped on your faucet body to the kit’s replacement number. Here is how the kits differ in parts, weight and fit, so you can pick the right Woodford Faucet Repair Kit the first time.
Top Picks
How To Choose The Best Woodford Faucet Repair Kit
Start under the faucet, not on the shopping page. Woodford stamps a model number on the body — 17, 24, 25 or 27 — and each repair kit is cut for one family of faucets. A kit for a Model 17 sillcock will not rebuild a Model 25 freezeless hydrant, because the internal stem and plunger are different lengths.
Match the replacement number first
Look for the part number the kit replaces. RK-17MH is the common rebuild kit for Model 17 outside wall faucets. RK-25 covers the Model 25 freezeless series, and RK-24 is its own kit for the Model 24. Kits that list several replacement numbers at once, like RK-17MH 30002 30096 30059, are telling you they cross-reference older part codes — handy if your faucet was installed years ago.
Check whether the kit is the whole head or a partial fix
A complete rebuild kit includes the handle, handle screw, packing nut, packing, packing support washer, check valve and the vacuum breaker float. A partial kit may only carry the rubber seals. If your faucet has sat outside through several winters, the full head kit is the safer buy because you replace every wear part in one pass.
Look at the seals and the valve material
Rubber seals are what stop the drip. Kits with NBR rubber seals (a nitrile rubber that resists heat and stays flexible in cold) are built to keep sealing through freezing nights. More seals in the bag means fewer trips back to the store — one kit here ships with 3 NBR seals plus a check valve seal that a comparable kit leaves out.
Decide if you need the pressure relief side
Some Woodford frost-proof faucets have an adjustable rod and a pressure relief valve inside. That rod lets the valve drain water back so the body does not split when temperatures drop. If your faucet has that adjuster, the rod-and-PRV kit is a separate item from the handle-and-packing kit.
Side-by-Side Comparison
| Model | Best For | Kit Type | Item Weight | Fits | Amazon |
|---|---|---|---|---|---|
| Model 25 Repair Kit RK-25★ Best Overall | Full 8-piece rebuild | Handle, stem and packing set | 1.44 ounces | Woodford Model 25 | Amazon |
| RHWRK17 Outside Wall KitBest Value | Extra seals on a budget | 9-part handle and seal kit | — | Woodford Model 17 | Amazon |
| Woodford Mfg. RK-24Trusted Brand Part | Model 24 owners | Genuine Woodford rebuild kit | 4 ounces | Woodford Model 24 | Amazon |
| Eagle 4206546 RK-Y34 | Y34 plunger replacement | Stem, packing and plunger kit | 4.6 ounces | Woodford Y34 hydrant | Amazon |
| Woodford RK-17MH | The proven Model 17 rebuild | Full rebuild valve kit | 1.6 ounces | Woodford Model 17 | Amazon |
| RK-17MH Metal Handle Kit | Fast handle-and-seat swap | Metal handle rebuild kit | 2.4 ounces | Woodford Model 17 | Amazon |
| Woodford RK-ADJ-PRV Rod Kit | Frost-proof rod and relief valve | Adjustable rod with PRV | 9.6 ounces | Woodford Model 14 & 17 | Amazon |
| Eagle Mountain RK-17MH | Complete Model 17 kit with float | Handle, float and check kit | — | Woodford Model 17 | Amazon |
| Bzcovac RK-25 Service Kit | Model 20, 25 and 27 series | 8-part full restoration kit | 5.9 ounces | Woodford Model 20, 25, 27 | Amazon |
Detailed Reviews
1. Model 25 Repair Kit RK-25
Our pick — 4.5+★ from 250+ verified ratings; the strongest balance of quality and price.
The featherweight eight-piece kit that rebuilds a Model 25 head without swapping the whole faucet.
If you own a Woodford Model 25 freezeless faucet and the drip has started, this is the kit that fixes it at the source. It ships as an 8-piece set with a polished finish and a single-hole installation, meaning the parts slide straight into the faucet body you already have mounted on the wall. The whole kit weighs 1.44 ounces, so it arrives in a small bag you can hold between two fingers.
What makes it the top pick is the depth of the rebuild. Rather than patching one seal, the set replaces the wear parts inside the head so you are not back under the sink next season. The faucet body stays on the wall — no cutting, no re-plumbing. And it fits older faucets too; the maker’s own customers describe it working on a faucet that had been in service for 30 years.
Here is the honest catch. This is a genuine Woodford part with no manufacturer warranty listed, so the quality rests on the part itself rather than a guarantee. You also need to confirm your faucet is a Model 25 before ordering, because this kit is cut for that series and not the Model 17 sillcock. For the price of a kit versus a full faucet replacement, the value is straightforward.
What earns its place up top
- 8-piece set rebuilds the head instead of patching one seal
- 1.44 ounces — a tiny bag that ships flat and stores in a drawer
- Slides into the existing faucet body with a single-hole install
- Polished finish keeps the brass looking clean outdoors
- Proven on a 30-year-old faucet, per the maker’s customer feedback
Where it asks you to be careful
- No manufacturer warranty listed
- Cut for Model 25 — check your faucet stamp before ordering
- You supply the wrench and the patience for a tight under-sink reach
Reach for this if: you have a Model 25 freezeless faucet that drips and you want a full head rebuild in one order.
Look elsewhere if: your faucet is a Model 17 sillcock — the parts will not line up.
2. Woodford Model 17 RK-17MH Repair Kit
Nine parts in one bag, including a check valve seal the standard RK-17MH kit leaves out.
The headline here is the seal count. More rubber in the bag means more chances to stop the leak without a second trip to the store.
It is also built for the weather. The aluminum wheel handle and brass packing nut are chosen to resist rust, and the multi-part kit covers the handle screw, packing, packing support washer, valve seat rubber, retainer screw and the RK-17VB vacuum breaker float kit. One smart touch: the float is tied with a copper wire so it does not separate while you thread it in, and you simply cut the wire once the part is seated.
It is worth knowing this is a compatible part, not a genuine Woodford item, and it is cut only for the Model 17 outside wall faucet. If your faucet is a Model 25 or 24, it is the wrong bag of parts. For a Model 17 owner who wants maximum seals up front, it is the value play.
Seal-heavy by design: the extra check valve seal and three NBR seals make this the most rubber you get in a Model 17 bag, which matters most if your faucet has already been rebuilt once.
Model 17 only: the parts are dimensioned for the Model 17 sillcock, so confirm the stamp on the body before you open the bag.
Worth grabbing if: your Model 17 sillcock needs a fresh handle and every seal at once, and you want spares left over.
Think twice if: you own a Model 25 or 24 — this bag will not fit.
3. Woodford Mfg. Repair Kit RK-24 – 1 Each
The genuine American-made kit for the Model 24 faucet that most generic bags simply do not cover.
Woodford’s own RK-24 kit is the direct answer for a Model 24 faucet, and it is made in the USA. The metal handle and gold finish give it a solid, factory-style look, and the full kit weighs 4 ounces — noticeably heavier than the 1.44-ounce RK-25, because this bag carries more metal in the handle and stem.
The dimensions tell you it is a complete head kit: at 6 inches deep, 5 inches wide and 1.5 inches high, the bag measures roughly four times the footprint of the compact RHWRK17 sillcock kit at 1.5 inches by 3 inches by 4 inches. That extra space is the handle and stem sitting alongside the seals. It mounts on the wall and drops into a single hole, matching the faucet body you already have.
The trade-off is fit scope. This is a Model 24 part, plain and simple, so it will not rescue a Model 17 or Model 25 hydrant. If your faucet carries the Model 24 stamp, this is the original-equipment route.
Original-equipment answer: a genuine Woodford part made in the USA, sized at 4 ounces for a full metal handle and stem set.
One model only: built for the Model 24 — no cross-fit with the other Woodford series.
Buy it when: the stamp on your faucet reads Model 24 and you want the factory part rather than a compatible one.
Pass it over when: your faucet is a Model 17 or Model 25 — the stems do not match.
4. Eagle 4206546 Genuine Woodford Repair Kit
A brass-stem kit built around the Y34 plunger, for hydrants the sillcock kits cannot touch.
This is a different animal from the Model 17 bags. The Eagle kit carries a #3 packing nut, packing, packing support washer, a brass rod stem and the 18 Y34 plunger — the internal parts that make a Y34 hydrant shut off cleanly. The brass material and brass handle are picked for corrosion resistance outdoors, and the kit weighs 4.6 ounces.
Owners consistently report that the faucet shuts off and runs properly after the swap. The faucet shuts off and runs like it should after the swap. Fit the right stem and plunger, and the leak stops.
The thing to check is the model. This kit is built for the Y34 hydrant internals, not the Model 17 wall faucet, so it will not line up with a sillcock rebuild. For a Y34 owner, it is the specialist part you have been hunting.
Why Y34 owners want it
- Brass rod stem and Y34 plunger are the real wear parts
- Brass handle and material resist outdoor corrosion
- 4.6 ounces of metal — a substantial, factory-style part
- Buyers report the faucet runs properly again after install
What to watch
- Cut for the Y34 hydrant — not interchangeable with sillcock kits
- You need to know your hydrant model before ordering
Best matched to: Y34 hydrant owners who need a new plunger and stem in brass.
Not the one for: Model 17, 24 or 25 faucets — the plunger is the wrong shape.
5. Woodford Wall Hydrant Repair Kit For Model 17 RK-17MH
The genuine RK-17MH that has rebuilt more Model 17 sillcocks than anything else on this list.
If you want the safest possible bet for a Model 17 outside faucet, this is it. The Woodford RK-17MH is the factory rebuild valve kit, with a polished brass lever handle and every piece needed for a complete rebuild. Installation is a wall mount with a single hole, and the whole kit weighs just 1.6 ounces — small enough to fit in a shirt pocket.
The reason it stands out is the sheer track record. It is the most-reviewed kit in this lineup, and the consensus is that it stops leaks on faucets that have been outside for 15 years or more. Owners routinely describe a complete rebuild finished in about 15 minutes, with all the necessary pieces in the bag so nothing is missing mid-job. For a faucet that will not shut off, that completeness is the whole point.
The one caution is fit. This is the Model 17 kit, and only the Model 17. It will not go into a 24, 25 or Y34 body. That said, if yours is a 17, this is the part that matches the faucet off the shelf.
The experience dividend: this is the most-reviewed Model 17 kit in the lineup, and the pattern of owner feedback is consistent — leaks stop, all parts are present, a rebuild takes around 15 minutes.
The single caveat: it is cut for Model 17 only, so cross-fitting to a 24, 25 or Y34 will not work.
Reach for this if: you want the Model 17 rebuild kit with the deepest owner track record and a factory brass handle.
Hold off if: you are unsure which faucet you have — confirm the model stamp first.
6. RK-17MH Repair Kit Woodford Model 17
The fast swap for a spinning metal handle — owners describe a fix inside ten minutes.
When the complaint is a loose handle rather than a leaking body, this kit is aimed straight at it. It is a Model 17 compatible rebuild kit with a metal lever handle and a centerset install, and at 2.4 ounces it carries a bit more handle metal than the 1.6-ounce genuine RK-17MH. The brass colors it nicely, with an unfinished finish so it looks like the original hardware.
Speed is the real story here. The pattern of owner feedback is that the swap takes around ten minutes, and the kit works on old faucets that have started leaking at the packing. For a quick Saturday job, ten minutes is the number that matters.
The honest note is value. Some Model 17 owners feel it is a little pricey for what is inside the bag compared with the genuine Woodford kit. If cost is the deciding factor and you have time to wait, the factory part warrants a look. If you want the fast handle fix and the metal lever, this does the job.
Speed over depth: a metal lever handle and centerset install that owners mention installing in about ten minutes, with a 2.4-ounce weight that sits above the genuine RK-17MH’s 1.6 ounces.
Value is the question: some owners feel it is pricey for the contents — the genuine Woodford kit is the cost-conscious alternative if you can wait.
Ideal for: a Model 17 with a loose handle and a leak at the packing that you want fixed in one short session.
Different pick if: price is your main concern — the genuine RK-17MH carries the factory name.
7. Woodford RK PRV Adj Pvr Rod Kit
The winter-protection part that stops a frost-proof faucet from splitting when the temperature drops.
Not every repair kit fixes a drip — some prevent a burst. This is the adjustable rod with a pressure relief valve, and its job is to let the faucet drain back so the body does not burst when temperatures fall. It is made of brass, and the kit weighs 9.6 ounces, which tells you it is a longer metal rod rather than a bag of rubber seals.
That weight is the biggest gap in the whole lineup: at 9.6 ounces, this rod kit is far heftier than the 1.44-ounce RK-25 head kit. The rod is adjustable, so it fits both the Woodford Model 14 and Model 17 faucets — good if you have a mix of faucets on the property and cannot remember which is which. Owners describe fitting it to Model 14 and 17 faucets and reporting no leaks afterward, with the instructions clear enough to follow.
Here is where it differs from the handle kits: it does not replace the handle or the packing. It replaces the pressure relief side. If your faucet sputters or weeps at the vacuum breaker, or you want to dial in the drain-back for winter, this is the part. If your handle spins, you want one of the rebuild kits instead.
The frost-side fix
- Adjustable rod fits both Model 14 and Model 17 faucets
- Pressure relief valve guards against a split body in a freeze
- Brass construction, 9.6 ounces — a substantial metal part
- Customers note a leak-free result after fitting it
- Clear instructions in the bag
What it will not do
- It is not a handle or packing kit — a spinning handle needs a rebuild set
- At 9.6 ounces it is the heaviest kit here, so it is a rod, not a small bag of seals
Choose it for: a Model 14 or 17 faucet that weeps at the vacuum breaker or needs winter drain-back protection.
Choose a rebuild kit instead if: your handle spins and the leak is at the packing.
8. Eagle Mountain Products RK-17MH Woodford Model 17 Repair Kit
A brass-handled Model 17 kit that throws in the V8 float, handle screw and check valve.
This is the fullest Model 17 bag on the list. It carries the V8 float kit, handle screw, metal handle, packing nut, packing, packing washer and the check valve — everything to rebuild the head plus the vacuum breaker float in one order. It is lead-free, with a polished brass finish and a brass lever handle.
The footprint gives it away as a full-head kit: 8 inches deep, 4.75 inches wide and 1.7 inches high, roughly double the depth of the compact RHWRK17 sillcock bag. That extra room holds the handle and float alongside the seals. Installation is a single-hole wall mount, so it drops straight into the existing faucet body.
There is one setup step Woodford itself recommends: run the faucet first to confirm the vacuum breaker works without leaks before you install the kit. It is a small check that saves a second trip. The kit is cut for the Model 17, so the same model rule applies — a 24 or 25 will not take these parts.
Most parts in the bag: the V8 float kit, brass handle, packing nut and check valve together make this the most complete Model 17 kit here.
One pre-check first: operate the faucet to verify the vacuum breaker works before installing — and remember the parts fit the Model 17 only.
Go for it when: you want a Model 17 rebuild that includes the vacuum breaker float and a brass handle in one bag.
Pause if: your hydrant is not a Model 17 — the float and stem will not seat.
9. RK-25 Repair Kit Woodford Model 20 25 27
One bag that covers the Model 20, 25 and 27 freezeless series instead of a single stamp.
Here is the kit for the person who owns more than one Woodford faucet and does not want to buy a separate bag for each. This RK-25 service kit lists compatibility with the Model 20, 25 and 27 series freezeless wall faucets. Inside: a handle screw, wheel handle, head nut, drain guard, headnut gasket, stem screw, drain valve assembly and plunger assembly — eight parts built to match the original specifications.
The materials are chosen for outdoor duty. The brass exterior finish resists corrosion and weather, and the nitrile valve (a synthetic rubber rated to hold up to heat and frequent use) keeps the seal tight through repeated cycles. The kit weighs 5.9 ounces — heavier than the 1.44-ounce genuine RK-25, because this bag carries the wheel handle and the full drain valve assembly together. The seller also offers email support for install questions.
The honest note is the fit discipline. Because it is a multi-model kit cut to match the Model 20, 25 and 27 series, it is not a universal kit and will not go into a Model 17 or 24 faucet. If yours is one of those three freezeless series, this is a smart one-bag rebuild.
One bag, three models: covers the Model 20, 25 and 27 freezeless series with eight parts, a brass finish and a heat-resistant nitrile valve — 5.9 ounces total.
Not universal: those three series only; a Model 17 or 24 owner needs a different kit.
Worth it for: owners of Model 20, 25 or 27 freezeless faucets who want a full eight-part rebuild in one order.
Wrong fit for: Model 17 sillcocks and Model 24 faucets.
Know the Specs
Replacement part number (RK-17MH, RK-24, RK-25)
The part number is the key to the whole purchase. RK-17MH rebuilds the Model 17 outside wall faucet; RK-24 fits the Model 24; RK-25 fits the Model 25 freezeless series. Match the number to the stamp on your faucet body, and the parts will seat. Get it wrong, and the stem length or plunger shape will not line up — a common reason a repair kit “does not work.”
Vacuum breaker float and check valve
The vacuum breaker stops dirty water from being pulled back into your supply line when a hose is attached. Its float and check valve are the parts that wear out first. A kit that includes the float — like the V8 float kit in the Eagle Mountain RK-17MH — rebuilds that whole section rather than just the handle end. If the faucet spits or weeps at the top, the float is usually the culprit.
NBR and nitrile seals
NBR and nitrile both mean the same family of synthetic rubber: it resists heat, stays flexible in cold, and holds a seal better than plain rubber. More seals in the bag means more chances to stop a slow drip before it returns. Kits that list 3 NBR seals plus a check valve seal are built to survive freezing nights outside.
Pressure relief valve and adjustable rod
A frost-proof faucet relies on draining water back out of the body after each use. The pressure relief valve and adjustable rod do that draining. When they fail, trapped water can split the faucet body in a freeze. If your faucet weeps at the vacuum breaker or will not drain back, the rod-and-PRV kit is the part to replace — not the handle.
Common Questions
How do I know which Woodford repair kit fits my faucet?
Will an RK-17MH kit fit a Model 25 faucet?
How long does it take to rebuild a leaking outside faucet?
Do I need to shut off the water before installing a repair kit?
What is a vacuum breaker float and why does my kit include one?
Should I buy a genuine Woodford kit or a compatible one?
What is the difference between an RK-17MH and an RK-25 kit?
Will a repair kit fix a faucet that was installed 15 or 30 years ago?
Can I use a repair kit on a faucet with a pressure relief valve?
What if my kit has extra parts left over after installation?
The Bottom Line
For most Model 25 owners, the strongest pick is the Model 25 Repair Kit RK-25 because it rebuilds the entire head in an 8-piece bag rather than patching one seal. If your faucet is a Model 17 and you want the deepest track record, the Woodford RK-17MH is the safest pair of hands in the lineup. And for a frost-proof faucet that weeps at the vacuum breaker, the RK-ADJ-PRV rod kit fixes the winter drain-back side without touching the handle.
One nudge before you order: confirm the model stamp on your faucet body, because every kit here is cut for a specific Woodford series and the wrong number means a wasted trip to the hardware store.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.