Cobalt M42 high-speed-steel bits are the right choice for drilling stainless steel, because cobalt stays hard at the high temperatures stainless generates, while titanium coating only protects the surface.
Stainless steel fights back. Push a standard general-purpose bit into it and the metal hardens under the rubbing, the bit dulls, and you end up pressing harder on a hole that keeps getting tougher. The bit material decides whether that happens: cobalt-alloy steel holds its edge at drilling temperatures that wipe out ordinary high-speed steel, and it keeps that edge after resharpening because the cobalt runs through the whole bit rather than sitting on top as a coating.
The sections below cover which bit to buy, why cobalt outlasts titanium in this specific job, and the drilling method that keeps stainless from work-hardening before you finish the hole.
Cobalt or Titanium: What Actually Decides The Outcome
Cobalt is alloyed into the steel, so the cutting edge stays heat-resistant as it wears down; titanium nitride is a surface coating on high-speed steel, and once it wears through at the tip, the underlying bit behaves like ordinary HSS. Bosch markets its M42 cobalt line as containing 8% cobalt and engineered for stainless steel, cast iron, titanium, and other hard metals, citing very high drilling temperatures as the working condition it was built for.
That is a real gain for light work. It is not the same thing as a bit that survives repeated holes in thick stainless.
Two practical differences matter more than the marketing:
- Resharpening. A worn cobalt bit can be reground and keeps its heat resistance. Grinding a TiN bit removes the coating at the cutting edge, which is exactly where you needed it.
- Heat under load. Stainless work-hardens when a dull edge rubs instead of cuts. Cobalt tolerates that heat far better, so the bit keeps cutting and the metal stays soft enough to finish.
Watch for one labeling trap: a “titanium” drill bit is titanium-nitride-coated high-speed steel, not a titanium-alloy cutting tool. Bosch’s TiN products follow that pattern, and the coating is measured in microns.
Which Bosch Cobalt Bit Fits Your Job
Bosch’s M42 cobalt family runs from 1/16 inch to 1/2 inch, with the 1/2-inch CO2159B measuring 4 inches of working length and 6 inches overall. Bits 3/16 inch and larger get a three-flat shank to cut slipping in the chuck, and the split point starts the hole without skating.
The table below maps common stainless jobs to the model numbers worth ordering.
| Job On Stainless | Bosch Bit To Get | What You’re Getting |
|---|---|---|
| Everyday range of hole sizes | CO14B (M42 14-piece set) | 1/16 through 1/2 inch, split point, three-flat shanks on larger sizes |
| Wide range plus spares | CO21B (M42 21-piece set) | Duplicate small sizes and coverage through 1/2 inch |
| A single large hole | CO2159B, 1/2 inch M42 | 4-inch working length, 6-inch overall, three-flat shank |
| Occasional thin-gauge sheet | TI2142 TiN, 15/64 inch | 3-7/8 inch length with 3/8-inch reduced shank |
| Impact driver work | TI5IM or TI9IM TiN sets | Five or nine bits with impact-rated hex shanks |
| Mixed shop stock | CO2131–CO2159 standard cobalt | Individual sizes from 1/64 to 1/2 inch across 53 catalog options |
| Bulk replacement | CO4128–CO4159 bulk cobalt | Same cobalt line in jobber quantities |
How To Drill Stainless Without Ruining The Bit
Slow speed, firm continuous pressure, and cutting fluid get you a clean hole; high speed with light pressure is what work-hardens stainless and turns a five-minute job into a burned bit. The goal is substantial chips flying, not fine dust and heat.
- Clamp the workpiece. A part that shifts mid-hole breaks bits.
- Mark the spot and start with the split point or a center punch so the bit does not skate across the surface.
- Run the drill slowly and lean into it. Keep the bit cutting — rubbing is the enemy.
- Add cutting fluid and keep it wet. On deep holes, back the bit out periodically to clear chips and re-wet the tip, then resume on the same line.
- Enlarge gradually. If you need a pilot hole, start with a small cobalt bit and step up rather than opening with the final size.
Skip hammer mode on ordinary metal bits — that setting is for masonry. If you are running an impact driver, use only impact-rated hex-shank bits like the TI5IM and TI9IM sets, and check that your chuck or driver matches the shank before you start.
Safety basics apply throughout: eye protection, sleeves and hair secured, and stainless swarf controlled, because those chips come off sharp and hot. Let the bit and the part cool before you handle either.
For a side-by-side look at specific bits tested on stainless, our tested stainless steel drill bit roundup covers the models worth comparing.
Before you commit to one family, it helps to read Bosch’s own Cobalt M42 drill bits specification page, which lists diameters, lengths, and shank details for the full line.
When Titanium Still Makes Sense
Titanium nitride bits are a reasonable buy for the occasional hole in thin sheet or light-gauge stainless, where cost and convenience outweigh long-term edge life. Bosch’s TiN line is the lighter-duty option in its catalog, and the coating genuinely reduces friction while it lasts.
Reach for cobalt instead when the stainless is thick, when you are drilling repeated holes, when the alloy work-hardens aggressively, or when heat buildup is the recurring problem. Keeping both in the shop is not a compromise — it is matching the bit to the job.
Different products, different test conditions — read them as directional, not as a single ranking.
Common Questions
Can I use a regular hardware-store bit on stainless just once?
You can, and you may get one hole out of it. Ordinary general-purpose high-speed steel dulls fast on stainless and tends to work-harden the metal as it rubs, which makes any second hole harder than the first. A single cobalt bit costs little more and will still be usable afterward.
Why does my drill bit barely make a dent in stainless?
Almost always heat and speed. Running the drill fast with light pressure polishes the surface and hardens it instead of cutting. Slow the drill down, press firmly enough to raise continuous chips, add cutting fluid, and keep the bit cutting rather than pausing to spin in one spot.
Do cobalt bits fit a normal drill chuck?
Bosch’s standard cobalt bits use cylindrical shanks built for three-jaw chucks, so they fit ordinary rotary drills and drill/drivers. The impact-rated TiN sets use hex shanks instead. Match the shank to your tool before drilling, since a hex bit in a standard chuck will not hold securely.
Sources
- Bosch. “Cobalt M42 Drill Bits” Lists M42 cobalt diameters, working lengths, and stainless-steel application claims.
- Bosch. “Cobalt Drill Bits” Catalog of standard cobalt models, sets, and bulk options.
- Bosch. “Titanium Nitride Coated Drill Bits” Specifications and coating claims for the TiN line.