Measure the finished, installed tub and wall opening in three places — bottom width at the tub ledge, top width at the jambs, and finished height — then match those figures to the door’s published installation range.
A sliding bathtub door that arrives half an inch too wide sits in the box while the tub stays unusable, and that failure almost always starts with a tape measure run against bare studs. Measurements for these doors are always taken on the finished opening — tile, wall panels, and the tub itself already in place — because tile thickness and a set tub change every number the door’s installation instructions care about. Kohler’s installation documentation says it plainly: the bath and finished wall material must be completely installed before the door is measured or hung.
The steps below follow the manufacturer sequence, and the one table covers the numbers worth writing down before you shop.
What Exactly Do You Measure On A Sliding Bathtub Door?
You measure three things: wall-to-wall width at the flat part of the tub ledge, wall-to-wall width at the top of the installed wall jambs, and finished height from the ledge to where the door terminates. No single number describes the opening, and treating the bottom width as the whole story is how doors get ordered wrong.
The bottom width is taken where the bottom track will actually rest — across the flattest portion of the tub ledge. If either corner where the tub meets the wall has a radius or an angle, measure above it at the flattest usable point, not diagonally across the curve. Kohler’s Sterling guide also calls for the track to sit on the flattest part of the ledge with its sloping face toward the tub interior, and for the gaps between the track and each wall to come out equal. Those conditions are worth checking with your tape before you commit to a width.
The top width is different, and this catches people. Sterling’s instructions say not to measure or cut the top track until the wall jambs are installed, because the top of the opening frequently does not match the bottom. Finished height runs from the tub ledge or threshold to the finished wall surface where the door ends — and that figure is model-specific, so it has to be checked against the door’s own specification sheet rather than assumed.
How Do You Take The Measurements In The Right Order?
Finish the bath and walls, then record width at the bottom, middle, and top of the opening and height on both sides — that repetition is what exposes out-of-square walls and openings that are out of plumb before the door shows up. One pass with the tape is not enough.
- Install the tub and finished wall material completely. Nothing gets measured on framing or on a tub that isn’t set.
- Measure the bottom opening wall to wall across the flat ledge, above any corner radius.
- Measure the middle of the opening as a cross-check against the bottom width.
- Install the wall jambs, then measure wall to wall at the top of the jambs.
- Measure finished height at both the left and right side.
- Write every number down and compare the full set against the door’s published range and height.
On a steel tape, remember the case has width — the Sterling guide warns about that — so read from the same reference point every time rather than letting the housing hang over an edge.
| What To Record | Where The Tape Goes | Why It Matters |
|---|---|---|
| Bottom width | Wall to wall on the flat tub ledge, above any radius | Sets the bottom track length and the door’s base fit |
| Middle width | Wall to wall mid-opening | Catches bowed or out-of-plumb walls |
| Top width | Wall to wall at the installed jambs | Top and bottom widths often differ |
| Finished height | Tub ledge to the finished wall termination | The required height is model-specific |
| Door’s stated range | Manufacturer spec sheet | |
| Door’s stated height | Manufacturer spec sheet | |
| Track cut allowance | That model’s own instructions |
Why The Cut Allowances Can’t Be Copied From Another Door
Track cut allowances are model-specific, and comparing across manufacturers proves it:
Four guides, four different sets of numbers. Applying one door’s allowance to a different door is a reliable way to end up with a track that’s too short or a panel that won’t clear. Read the allowance from the paperwork that came with your specific door, and if you’re still weighing options, this comparison of tested sliding bathtub doors lists published widths and heights so you can match a model to your opening before you buy.
Those are listed dimensions, not a promise that any door fits any 60-inch opening.
What Are The Most Common Measuring Mistakes?
Measuring too early and measuring a curve instead of a flat are the two that cause most of the trouble, and both are avoidable with the tape and the paperwork in hand. Sterling and Kohler’s guides collectively flag the same handful of errors.
- Taking numbers before tile, wall panels, or the tub finish is installed.
- Running the tape across a rounded tub corner instead of above the radius.
- Assuming the top, middle, and bottom widths are identical.
- Ignoring the tape case width when reading a steel tape.
- Cutting the top track before the wall jambs are installed and measured.
- Borrowing another model’s track-cut allowance.
Every number, cut allowance, and dimension that decides whether the door fits comes from the manufacturer’s own documentation for your model. Prices and current model listings weren’t verifiable from the official sources here, so check the retailer or manufacturer listing at the time you order.
Common Questions
Can I Measure Before The Tile Is Up?
No. Kohler’s installation documentation requires the bath and finished wall material to be completely installed first. Tile and wall panels add thickness that changes the wall-to-wall width, and an unset tub changes the height. Measuring on framing produces numbers that won’t match the finished opening, so wait until the surround is done.
Do I Measure Above Or Across A Rounded Tub Corner?
Measure above the radius at the flattest usable point on the ledge. Sterling’s guide specifies the track must sit on the flattest part of the ledge with the gaps to each wall equal, so a tape run diagonally across a curve reads a width the track can’t actually fit. Find the flat stretch and measure there.
Why Does The Top Width Differ From The Bottom?
Walls go out of plumb and openings go out of square, so the two rarely match exactly. Sterling’s instructions specifically prohibit measuring or cutting the top track until the wall jambs are installed and the top width can be read directly. Recording the middle width too is what reveals a bowed wall before installation day.
Sources
- Kohler. “Bypass Bath Door Installation and Specification Guide” Supports the 62-inch height, 56-5/8 to 59-5/8 inch width range, 3-inch adjustment, 1/16 inch cut allowance, and the requirement to finish the bath and walls before measuring.
- Kohler. “Bath Door Technical Specification Sheet” Supports the model-specific finished-height measurement from the tub ledge to the wall termination.
- Sterling (Kohler). “Sliding Bath Door Installation Instructions” Supports measuring above the corner radius, equal track gaps, the 1/32 inch top and 1-1/2 inch bottom cut allowances, the tape-case width warning, and measuring the top only after jamb installation.