A lowering kit install is a half-day job that hinges on correct fitment, torqued U-bolts, and clearance checks before the first test drive.
The costliest mistake in a lowering job happens while the truck is still on the ground: a kit that fits the year but not the cab, axle, or drivetrain. Every installation sheet opens with a fitment check for exactly that reason. Whether you’re working out how to lower a truck for stance or for cornering, the order below is the one that keeps the axle located, the brake hoses clear, and the hardware tight.
What Do You Need On Hand Before The First Bolt Comes Loose?
Five things: a kit confirmed for your truck’s year, cab, drivetrain, axle, and rear suspension type, plus a rated floor jack, jack stands, wheel chocks, and a 0–150 lb-ft torque wrench.
The truck sits on flat asphalt or concrete, chocked at the end you aren’t touching. Stands go under frame rails, never under the rear axle tubes, and the jack stays under the axle housing after the truck is up so the axle stays controlled when leaf-spring tension comes off. Eye and hand protection isn’t optional when you’re working underneath sprung weight.
Eibach’s installation documents also limit who should take this on, stating that only qualified mechanics experienced with suspension removal and installation should perform the work, with stands placed where the factory manual specifies. Kits differ because suspensions differ — what’s in the box depends on which end you’re dropping and how far.
| Component | What It Does | Where It Goes Wrong |
|---|---|---|
| Lowering springs | Cuts ride height while keeping the spring type | Paired with original shocks |
| Drop spindles | Drops the front and keeps spring travel | Spindle and brake combo mismatch |
| Rear blocks | Spaces the axle away from the leaf spring | Centering pin never seated |
| Shackles and hangers | Moves rear leaf mounting points | Contact with exhaust or bed floor |
| Axle flip kit | Relocates the axle above the leaf pack | Clearance that demands a C-notch |
| Matched shocks | Controls the shorter travel | Reusing OE shocks past their range |
| Frame C-notch | Restores clearance on deep drops | Skipped on builds that need it |
Lowering A Truck With Blocks: The Step Order That Works
- Lay out every listed part. Don’t start if hardware is missing.
- Chock the front wheels, raise the rear with a rated jack, and set stands under the frame rails.
- Keep the jack under the axle housing, then remove the original U-bolts and nuts.
- Move the axle slowly — up or down, depending on whether it sits above or below the leaf spring — until there’s room for the block.
- Set the block between leaf spring and axle housing. The spring center bolt must seat in the block recess, and the block’s centering pin must drop into the axle spring-perch hole.
- Lower the jack so axle weight rests on the block and spring.
- Reinstall the wheels, raise the truck, pull the stands, and set it down.
- Check brake hoses, ABS wiring, and lines for interference, then test-drive cautiously somewhere empty — handling will feel different.
You’ll know it seated correctly when the block sits flush with no gap at the spring pad and both U-bolts draw down evenly before the wrench clicks. Trucks with a rear load-sensing proportioning valve may need that valve readjusted to the manufacturer’s specification afterward, or rear braking pressure runs off. Belltech’s rear lowering block instructions cover the full sequence and the retorque schedule.
Front Springs, Shocks, And The Checks That Catch Mistakes
Front work carries tighter rules than the rear: certain springs cannot be run with original shocks, and shocks must never be disassembled or hit with an impact gun.
Eibach’s sheet for its PRO-TRUCK SPORT leveling springs states they must not be used with original-equipment shocks — extended-travel shocks are required to avoid suspension damage — and that they don’t fit airbag-equipped trucks where the application uses OE rear coil springs. Shocks come off using the factory procedure and go back in reverse order, with no impact tools on the piston rod, shaft, or piston-rod nut.
Once the truck is down, check tire-to-fender clearance, brake-line and ABS sensor routing, exhaust, fuel lines, and wiring for contact. Eibach calls for a fastener and clearance inspection after 10 miles, and an alignment follows any ride-height change — skip it and the truck wanders while the tires pay for it.
Haven’t bought parts yet? Our tested truck lowering kits roundup covers the options that fit common US trucks.
Before the first real drive, confirm:
- Every fastener torqued to factory or kit spec, with new hardware where the kit supplied it.
- Block centering pins and spring center bolts seated.
- Brake hoses and ABS wiring clear through full suspension travel.
- Alignment booked, and a retorque planned at 10, 100, and 1,000 miles.
Common Questions
How Much Drop Can Original Shocks Handle?
There’s no universal number, and that’s the point — the limit depends on your truck’s suspension design and how much travel is left. The dependable rule is that any spring designed to change ride height should be paired with shocks matched to that height. Eibach’s instructions explicitly bar original-equipment shocks with its PRO-TRUCK SPORT springs and call for extended-travel units.
Do You Need An Alignment After Lowering?
Yes. Changing ride height shifts camber, caster, and toe, and those angles decide how the truck tracks and how the tires wear. Eibach’s post-install checklist includes inspecting or adjusting wheel alignment along with tire-to-fender clearance and brake-line routing. Drive to the alignment rack before any long trip and keep the printout so you know the final numbers.
Are Rear Blocks Fine On A Daily Driver?
Blocks hold up fine when they’re the right height for the truck, the centering pin is seated in the spring perch, and the U-bolts are torqued and rechecked on schedule. Most failure stories trace back to a pin that never seated, reused U-bolts, or hardware nobody retorqued. Past a few inches of rear drop, frame clearance and pinion angle become the limit.
Sources
- Belltech. “Lowering Block Kit Installation Instructions.” Source for the rear block procedure, the 80 lb-ft U-bolt torque spec, and the 10/100/1,000-mile retorque schedule.
- Eibach. “Installation Instructions.” Source for shock handling cautions, OE shock pairing limits, and post-install clearance and alignment checks.