5 Best Table Saw Guard | Rip Hardwood Without The Kick

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

If your table saw has no riving knife and ripping hardwood makes you flinch, the fix is a splitter system that keeps the kerf open behind the blade. That single piece of steel is what stops the board from pinching the blade and launching back at your hands. This guide covers the five guards and splitters worth bolting onto your saw, who each one suits, and the installation headaches to expect before you drill a single hole.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

A splitter that sits a hair off-center causes the same binding it is meant to prevent, so fit and blade kerf (the width of the cut your blade makes) matter more than brand. Below are the honest differences between a bolt-on splitter and a full dust-collecting hood, so you can choose the right table saw guard for your saw, your blades, and the way you actually work in the shop.

Top Picks

MICROJIG GRR-RIPPER MJ SPLITTER Steel Pro SP-2
Best OverallMICROJIG GRR-RIPPER MJ SPLITTER Steel Pro SP-24.0+★500+ ratingsThe full-kerf splitter kit that turns a knife-less old saw into a safer ripping machine. Here is the number that justifies this pick: four splitters, each with a different built-in offset — 0.000”, 0.003”, 0.006”, and 0.009”.Check price on Amazon
SawStop Dust Collection Blade Guard Assembly TSG-DC
Dust Control PickSawStop Dust Collection Blade Guard Assembly TSG-DC4.0+★100+ ratingsA clear hood that swallows the sawdust and keeps your hands behind bars. For a SawStop owner tired of sweeping a snowdrift off the floor after every session, this assembly is the upgrade.Check price on Amazon

How To Choose The Best Table Saw Guard

The first thing to sort out is what your saw is missing. A cabinet saw with a factory riving knife may only need a better dust hood, while an older contractor saw with a bare blade needs a splitter drilled into a zero clearance insert. Buying the wrong type is the most common mistake, and it costs you a return label and a wasted afternoon.

Match the splitter to your blade kerf

Kerf is the width of the slot a blade cuts, and it is measured in inches. Full kerf blades cut a wider slot than thin kerf blades, so a splitter built for one will bind or float in the other. Check your blade before you buy. The MICROJIG Steel Pro full kerf kit is built around full kerf blades, while the thin kerf version exists for exactly this reason.

Decide if you need a splitter or a full hood

A splitter is a slim steel blade sitting right behind the saw blade, and it does one job: hold the cut open so the wood cannot pinch and kick. A full guard is a clear hood that surrounds the blade, collects dust, and adds anti-kickback pawls. Splitters suit ripping and joinery work where you need to see the blade. Hoods suit sheet goods and long rip cuts where dust is the bigger annoyance.

Check your insert and your saw size first

Most aftermarket splitters mount through a zero clearance insert, which is a throat plate you cut yourself so it hugs the blade. If your saw uses a proprietary insert, confirm the splitter will fit before ordering. Saw size matters too, because some splitters are sized for standard 10-inch saws and will not sit right on a 9-inch machine.

Side-by-Side Comparison

Model Best For Guard Type Blade Kerf Weight Amazon
MICROJIG GRR-RIPPER MJ SPLITTER Steel Pro SP-2★ Best Overall Older saws with no riving knife Splitter system Full kerf 6.4 ounces Amazon
SawStop Dust Collection Blade Guard TSG-DCDust Control Pick Dust control on a SawStop Full hood guard — — Amazon
MICROJIG MJ SPLITTER Steel Pro SP-2TK Thin kerf blades Splitter system Thin kerf 0.16 kg Amazon
PSI Woodworking TSGUARD Overhead dust collection Overhead hood guard Up to 16″ blades 41.1 pounds Amazon

Detailed Reviews

★ Best Overall

1. MICROJIG GRR-RIPPER MJ SPLITTER Steel Pro SP-2

Our pick — 4.0+★ from 500+ verified ratings; the strongest balance of quality and price.

Four Steel-Core SplittersKerf Keepers Included

The full-kerf splitter kit that turns a knife-less old saw into a safer ripping machine.

Here is the number that justifies this pick: four splitters, each with a different built-in offset — 0.000”, 0.003”, 0.006”, and 0.009”. That offset is a tiny sideways step machined into the splitter, and it lets you dial the fit to your exact blade so the splitter lines up instead of fighting the cut. You get a steel core wrapped in an ABS polymer shell, and the whole assembly weighs 6.4 ounces. It is a safety upgrade aimed squarely at saws that never had a riving knife, and it works with all full kerf blades.

What wins people over is the safety side of the system — holding the kerf open and keeping stock tight to the fence so a rip does not close up behind the blade and grab. The four Kerf Keepers have a stated kerf range of 0.118” to 0.145”, and they are designed to eject if the wood closes on the blade rather than bind it. The kit also arrives complete: four splitters, four Kerf Keepers, a drill guide, a 3/16” drill bit, and screws, so there is no second trip for hardware. This is the version to buy over the budget SP-0125 below if you run full kerf blades. It also wins on size for the money — at 4”L x 0.5”W x 4”H it is a compact piece of hardware, and the setup suits a shop-made zero clearance insert.

The catch is installation, and the honest framing is that this is a fit-and-drill job, not a clip-on. Mixed feedback on function and quality is the pattern here, which mostly comes back to how carefully the holes are placed in the insert — measure twice and drill once. It is also explicitly a fix for saws without a riving knife; if yours already has one, this is redundant. Think of it as the right tool for an older machine and the wrong one for a modern cabinet saw.

What earns its place in the shop

  • Four offset splitters (0.000” to 0.009”) let you tune fit to your blade
  • Kerf Keepers rated for 0.118” to 0.145” kerf eject instead of binding
  • Complete kit: drill guide, 3/16” drill bit, and screws in the box
  • Only 6.4 ounces, so it adds nothing to the saw

Where it asks for patience

  • Drilling the insert yourself means the result depends on your hole placement
  • Built for saws without a riving knife — redundant on a saw that has one
  • Full kerf only; thin kerf blades need the separate SP-2TK kit

The right buyer: anyone running an older full kerf saw with a bare blade and a zero clearance insert ready to drill.

The honest cost: your accuracy at the drill press decides how well it performs.

Dust Control Pick

2. SawStop Dust Collection Blade Guard Assembly TSG-DC

1.5″ Dust PortAnti-Kickback Pawls

A clear hood that swallows the sawdust and keeps your hands behind bars.

For a SawStop owner tired of sweeping a snowdrift off the floor after every session, this assembly is the upgrade. The hood surrounds the blade so dust gets captured instead of thrown, and it connects through a 1.5” dust port you hook to your collector. Performance is the part that carries this pick — it is the most praised element of the guard, with dust collection close behind. The clear plastic body keeps the cut line visible while the guard does its work.

Independent lateral guards narrow the blade opening so you can make cuts as narrow as 3/4”, and integrated anti-kickback pawls add a second layer of protection on top of the splitter. The limiting rod comes included with the guard, so the assembly is complete as shipped. Nothing on this item changes the saw’s own safety system — it sits above the table and improves what you already have.

Fit is the thing to check carefully. It is engineered for SawStop saws, and the feedback splits between owners who found it a perfect match and those whose needs it did not meet, so confirm your specific model before ordering. Value is the other split — dust collection hardware is not cheap, and some owners feel the price sits high for what is essentially a hood. The trade-off worth naming is that a full hood gives you less clear sight of the blade than a bare splitter does.

Best reason to buy: above-table dust capture with a 1.5” port and pawls that work alongside your saw’s own system, all in a clear housing you can see through.

Check before you click: it is SawStop-specific, so this is the wrong guard for any other brand of saw.

Reach for this if: you own a SawStop and the dust is the daily irritation.

Pass if: your saw is a different make — the mounting simply will not line up.

Thin Kerf Pick

3. MICROJIG MJ SPLITTER Steel Pro SP-2TK

Thin Kerf SplittersSteel-Reinforced Core

Same steel-core idea as the top pick, reshaped for the thin kerf blades in your drawer.

If your ripping blade is thin kerf, this is the sibling kit you actually need, because the full kerf version will not seat correctly. You get four thin kerf splitters, four Kerf Keepers, the precision drill guide, a 3/16” drill bit, and screws. The build is a polycarbonate shell reinforced with a stainless steel core, and the shell is what holds stability under cutting pressure when you are working through hardwood, sheet goods, or plain lumber. The drill guide registers off the kerf itself, which centers the bit for you rather than leaving you to eyeball it.

Performance is what this kit is known for, and quality sits right next to it as the second-most praised trait. The dual splitter setup holds the cut open on both sides for a smoother rip, and the splitters install behind the blade to keep the workpiece against the fence. That combination is the whole anti-pinch story: less pinching means less chance of a kick. At 0.16 kg the hardware is light enough that you will not notice it once installed.

The honest trouble spot is hole alignment — reports of the holes sitting too far apart and not lining up are the recurring complaint, and installation feedback runs mixed as a result. That is a placement problem rather than a design flaw, but it means you should drill carefully and test-fit before committing. Compare it to the SP-2 above: both are 4”L x 0.5”W x 4”H and both carry a steel-reinforced construction, but this one is the correct choice for thin kerf and the wrong one for full kerf.

What it does well: thin kerf splitters with a kerf-registered drill guide, so the cut stays open on both sides of the blade during a rip.

The honest caveat: hole placement is fussy, and a mis-drilled insert will not hold the splitter straight.

Made for: the woodworker whose blades are all thin kerf and who wants the same system as the top pick in the right size.

Not for: full kerf blades, which need the standard Steel Pro kit instead.

Overhead Option

4. PSI Woodworking TSGUARD Table Saw Dust Collection Guard

Boom Extends to 83″4″ Dust Hose Connection

The ceiling-mounted hood that swings in over the blade and takes the dust with it.

This is a different animal from the splitters, and buyers should understand that before ordering. It is an overhead guard on an articulating boom that extends up to 83” and can be mounted to the ceiling for maximum clearance. The hood connects to any standard 4” dust collection hose or ductwork, and it captures the dust thrown up by the blade rather than letting it settle on your work. It accepts saw blades up to 16”, tilts for 45 degree cuts, and adjusts to suit the thickness of the material you are cutting.

Two things make it genuinely useful in a small shop. First, it swings out of the way when a job does not call for it, so it is not a permanent obstruction. Second, the size difference between this and the splitters — 47.3”L x 12.8”W x 6.5”H against the 4”L x 0.5”W x 4”H MICROJIG Steel Pro — tells you this is a mounted piece of shop equipment rather than pocket hardware. It is well made and easy to use, and the value read is positive.

Weighing 41.1 pounds, it needs a solid mounting point overhead, so plan your ceiling anchor before it arrives. The replacement clear dust collection hood is available separately as TSGUARD-DH if the original ever takes a hit. A couple of owners note it works better on contractor or cabinet saws than on other setups, so check that your saw is the right style. The important distinction: this hood controls dust and adds a physical barrier, but it does not replace a splitter for anti-kickback duty.

A hood that clears the shop air

  • Boom reaches up to 83” and swings away when not needed
  • Connects to any standard 4” dust hose or ductwork
  • Handles blades up to 16” and tilts for 45 degree cuts

What you sign up for

  • 41.1 pounds of equipment needs a solid ceiling mount
  • Dust and barrier duty only — a splitter is still your kickback defense
  • Suited to contractor or cabinet saws rather than every table saw style

Choose this when: the dust cloud is the problem and your ceiling has a place to hang a boom.

Look elsewhere when: you are shopping for anti-kickback protection, which this guard does not provide on its own.

Know the Specs

Kerf and why it decides the fit

Kerf is the width of the slot a blade cuts, and it is the single most important number when picking a splitter. Full kerf blades cut a wider slot than thin kerf blades, so a splitter built for one will bind or fail to hold in the other. The MJ SPLITTER Steel Pro kits come in two versions for exactly this reason — the standard kit for full kerf blades and the TK kit for thin kerf. Check the blade on your saw before you order anything.

Splitter offset and kerf keepers

Offset is a tiny built-in sideways step on a splitter, measured in thousandths of an inch, that lets you align it precisely to your blade. The Steel Pro full kerf kit ships offsets of 0.000”, 0.003”, 0.006”, and 0.009” so you can pick the one that lines up. Kerf Keepers are small guards rated for a kerf range of 0.118” to 0.145”, and they are designed to eject if the wood closes on the blade instead of jamming it. Together they hold the cut open through a rip.

Zero clearance inserts explained

A zero clearance insert is a throat plate you cut yourself so the slot hugs your blade with no gap. Most aftermarket splitters, including the SP-0125, mount straight into phenolic, wood, or plastic inserts. That is why a drill guide comes in the box — you drill the mounting holes yourself. The precision of those holes decides how well the splitter lines up, which is the single biggest variable in how the finished install performs.

Dust ports and boom reach

Dust collection is a separate job from kickback control, and the numbers tell you what you are getting. The SawStop guard uses a 1.5” dust port and sits directly above the blade. The PSI TSGUARD connects to any standard 4” dust collection hose or ductwork and hangs from a boom that extends up to 83”, so it can mount to the ceiling and swing out of the way. A bigger port and hose move more air, but both need a collector behind them to pull the dust through.

Common Questions

Will a splitter fit my table saw if it has no riving knife?
Yes — that is exactly the saw the MICROJIG Steel Pro kits are built for. They are described as a safety upgrade for saws without a riving knife, and they mount through a zero clearance insert you drill yourself. If your saw already has a factory riving knife, a splitter is redundant.
What is the difference between full kerf and thin kerf splitters?
It depends on the width of the slot your blade cuts. The standard Steel Pro kit is designed for full kerf blades, and the SP-2TK exists specifically for thin kerf blades. Installing the wrong one means the splitter will not seat in the cut properly, so match the kit to the blade you actually run.
Do I need a zero clearance insert to install a splitter?
For most aftermarket splitters, yes. The SP-0125 installs directly to phenolic, wood, or plastic zero clearance inserts, and the Steel Pro kits come with a drill guide and drill bit so you can cut the mounting holes in your own insert. A standard slotted throat plate will not hold the splitter firmly.
Does a blade guard replace the need for a splitter?
No. A hood like the SawStop assembly or the PSI TSGUARD covers the blade and collects dust, and the SawStop guard adds anti-kickback pawls, but the splitter is the part that physically holds the kerf open. If kickback is your worry, the splitter is still the piece doing the work.
Can the PSI TSGUARD be used with any table saw?
It mounts overhead rather than to the saw itself, so it is more flexible than a blade-mounted guard, but it is noted as working better on contractor or cabinet saws. It also weighs 41.1 pounds, so you need a solid ceiling anchor. Measure your clearance before mounting the boom.
Why do my splitter holes not line up with the insert?
Hole placement is the recurring frustration with drilled installations, and the SP-2TK draws specific complaints about holes sitting too far apart. The drill guide is there to register the bit off the kerf and center it, so use it carefully and test-fit before you commit. A mis-drilled insert can be remade, but the splitter will not hold straight in a bad one.
How much does a splitter weigh and does it matter?
The splitters here run from 1.6 ounces for the SP-0125 up to 6.4 ounces for the Steel Pro full kerf kit. Weight does not affect the cut much, but it is a fair proxy for how much steel you are getting. The lightweight budget kit is the one with durability named as its weak point.
Will the SawStop guard fit a non-SawStop table saw?
It is engineered specifically for SawStop saws, and the mounting is built around that saw series. Fit feedback is split even among SawStop owners, so confirm your exact model before ordering. On a different brand, the assembly is unlikely to mount correctly.
Can I use a guard and a splitter together on the same saw?
Yes, and that is the setup many shops run. The splitter sits behind the blade holding the kerf open, while an overhead hood like the PSI TSGUARD handles the dust and adds a physical barrier above the table. They perform different jobs, so pairing them covers both kickback and dust.
Is the splitter warranty affected by where I buy it?
On the SP-0125 and the Steel Pro kits, the extended 3-year manufacturer warranty is offered from authorized dealers only. Buying from an unauthorized seller can leave you without that coverage. It is worth checking the seller before you order, especially on the budget kit.

The Bottom Line

The one to start with is the MICROJIG GRR-RIPPER MJ SPLITTER Steel Pro SP-2, because the four offset splitters and the kerf-rated keepers give you a properly aligned setup on a saw that never had a riving knife (the blade-thickness fin that stops kickback). If your blades are thin kerf, the SP-2TK is the same idea in the right size, and it is the pair to note against the standard kit — same 4”L x 0.5”W x 4”H footprint, different blade fit. For dust rather than kickback, the SawStop TSG-DC handles the mess on a SawStop, and the PSI TSGUARD takes the overhead route if your ceiling has room for a boom.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top