Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your Whirlpool fridge is running warm, humming louder than it used to, or the fan behind the freezer wall has stopped turning, you almost certainly do not need a new refrigerator. You need the right condenser fan motor, matched to the part number your fridge was built around. The tricky part is that Whirlpool used several different motors across its model lines, and the wrong one either will not spin or will spin at the wrong current draw. This guide covers seven real replacements, what each one actually fits, and how to pick the one that matches your appliance instead of guessing.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
A condenser fan motor is the small electric motor that turns the fan blade and pushes air across the condenser coil, which is how your fridge dumps heat. When it fails, cooling drops and the compressor works harder. Below you will find the exact part numbers, voltages, and wattages so you can match your model before you order the best Whirlpool Refrigerator Fan Motor for your appliance.
Top Picks


How To Choose The Best Whirlpool Refrigerator Fan Motor
You are not shopping for a gadget here. You are matching a part. The motor you order has to spin the existing fan blade, plug into the existing harness (the wiring connector) or accept your old wires, and draw the same current (the electrical load, measured in amps) as the motor it replaces. Get any of those three wrong and the fridge stays warm. So the whole buying decision depends on matching numbers, not brands or marketing.
Start With The Part Number On Your Old Motor
Pull the old motor and read the sticker on its housing. That number is your anchor. The seven picks here cover the common Whirlpool family part numbers — W10128551, W10124096, W10130108, W10204250, 833697, and 2188874 — and most listings cross-reference a long list of superseded numbers so you can find your match. If your number is not in a listing’s cross-reference list, that listing will not work for you.
Match The Voltage And The Current Draw
Whirlpool condenser motors in this group run on either 115 volts or 120 volts, and that difference matters less than the amp rating. One kit here is explicit that a 78mA fan motor will not run correctly on its 115V, 4.1W design and may fail to start because of a load mismatch. So check the current rating on your old motor’s label, not just the voltage.
Count The Terminals And The Wires
Some of these motors are 2-wire units, and one is a 4-pin connector design. That is not a style preference; it is a hard fit requirement. If your original motor has 3 terminals, one listing here specifically tells you to order the W10204250 part instead. Count your connector pins and wire count before you order anything.
Decide if you want A Kit Or Just The Motor
A kit bundles the motor with the fan blade, wire harness, and mounting screws. That saves you from reusing a cracked blade or hunting for a harness that no longer clips in. If your old blade and harness are in good shape, a bare motor is fine. If you are unsure, a complete kit removes a variable.
Side-by-Side Comparison
| Model | Best For | Voltage | Wattage | Kit Contents | Amazon |
|---|---|---|---|---|---|
| LinkEZ W10128551★ Best Overall | Broadest model coverage | — | — | Motor | Amazon |
| Blutoget W10124096Best Value | Complete kit on a budget | 115 volts | 4.1 watts | Motor, blade, harness, 6 screws | Amazon |
| Supco SM5109 | Older Whirlpool and Kenmore fridges | 120 volts | 2 watts | Motor | Amazon |
| TOMOON W10124096 | Full kit with explicit amp warning | 115 volts | 4.1 watts | Motor, ABS blade, harness, screws | Amazon |
| BlueStars 2188874 | 4-pin connector models | 115 volts | 4.1 watts | Motor | Amazon |
| Edgewater W10124096 | Fast, simple install | 120 volts | — | Motor, blade, harness, screws | Amazon |
| Whirlpool Genuine OEM | Exact factory replacement | 115 volts | 4.1 watts | Motor, blade, harness, hardware, instructions | Amazon |
Detailed Reviews
1. Refrigerator Fan Motor W10128551
Our pick — 4.5+★ from 200+ verified ratings; the strongest balance of quality and price.
The one that fits across more Whirlpool-family fridges than anything else here.
Fridge model hunting is the real job before you buy a motor, and this one takes most of it off your plate. The W10128551 is listed as compatible with 2500+ models of Whirlpool and its affiliated brands — Amana, Crosley, Inglis, Jenn-Air, KitchenAid, and Maytag — and it also crosses over to 600+ Kenmore models. If your sticker number lands anywhere in that spread, you have a match without hunting further.
The listing is honest about the limit: it publishes the full compatibility list and tells you plainly that if your model number is not on it, the part will not work for you. It also claims exact OEM fit, form, and function, so the dimensions mirror the factory part rather than approximating it. The motor weighs 0.41 kg, and the cross-reference covers W10128551, WPW10128551, 10449508, W10449515, and the 6700-series numbers. This is the crowd favorite, holding 4.5+ stars across 240+ ratings — the strongest combination of score and volume on this list.
What wins people over is reliability, and it wins by a wide margin. Reviewers repeatedly describe this motor still running after three years of service. Replacement quality is the next thing owners point to, followed by value. Quiet operation comes up too, which matters because a failing condenser motor (the fan that cools the compressor coils) is usually heard before it is diagnosed. The one thing you should know going in: this listing is the motor only, so if your fan blade is cracked or the harness is brittle, you will need to source those separately, where the Blutoget kit below gives you everything in one box.
Where it earns its place
- Compatibility spans 2500+ Whirlpool-family models plus 600+ Kenmore models, so fit uncertainty drops sharply
- Reliability is the most-praised trait of this part, with owners reporting multi-year service
- Runs quietly — a meaningful point when the old motor failed loudly
- Exact OEM fit, form, and function claimed, so the housing and shaft line up with the factory part
What to know before ordering
- Motor only — the fan blade and harness are not included
- If your model number is absent from the published list, this part is not for you
Buy this one if: you know your fridge model number and want the widest safety net plus the steadiest long-run reputation on the list.
Look elsewhere if: your fan blade is already cracked, since you would be buying the blade separately anyway.
2. Blutoget W10124096 Condenser Fan Motor Kit
Everything in the box, so you are not reusing a twenty-year-old fan blade.
The W10124096 kit solves the annoying part of fridge repair: hunting for the blade, the harness, and the right screws while the fridge sits warm. You get 1 x fan motor, 1 x fan blade, 6 x screws, and 1 x wire harness in a single order. The motor itself is a 2-wire unit rated at 115 volts, 4.1 watts, and 60Hz, with a 1/8″ x 1-1/4″ shaft. Compare that to the Supco SM5109 further down, which is a 2-watt, 120-volt motor — the Blutoget draws 4.1 watts against the Supco’s 2 watts, so the two are not a like-for-like swap.
Owners describe the swap as a quick job. Buyers report a perfect fit and an easy install, with one customer finishing the replacement in under 15 minutes. You will want a small socket set, a flat tip screwdriver, and needle nose pliers on hand, and Blutoget tells you to kill the power and wear gloves first. The housing is metal with ABS components (a hard plastic), and the rubber coils are built to resist cracking. Blutoget backs it with 365 days of after-sales service, which is a longer stated window than most listings here offer.
The honest caveat is fitment scope. This is a W10124096-family replacement, and the listing names Whirlpool, Kenmore, GE, Amana, KitchenAid, and Maytag refrigerators with a long cross-reference list including W10130108, AP4318657, PS1957416, and W10204250. If your motor is a 4-pin connector design instead, the BlueStars pick below is the one you want. Functionality is what owners praise most here, with fit close behind — the feedback reads like a part that does exactly what it says on install day.
Kit math: motor, blade, harness, and six screws in one order beats buying four pieces separately and hoping the blade matches the shaft.
The trade-off: it is a W10124096-family part, so a fridge built around a different number — especially a 4-pin design — will need a different motor entirely.
Reach for this if: your old motor is in the W10124096 family and you would rather swap the whole assembly than clean up the old blade.
Think twice if: you have not confirmed your motor’s part number — this one’s cross-reference list is long, but it is not universal.
3. Supco SM5109 Refrigerator Condenser Fan Motor
A drop-in for the older Whirlpool and Kenmore boxes most other listings ignore.
Where the modern W10124096 kits aim at newer model lines, the Supco SM5109 is an exact replacement for Whirlpool part 833697, and the feedback keeps pointing at older Kenmore units specifically. It is a metal-bodied motor rated 120 volts and 2 watts with a spin speed of 1550 rpm, and it is made in the USA. That 120-volt rating is the interesting contrast: the Blutoget W10124096 kit above runs 115 volts, so if your appliance label reads 120 volts, this is the closer match on paper.
Supco claims this part meets or exceeds OEM specifications, and owners generally back up the performance side. Replacement quality and value are the next two things that keep coming up in its favor, and owners also cite money saved against a service call. It weighs 1.9 pounds, which is heavier in the hand than the little W10124096 kits — a signal of the metal build rather than a fault.
Here is where the honest read matters. Noise and RPM sit as mixed feedback points on this motor — some owners find it quiet, and some find it a touch loud, with a few noting it runs slowly. That is not a defect report; it is a fit-strategy question. A 2-watt, 1550 rpm motor behaves differently from a 4.1-watt replacement, so if your fridge was designed around the higher-output unit, this one may not move the same air volume. Performance is what earns the most praise here by a clear margin, so the motor does its job — just be sure 120 volts and 2 watts match what came out of your fridge.
The fit story: a direct replacement for Whirlpool 833697, aimed squarely at Whirlpool and Kenmore units that newer kits leave out.
The catch: at 2 watts and 1550 rpm it is a lower-output motor than the 4.1-watt kits here, and noise and speed feedback runs mixed — a poor match if your original was the higher-wattage design.
Pick it when: the sticker on your old motor reads 833697 and your fridge label says 120 volts.
Pass if: your appliance was built around a 4.1-watt, 115-volt motor — the output levels are different enough to matter.
4. TOMOON W10124096 W10130108 W10204250 Condenser Fan Motor
One of the few listings that tells you exactly which fridges it cannot fix.
Most replacement-part listings only tell you what they fit. This one leads with a warning, and it is worth reading twice. The TOMOON kit is built for 115V, 4.1W (35.7mA) motors (115 volts, 4.1 watts, drawing 35.7 milliamps), and the listing states plainly that if your refrigerator uses a 78mA fan motor, this one will not function properly and may fail to start because of a load mismatch. That kind of honesty is rare enough in this category that it earns the pick a spot on the list — check your old motor’s current rating first and you will know in ten seconds whether to keep reading.
The kit itself is complete: 2-wire motor, durable ABS fan blade, wiring harness, and mounting screws. TOMOON claims high-grade metal construction with a precise aperture for a tight fit, rubber coils designed to resist cracking, and an ABS blade that improves air circulation and shortens the time the refrigeration system has to work. The cross-reference is broad, covering W10124096, W10204250, W10509333, W10861645, 2188727, 2188538, 2188728, 2188729, 2315538, AP4318657, and PS1957416, and it fits Whirlpool, Kenmore, KitchenAid, Maytag, and Estate units.
Tooling is basic: a socket set, a screwdriver, and pliers. TOMOON repeats the safety step — disconnect power and wear gloves. Owners describe the motor as working perfectly with a good fit, and the strongest value comment in the feedback says it saved a buyer from replacing the whole fridge. With 4.5+ stars across a modest set of reviews, it holds the same top score as the LinkEZ pick above. The narrower review base is the fair caveat: you are trusting a verified track record rather than a long one.
Why it stands out: the explicit 35.7mA versus 78mA warning is the single most useful piece of pre-purchase information in this whole category.
Where it is thinner: the review history is smaller than the LinkEZ or Whirlpool OEM picks, so the long-term picture rests on fewer data points.
This is your part if: your old motor is the 115V, 4.1W, 35.7mA design and you want a complete kit with an ABS blade included.
skip it if: the sticker on your failed motor shows a 78mA rating — the load mismatch is spelled out in the listing.
5. BlueStars 2188874 Refrigerator Condenser Fan Motor 4-Pin
Four pins instead of bare wires — the detail that decides most of these orders.
If your old Whirlpool motor plugs in with a 4-pin connector rather than loose wires, this is the one to look at. The BlueStars 2188874 is a 4-pin, 115-volt, 60Hz, 4.1-watt condenser motor that replaces 2188875, WP2188874, AP6006075, and PS11739140. BlueStars also gives you a clean rule for choosing between its own parts: if your original fan motor has 3 terminals, order part number W10204250 instead. That single sentence prevents a lot of wrong orders.
The fit list is deep. It names Kenmore models starting 106.5114 and 106.3224, Whirlpool models in the 7ET1FTKXRQ and 7GS2FHAXTA series, and Amana units in the A1RXNGFY and A2RXNMFW ranges. It also covers Whirlpool, KitchenAid, Maytag, Jenn-Air, Roper, Crosley, Estate, Inglis, Magic Chef, Dacor, and Thermador for top-name replacement. BlueStars says the part is made to OEM standards and fixes the two symptoms people actually notice: a fridge running too warm, and a noisy unit.
The most common real-world hitch is the wiring accessories. That is the one aspect where feedback turns negative, with buyers noting the necessary harness is not included with this motor. So plan for the fact that this is a motor, not a kit — if your harness is intact and reusable, that is fine, and if it is not, you will be sourcing it alongside. Functionality is what people praise most here, with replacement quality next. The honest counterweight: 4-pin designs are built for newer model lines, and older 3-terminal fridges should not be ordering this at all.
The reason to buy: a true 4-pin, 115-volt, 60Hz, 4.1W replacement with a deep Kenmore, Whirlpool, and Amana fit list.
The one snag: no wiring harness in the box, so a brittle original harness turns this into a two-part job.
Go here if: you have counted four pins on your old connector and your harness is still in usable shape.
Look at the TOMOON kit instead if: you want the harness and blade bundled in rather than reused.
6. Edgewater Parts W10124096 Condenser Fan Motor Kit
Half an hour with basic tools, and the fridge is blowing cold again.
The install-friendly pick of the group. Edgewater ships the motor, fan blade, wire harness, and screws together, and the feedback describes the job as a basic-tools half-hour rather than a service call. That matches the spec sheet: 1.7 amps, 120 volts, and a 1/8″ x 1-1/4″ shaft, which is the same shaft size the Blutoget kit uses. If your appliance label reads 120 volts rather than 115, this is the closer electrical match of the two full W10124096 kits on this list.
The cross-reference covers a long tail of numbers — 1378525, 2188538, 2188727, 2188728, 2188729, 2188732, 2188891, 2206005, 2315538, 2315558, AP4318657, W10124096, W10124096VP, W10130108, W10204250, W10509333, and W10861645. The fit is scoped to ED5, GS2, GS6, and MSD model families, so if your fridge starts with one of those prefixes, you are in range. Edgewater also states a refund-within-warranty promise with no questions asked, which takes the sting out of a fit mistake.
Installation is the aspect owners praise most here, and functionality is right behind it. The recurring story is a fridge made more efficient, quieter operation, and a perfect fit. Value comes up strongly too, with repair-cost savings that make a motor swap look obvious in hindsight. What to weigh: this is a 120-volt part, so a 115-volt system is a different match, and the ED5/GS2/GS6/MSD model scope means newer or unrelated model lines need a different cross-reference check before ordering.
What it does best
- Complete kit — motor, blade, harness, and screws, so no separate parts hunt
- Feedback centers on a straightforward install with basic tools
- 120-volt, 1.7-amp rating matches fridges labeled 120 volts
- Refund-within-warranty promise, no questions asked
Where it stops short
- Fit is scoped to ED5, GS2, GS6, and MSD model families
- It is a 120-volt part, not a 115-volt one
Best fit for: an ED5, GS2, GS6, or MSD fridge labeled 120 volts where you want the whole assembly in one box.
Not the one for: a 115-volt system, or a model outside those four families.
7. Whirlpool W10124096 Genuine OEM Condenser Fan Motor
The factory part, with the factory box, for the buyer who does not want to think about it twice.
This is the one Whirlpool builds itself. It arrives as a genuine OEM (Original Equipment Manufacturer) part, engineered to the exact original specification rather than reverse-engineered against it. The kit includes the fan motor, fan blade, wiring harness, hardware, and printed instructions, and the motor is rated 115 volts and 4.1 watts at 13.6 ounces. It replaces 2188538, 2188727, 2188728, 2188729, 2188732, 2188891, 2206005, 2315538, 2315558, W10124096VP, W10130108, W10204250, W10509333, and W10861645 — a cross-reference long enough to cover most of the family.
The track record here is the deepest on the list. Performance leads the feedback by a wide margin, with quality close behind and installation also cited repeatedly — owners typically describe a fridge running like new after about thirty minutes of work. Quiet operation and fit round out the picture, and the fact that it is an original part comes up as its own reason for choosing it. If you have ever returned a knock-off motor that spun wrong from the start, the appeal of the factory part is obvious.
The plain trade-off is cost. You are paying a clear premium over the equivalent aftermarket kits here, and functionally the aftermarket W10124096 kits are cross-referenced to the same part number. What that premium buys you is the certainty of the genuine article plus the printed instructions in the box, which the bare motors do not include. Note also that the rating is 4.5+ stars on a much larger base than most of this list — the score is not the very highest here, but it rests on far more real-world use than the smaller listings can show.
What the premium buys: the genuine Whirlpool part, blade, harness, hardware, and printed instructions in one factory package.
The balance point: the aftermarket W10124096 kits cost less and cross-reference the same number, but send no instructions and are not factory parts.
Choose it when: you want zero doubt that the part is the genuine Whirlpool item and want the included instructions in hand.
Lean toward the Blutoget kit if: the same part number shows on your old motor and you would rather not pay the factory premium.
Know the Specs
Voltage — 115V vs 120V
Voltage is the electrical pressure the motor is built to run on. In this group you will see both 115 volts and 120 volts, and while they look close, they belong to different designs. The Blutoget, TOMOON, BlueStars, and Whirlpool OEM motors run 115 volts; the Supco SM5109 and Edgewater kit run 120 volts. Match the number printed on your old motor’s label and you avoid a mismatch that can show up as a motor that will not start.
Wattage And Amp Draw
Wattage is the motor’s actual power output, and it is the number that tells you whether the replacement moves the same air as the original. The 4.1-watt motors here — Blutoget, TOMOON, BlueStars, and Whirlpool OEM — are the higher-output group. The Supco SM5109 is a 2-watt motor. The TOMOON listing adds the clearest warning in the category: a 115V, 4.1W (35.7mA) motor and a 78mA motor are not interchangeable, and the wrong one may fail to start.
Shaft Size And Connector Type
The shaft is the metal spindle the fan blade presses onto. Most of these motors use a 1/8″ x 1-1/4″ shaft, which is why the fan blades in the kits are interchangeable. The connector matters just as much: most here are 2-wire designs, but the BlueStars 2188874 is a 4-pin unit. If your original has 3 terminals, BlueStars tells you to order W10204250 instead. Count pins and wires before you order.
What Comes In The Box
A motor-only listing leaves you reusing the old fan blade, harness, and screws. A kit bundles them. The Blutoget, TOMOON, Edgewater, and Whirlpool OEM picks are full kits with blade, harness, and hardware; the LinkEZ, Supco, and BlueStars picks are motor-only. If your blade is cracked or your harness is brittle, the kit saves a second order and a second wait.
Common Questions
How do I know which Whirlpool refrigerator fan motor fits my fridge?
Can I use a 120-volt motor in place of a 115-volt one?
What does the 35.7mA versus 78mA warning mean on the TOMOON kit?
Do I need a 4-pin motor or a 2-wire motor?
How long does a condenser fan motor replacement take?
Should I buy a full kit or just the motor?
Is the genuine Whirlpool OEM motor better than the aftermarket kits?
What symptoms mean the condenser fan motor has failed?
Will a Whirlpool motor fit my Kenmore or Amana refrigerator?
The Bottom Line
For most Whirlpool refrigerator owners, the motor to buy is the LinkEZ W10128551. It covers the widest spread of models — 2500+ Whirlpool-family and 600+ Kenmore — and its reputation for simply keeping on running is the steadiest on the list. If your old motor is in the W10124096 family and you want the blade and harness in the box, the Blutoget W10124096 kit is the value call. And if your connector has four pins rather than bare wires, the BlueStars 2188874 is the one that fits. Before you order any of them, write down the three numbers on your old motor — part number, voltage, and current rating — because those three decide your fit, not the badge on the box.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of July 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.




