A spiral bolt extractor removes a broken or rounded bolt by gripping the inside of a pilot hole you drill first, then turning it counterclockwise with a wrench.
Shear a bolt head off flush and there’s nothing left to grab. The flutes on a spiral extractor bite into a drilled hole instead, and every turn digs them deeper. Get the pilot hole wrong and a five-minute job becomes a drilled-out threaded hole needing a helicoil.
This guide follows the procedure in order, using IRWIN HANSON tooling as reference since size and drill recommendation are etched on the tool. For sizing across a full kit, our tested spiral bolt extractor roundup covers which sets handle which fastener ranges.
Spiral Extractor vs. Bolt-Extractor Socket
A spiral screw extractor goes inside a drilled hole in a broken fastener. A bolt-extractor socket grips the outside of a rounded nut or bolt head. Different tools for different failures.
Rounded but attached head: use the socket type. Snapped-off stub or recessed fastener: use the spiral extractor. An extractor socket won’t grab a broken stud with no head to bite.
Both are hand tools with no software, subscription, or regional requirements. Compatibility comes down to correct sizing, not measurement system.
How To Use A Spiral Bolt Extractor: The Step Order
The sequence is fixed: assess, drill, seat, turn. Skipping the assessment is where most failures start.
- Secure the workpiece and clean the fastener. Clear debris, wear eye protection, and don’t use a cracked or damaged extractor.
- Assess the fastener. Identify diameter and whether it’s broken flush, recessed, rounded, corroded, or protruding. IRWIN HANSON etches extractor size and recommended drill size on the tool — read it before drilling.
- Apply penetrating oil on rusted or seized bolts and let it work. Skip near heat, sparks, or oxygen-sensitive processes.
- Center-punch the fastener. A clear center mark keeps the drill from wandering; off-center drilling damages surrounding threads.
- Drill a straight pilot hole at the specified drill size. A left-handed bit is recommended because it may start loosening the fastener as it cuts. Depth should let the flutes grip without bottoming out.
- Seat the extractor. Insert the spiral end, confirm engagement, and don’t force an oversized extractor into an undersized hole.
- Turn counterclockwise with a tap wrench, adjustable wrench, or the specified drive tool on the square end. Slow, steady torque lets the flutes bite.
- Stop if resistance spikes. Spiral extractors can snap, and a hardened broken extractor is very hard to drill out. Reassess hole size, depth, alignment, corrosion, and engagement instead of adding force.
- Remove the fastener and clean the threads. Inspect the hole, clear debris, and retire any extractor showing cracks, chipped flutes, or deformation.
When the bolt breaks free, torque drops and the extractor turns freely — back it out by hand.
Common Mistakes That Break Extractors
Most failures trace to four errors: wrong drill diameter, off-center hole, insufficient depth, or clockwise turning.
- Too shallow a hole — flutes never engage and just spin.
- Impact wrench on a hand-tool extractor — IRWIN specifies hand operation; impact torque snaps flutes.
- Continuing after the extractor twists or slips — that’s the warning before it cracks.
- No eye protection or unsecured workpiece — easiest to prevent, costliest to skip.
| IRWIN HANSON Model | Drill Bit Size | Best For |
|---|---|---|
| EX-4 / 53704 | 1/4 inch HSS | Broken studs, bolts, socket screws, fittings |
| EX-5 / 53705 | 19/64 inch HSS | Larger broken bolts and studs |
| 10-piece set | 5/64 – 19/64 inch | EX-1 through EX-5 sizes in one kit |
| 48-piece master set (3101010) | Varies by model | Six spiral extractors (52401–52406) plus thirteen bolt extractors (53901–53913) |
IRWIN’s spiral extractor and drill bit combo packs pair each extractor with its matched high-speed-steel bit, removing the guesswork. The 53704 spiral extractor and drill bit combo is typical, with size markings etched on both pieces.
Which Extractor Size First?
Match the extractor to the fastener’s minor diameter, not its head size. The pilot-hole drill is the real constraint — the extractor must fit snugly without forcing.
For a fastener under a quarter inch, start at the smallest extractor in the set. Step up only when the hole and extractor both confirm the larger size will seat. The IRWIN HANSON catalog lists tap-wrench, drill-size, and removal-range data by model number — the fastest way to confirm a match before drilling.
Replacement bits and extractors are the cheapest insurance. Keep a spare of your most-used size and you won’t be stuck mid-job.
Common Questions
Can A Spiral Extractor Remove A Bolt Broken Below The Surface?
Yes, that’s the case spiral extractors handle best. A recessed or flush-broken fastener has no head to grip, so you drill into the stub and let the flutes bite from the inside. The pilot hole must be centered and deep enough for the flutes to engage, or the extractor will spin without gripping.
What Happens If The Extractor Breaks Off Inside The Bolt?
The extractor is hardened steel, so drilling it out is difficult but not impossible with a carbide bit and patience. This is why the procedure calls for stopping the moment resistance spikes. Reassessing hole depth, alignment, and corrosion beats adding torque every time.
Do You Always Need A Left-Handed Drill Bit?
Not strictly, but it’s recommended. A left-handed bit spins opposite the fastener’s thread direction, so it can begin loosening the bolt during drilling itself. A standard right-handed bit still works — it just won’t give you that head start on a stubborn fastener.
Sources
- IRWIN Tools. “Spiral Extractor & Drill Bit – 537 Series – 53704” Product specifications for the EX-4 / 53704 combo pack.
- IRWIN Tools. “Spiral Extractor & Drill Bit – 537 Series – 53705” Product specifications for the EX-5 / 53705 combo pack with 19/64-inch bit.
- IRWIN HANSON. “Irwin Hanson Catalog” Model-by-model tap-wrench, drill-size, and removal-range reference data.