A swimming pool chlorinator uses electrolysis to turn dissolved salt into chlorine, which sanitizes the water before reverting back to salt to start the cycle again.
A saltwater pool still runs on chlorine; the difference is where that chlorine comes from. Instead of hauling jugs of liquid chlorine from the store, a chlorinator generates its own sanitizer from ordinary sodium chloride dissolved in the water. Hayward’s AquaRite manual specifies an ideal salt concentration of 2,700–3,400 ppm, with 3,200 ppm considered optimal.
The table below lays out what each part of the system does, from pump to controller, so you can see exactly where the chemistry happens.
What Happens Inside The Electrolytic Cell?
That chlorine sanitizes the water as it returns to the pool.
The disinfecting work depends on the form the chlorine takes. Lower pH favors hypochlorous acid, which is the more effective sanitizer; poor pH control wastes the chlorine the cell produces and can damage metal components. Hayward’s AquaRite manual also calls for 1.0–3.0 ppm free chlorine. Many cells reverse polarity periodically to reduce mineral scale buildup, and the manufacturers’ specs list a self-cleaning cell, built-in salt and temperature probes, and a flow switch.
| System Component | Core Job | Key Spec |
|---|---|---|
| Salt in pool water | Supplies the chloride the cell converts | 3,200 ppm ideal |
| Circulation pump | Moves water through filter and cell | Must maintain adequate flow |
| Electrolytic cell | Applies DC current to titanium plates | 600 g/day at 100% output |
| Controller | Regulates output and cell type | 0–100% adjustable |
| Flow switch | Stops the cell without water movement | Built into AquaRite cells |
| Cell life | Working lifespan of the plates | 12,000 hours |
| Free chlorine target | Sanitizer level in the pool | 1.0–3.0 ppm |
Where Does The Salt Go, And Why Size Matters?
Salt leaves the pool through water loss, not evaporation — backwashing, draining, and splashing carry it out, so it needs periodic replacement. Sizing the cell correctly matters just as much as the salt level.
Hayward’s current lineup shows how the ratings scale. The T-CELL-15 and AquaRite Pro AQR15-PRO both serve pools up to 40,000 gallons, while the T-CELL-9 tops out at 25,000 gallons. The TCELL940 and TCELL940-W are extended-life replacement cells for the same 40,000-gallon ceiling.
Those gallon figures are maximum-volume guidance, not a promise. Heavy bather loads, intense sun, high heat, and low stabilizer levels all push chlorine demand past what the cell was rated for. A shortlist of top-rated pool chlorinator systems helps narrow the field before you buy.
What Do Most Owners Get Wrong About Upkeep?
Treating a saltwater pool as chemical-free is the most common error; the generator produces chlorine, but it does not eliminate testing, balancing, or occasional shocking. Several other mistakes show up repeatedly.
- Wrong salt or too much of it.
- Ignoring pH. Off-target pH undercuts sanitizing power and attacks metal parts.
- Running the cell at low flow. Two-speed and variable-speed pumps running at low speed may not supply enough flow, and inadequate flow means inefficient chlorine production.
- Skipping bonding and grounding. Hayward identifies improper electrical installation as a cause of metal damage and corrosion.
- Assuming universal compatibility. Firmware, cell type, electrical requirements, and certifications differ by model and region.
Match chlorinator output to pump runtime, and adjust output whenever the runtime changes. The full setup sequence: confirm pool volume, pick a cell rated for it, dissolve the salt per the manufacturer’s chart, run circulation until it distributes, set the controller to the correct cell type, then test free chlorine, pH, alkalinity, and hardness on a regular schedule. One last check before you commit — Hayward’s AquaRite owner’s manual is the reference to confirm your specific model’s settings.
Common Questions
Does A Saltwater Pool Need Chlorine Added Manually?
Not for routine sanitation, because the cell generates chlorine continuously while the pump runs. Heavy use, hot weather, and contamination can outpace production, so a supplemental dose or shock is sometimes necessary to restore the free chlorine level to the 1.0–3.0 ppm range.
How Often Do You Add Salt To A Pool?
Salt only leaves through water loss, so there is no set schedule. Check the level after backwashing, draining, or a season of heavy splashing, and top up only when a test reads below the 2,700 ppm floor. Evaporation alone never removes salt.
What Happens If The Salt Level Gets Too High?
Excess salt can corrode decks, railings, and pool equipment. The fix is dilution: partially drain the pool and refill with fresh water, then retest before running the cell again. Never add salt without testing first, since the concentration only drops through water replacement.
Sources
- Hayward. “AquaRite Owner’s Manual.” Supports salt concentration, free chlorine targets, and cell operation details.
- Hayward. “TCELL940 Manual.” Supports replacement cell configuration requirements.
- Hayward. “Pool Salt Chlorine Generator Specification (CSI Type).” Supports chlorine production, cell life, and flow specifications.