Pick a snow kit by matching it to the tire size, axle, and clearance rules in your owner’s manual, then buy winter tires for steady snow or chains and approved traction devices for temporary grip.
Start at the tire placard on the driver-side door frame. A kit that clears the fender on one trim can chew a brake line on another.
Start With The Manual And Tire Placard, Not The Catalog
Your owner’s manual decides what you’re allowed to run: permitted device type, which axle, any maximum speed, and whether traction devices are prohibited outright.
Copy the full tire designation off the placard — width, aspect ratio, wheel diameter, load index, and speed rating. Buying by year, make, and model alone is how people end up with a set that rubs. Some vehicles are only approved for chains when that exact tire-and-rim combination is cleared by the manufacturer.
If the manual specifies “Class S” or any low-profile, cable, or textile category, buy only that category. A bulkier conventional chain isn’t a substitute — it’s what the restriction exists to prevent.
Winter Tires Or Chains? What Decides The Outcome
Winter tires win for recurring cold, snow, and ice; chains and approved traction devices are for temporary grip when roads turn bad.
NHTSA’s winter driving guidance says winter tires should match the size and construction type of your other tires and go on in pairs or all four wheels. Don’t mix winter and non-winter tires on the same car.
Chains belong on snow-covered or icy roads, not dry pavement. Leave them on bare asphalt and you’re grinding metal into your tires, your fenders, and the road.
All-wheel drive doesn’t mean chains on all four corners. Requirements vary by vehicle, and the manual — not the badge — names the axle.
The Numbers That Keep A Snow Kit From Damaging Your Car
Clearance, speed, and tread depth separate a working kit from an expensive repair.
Clearance must hold with the vehicle loaded as the manufacturer specifies. If a device touches the brake line, suspension, fender liner, or wheel, it doesn’t go on. NHTSA names 2/32 inch as the minimum tread depth reference — below that, traction devices treat a symptom while the tire fails the job.
Set tire pressure cold, using the manufacturer’s recommended value from the manual or door-frame label — not the maximum pressure molded into the sidewall.
Don’t air down to force a chain on. Instructions prohibit reducing tire pressure for installation or removal, and spinning a wheel fitted with chains is equally off-limits.
Check state and local rules before you travel; some jurisdictions require chains during storms, others restrict them once pavement clears.
What Goes In The Kit And How To Fit It
A complete kit is the correctly sized set of traction devices plus gear to install them safely at the roadside.
- Gloves, kneeling protection, and a flashlight or headlamp
- Reflective or high-visibility outer layer
- An emergency marker or warning device
- Jumper cables — NHTSA lists them among core winter supplies
Then work the sequence. Read the manual, read the traction-device maker’s fitment chart using the exact tire size, and test-fit on dry pavement. Inspect tires for damage and uneven wear. Install or remove on level ground with the car stationary and secured, wearing something visible.
After installation, drive a short distance, stop, and check centering and tension. One manufacturer caps chain-equipped driving at 30 mph (50 km/h) — a ceiling, not a target.
Before every season, inspect used chains for broken or damaged components, then clean and dry them after use and store away from chemicals that attack the links. If you’d rather compare ready-made bundles, this roundup of the best snow kits for cars covers tested options by vehicle type.
For full cold-weather guidance, NHTSA’s winter driving tips cover tires, supplies, and pre-trip checks.
Sources
- National Highway Traffic Safety Administration. “Winter Driving Tips” Covers winter tires, emergency supplies, and cold-weather vehicle preparation.
- National Highway Traffic Safety Administration. “Winter Driving Tips 2021–2022” Supports tread depth, tire pressure, and emergency kit recommendations.
Common Questions
Can I put chains on just the front tires of an all-wheel-drive car?
Only if your owner’s manual says so. All-wheel-drive systems vary widely; some manufacturers specify a single axle, others require a matched set on all four wheels. Installing on the wrong axle can strain the drivetrain or trigger traction-control faults. The manual overrides any general rule you read online.
How fast can I drive with traction devices installed?
Follow the lower of the two limits — your vehicle manufacturer’s and the traction-device maker’s. One common manufacturer specification caps chain-equipped driving at 30 mph (50 km/h), but that figure isn’t universal. Many devices are rated for considerably less, and exceeding the limit risks device failure and body damage.
Do I need to remove chains once I reach clear pavement?
Yes. Traction devices are built for snow-covered and icy roads; running them on dry asphalt damages the chains, the tires, and potentially the vehicle. Pull over at a safe spot as soon as the road clears, remove them on level ground, and store them clean and dry.