9 Best Smoke Hollow Grill Parts | Fit Your Smoker, Not a Guess

Disclosure: This post contains affiliate links. As an Amazon Associate I earn from qualifying purchases, at no extra cost to you. Learn more

Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.

Replacing a worn grate or a rusted heat plate on a Smoke Hollow grill is usually a five-minute job — the hard part is ordering the right part. One wrong digit in a model number and you get a grate that rocks in the frame or a heat tent that sits too high. So the picks below are grouped by the exact part they replace, with the model lists spelled out so you can check yours before you click.

This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.

Every part here physically fits Smoke Hollow grills, and the reviews show which replacements owners rate as sturdier than the factory part. This breakdown covers the best Smoke Hollow Grill Parts by part type, model fit, and material so you reorder once and get back to cooking.

Top Picks

PS9900 Grill Grates Replacement Parts for Smoke Hollow PS9500
Best OverallPS9900 Grill Grates4.5+★250+ ratingsTwo cast-iron halves that drop into the PS9900 frame and hold heat like the original never did. This is the pack to buy if your cooking surface is the worn-out piece.Check price on Amazon
16.5' Heat Plate Replacement Parts for Smoke Hollow PS9500 PS9900 6800
Best Value16.5″ Heat Plate4.5+★The quiet worker under your grates — a shield that keeps dripping grease off the burner tubes. Heat plates are the part most people forget until the flame starts licking up around a burger.Check price on Amazon
SST18L Heat Plates Replacement for Smoke Hollow Grill, Stainless Steel
Rust-Resistant PickSST18L Heat Plates4.0+★80+ ratingsA stainless heat tent for the SST18L crowd, sized at 16 by 6 by 3 inches and ready to slot in. If your grill plate carries an SST18L code, this is the direct swap.Check price on Amazon

How To Choose The Best Smoke Hollow Grill Parts

The single biggest reason a replacement part comes back is a model mismatch — not a bad part. Smoke Hollow sold the same basic cabinet under a long list of model codes, and the grates, heat tents, and burners changed between them. So start with the plate, not the product photo.

Read the rating plate before you read the listing

Open the cabinet door or look at the back panel of your grill and find the sticker with the model number. Write it down exactly. Then read the listing’s fit list and check that your code appears in it, character for character. A PS9900 and a PS9900-SY18 can share a grate, but a 6500 and a 7000CGS may not.

Measure the old part, not the space it sat in

Pull the worn grate or heat plate out and lay a tape across it. A grate listed at 16 1/2 inches by 10 9/10 inches per piece only fits a firebox built for that footprint. Measuring the part itself takes thirty seconds and settles the question faster than any fit chart.

Match the material to how you cook

Cast iron holds heat and gives you dark sear marks, but it needs a light oil coat to stay non-stick. Stainless steel heat plates shrug off rust and wipe clean with soapy water. Porcelain steel sits in the middle — the coating protects the steel underneath, so it needs a gentler hand with a scraper.

Buy the whole worn assembly at once

If your heat plates are rusted through, your burners are probably scorched too. Kits that bundle heat tents, burners, and a crossover tube save you a second order and a second wait. Check what is actually in the box before you assume one pack covers a three-burner grill.

Side-by-Side Comparison

Model Best For Part Type Material Listed Fit Amazon
PS9900 Grill Grates (2-pack)★ Best Overall Replacing worn cooking grates Cooking grate, 2 pieces Enamel cast iron PS9900, PS9500, 6800, 8500, 7000CGS Amazon
16.5″ Heat Plate (PS9500/PS9900)Best Value Shielding burners from grease drips Heat plate Porcelain steel PS9500, PS9900, 6800, 6500, SH9916, SH5000 Amazon
SST18L Heat PlateRust-Resistant Pick Single-plate SST18L swaps Heat plate, 1 piece Stainless steel SST18L, SST18L-3, SST18L-4, SST18L-6, SH19030819 Amazon
SST18L-6 Heat Plate SH19030819 series heat tents Heat plate, 1 pack Stainless steel SST18L, SST18L-6, SH19030819, MB20030819 Amazon
Gas Burner BURNER205 Restoring a dead burner tube Burner Stainless steel Masterbuilt and Smoke Hollow 205, FM205 Amazon
47183T-21 Charcoal Tray Charcoal-pan replacement Charcoal tray Alloy steel PS9900, PS9500, 6500, 6800, 8500, SH5000, SH7000, HC4518L Amazon
Hisencn 16.5″ Cast Iron Grates Cast-iron sear marks Cooking grate, 2 pieces Cast iron PS9900, 7000CGS, 8500, PS9500, 6800 Amazon
TC3718 Burner & Heat Tent Kit Rebuilding a 3-burner top end Heat tents, burners, igniter, crossover tubes Stainless steel CMB37181, SH19033319, TC3718, TC3718SB Amazon
47183T Grease Tray Assembly Replacing a rusted drip pan Drip tray + catch pan Stainless steel PS9900, 47183T-30, TR028, 47180T, 7000CGS, PS9500, 1800CGS, 8500 Amazon

Detailed Reviews

★ Best Overall

1. PS9900 Grill Grates

Our pick — 4.5+★ from 250+ verified ratings; the strongest balance of quality and price.

Enamel Cast IronTwo-Piece Set

Two cast-iron halves that drop into the PS9900 frame and hold heat like the original never did.

This is the pack to buy if your cooking surface is the worn-out piece. You get two grates, each measuring 10 7/10 inches by 16 1/2 inches, and together they span 21 2/5 inches by 16 1/2 inches across the firebox. That two-piece split matters in daily use: you can lift one half to add wood chips or check a burner without pulling the whole cooking surface off a hot grill.

The material is enamel-coated cast iron, and the coating is the reason it survives. It resists rust and corrosion, holds up against chipping and cracking, and spreads heat evenly across the bars instead of leaving hot bands over each burner. In practice that means a row of burgers browns at the same rate front to back. A light oil coat before the first cook gives you a non-stick surface, and the listing suggests repeating it to keep that going.

Where this grate pulls ahead is heat retention — cast iron soaks up heat and gives it back, which is what draws dark sear marks rather than pale grill lines. The fit list is unusually long for a replacement part: Smoke Hollow PS9900, PS9900-SY18, PS9500, 7000CGS, 8500, and 6800, plus Kenmore, Charbroil, Expert, and Outdoor Gourmet models spelled out individually. What wins people over is quality — that is the thing reviewers circle back to most, with fit close behind. It carries 4.5+ stars across 250+ ratings, the highest of the grate picks.

Why it earns the top slot

  • Cast iron holds heat and delivers real sear marks, not just grill lines
  • Two separate halves make mid-cook access easy
  • Long published fit list covers a wide spread of Smoke Hollow, Kenmore, and Charbroil models
  • Enamel coating resists rust, chipping, and cracking

What to weigh first

  • Cast iron needs a light oil coat and hand washing to stay non-stick
  • Heavier than a bare steel grate, so lifting a half takes a little more grip

Go for this if: your PS9900, PS9500, or 6800 needs a full cooking-surface swap and you want cast-iron sear.

Think twice if: you want a wipe-and-go surface — stainless sheds grease with less fuss.

Best Value

2. 16.5″ Heat Plate

Porcelain SteelGrease Shield

The quiet worker under your grates — a shield that keeps dripping grease off the burner tubes.

Heat plates are the part most people forget until the flame starts licking up around a burger. This one sits between the burner and the grate, where it stops food from touching open flame and catches the fat that would otherwise clog the burner ports. The result is fewer flare-ups and a burner that keeps an even flame through the season.

It measures 16 1/2 inches by 3 15/16 inches and is built from porcelain steel — steel with a glass-like coating fired onto it. That coating is why soapy water is enough to bring it back to clean. For fit, the listing covers Smoke Hollow PS9500, PS9900, 6800, 6500, SH9916, and SH5000 gas grills, so check your code against that list before ordering.

Here is the honest limit: this is a single plate, so a multi-burner grill needs more than one. If you are replacing all the heat shields in a five-burner cabinet, count how many slots you have and order accordingly. The porcelain coating also does not like a metal scraper digging at it. Treat it like a mug and it will last.

The everyday win: grease goes down, not onto the burners, so your flame stays blue and your grates stop getting sooted up.

The sizing catch: at 16 1/2 inches by 3 15/16 inches it fits one slot — measure your old plate and multiply by the number of burners you are covering.

Reach for this if: you are replacing one rusted heat tent on a PS9500, PS9900, or 6500 and want the lowest-fuss material.

Look elsewhere if: your whole set of plates is shot — you will want a multi-pack or the full kit below.

Rust-Resistant Pick

3. SST18L Heat Plates

Stainless SteelOne-Piece Plate

A stainless heat tent for the SST18L crowd, sized at 16 by 6 by 3 inches and ready to slot in.

If your grill plate carries an SST18L code, this is the direct swap. It fits SST18L, SST18L-3, SST18L-4, and SST18L-6, and it also lists a run of SH1903 models including SH19032319, SH19032419, SH19032519, SH19032619, SH19032719, SH19032819, SH19032919, SH19033019, and SH19030819.

Stainless is the reason to pick it over a coated plate: the metal itself resists rust, so there is no porcelain layer to chip off and expose bare steel. The plate spreads heat across the cooking surface and cuts the flare-ups that come from fat hitting open flame. At 2.09 pounds it is light enough to lift out one-handed for a scrub.

Here is where the numbers get interesting. Set this plate beside the SST18L-6 replacement further down and the listings look odd — this one is called out at 16 x 6 x 3 inches while the other lists at 2 x 2 x 2 inches. Both are described as fitting the same SH19030819 family. That tells you the spec field on these listings is not always the real footprint, so measure your old plate and trust your tape over the numbers on the page.

Fit is the thing reviewers praise most on this listing, and the quality read follows close behind — buyers report the stainless plate feels sturdier than the thin steel it replaces. What to watch: a small number of these arrive with a slight warp at the edge, so check the plate sits flat before you cook on it.

What it brings to the grill

  • Stainless steel body resists rust with no coating to chip
  • Fits the SST18L family plus nine SH1903 model codes
  • 2.09 pounds — light enough to lift out for cleaning
  • Even heat spread cuts flare-ups from dripping fat

Before you order

  • Published dimensions conflict with the sister SST18L-6 listing, so measure your old plate
  • Ships as a single plate, not a set

Fits the bill for: SST18L and SH19030819 owners who want stainless without a coating to worry about.

Hold off if: you need a batch of plates for the whole firebox — this is one piece per pack.

Compact Pick

4. SST18L-6 Grill Heat Plate

Stainless SteelMasterbuilt Cross-Fit

A heavier stainless heat tent for the SH19030819 series that also crosses over to Masterbuilt.

The piece that separates this one from the SST18L plate above is the extra cross-fit: it lists replacement duty for Masterbuilt MB20030819 parts as well as the Smoke Hollow SST18L, SST18L-3, SST18L-4, and SST18L-6 models. If you own a grill that carries both brand names on the badge, that overlap is worth having.

The plate is heavy-duty stainless steel and weighs 1.98 pounds, and it weighs 1.98 pounds — a shade lighter than the 2.09-pound SST18L plate. Both act as a heat shield and flavorizer bar, sitting over the burner to catch drips and spread heat. Same job, same slot, different badge on the box.

The fit list runs SH19030819, SH19032719, SH19032319, SH19032419, SH19032519, SH19032619, SH19032819, SH19032919, and SH19033019. Note the published product dimensions read as 2 x 2 x 2 inches, which cannot be the true footprint of a heat plate that shields a burner. Use the model list, not that figure, and confirm against your old part before you buy.

The cross-fit advantage: one part number covers Stainless Smoke Hollow SST18L variants and Masterbuilt MB20030819 — handy if your grill’s badge is ambiguous.

The real-world caveat: the dimension field on the listing is clearly a placeholder, so the model number list is the only reliable sizing guide here.

Worth grabbing if: your grill’s plate is stamped SST18L-6 or MB20030819 and you want stainless.

Skip the guesswork by: measuring your old tent — the listed dimensions will not help you here.

Burner Fix

5. 205 BURNER205 Gas Burner

Stainless Burner18-Inch Tube

When one burner tube is scorched out and the rest of the grill is fine, this is the single part that fixes it.

This is a replacement burner for the Masterbuilt or Smoke Hollow 205 and FM205 grill and stove, sold under the BURNER205 part number. It measures 18 inches by 7 1/2 inches, which is the span that has to line up with the mounting holes and the gas valve on your unit. Stainless steel is the finish and the frame material, so the tube resists the heat cycling that eats through cheaper steel burners.

This burner is listed at 18 x 1 x 7.5 inches. Both it and the 47183T-21 charcoal tray down the list are Smoke Hollow parts, but they serve completely different jobs — one feeds gas, the other holds coals.

The catch is specificity. This is a single-burner part built for the 205 and FM205, so it is not a universal tube that drops into a PS9900 or a 6800. If your grill’s model plate says anything other than 205 or FM205, this is not your burner. Buy it when you already know the tube in your hand matches.

This is your part if: your 205 or FM205 has a dead burner and the rest of the cabinet is sound.

Keep looking if: your model code is not 205 or FM205 — this tube will not line up.

Charcoal Swap

6. 47183T-21 PS9900 Charcoal Tray

Alloy SteelRust-Treated

The pan that holds your coals and takes the worst of the heat, rebuilt in solid treated steel.

Charcoal trays live a brutal life — direct coals on one side, drippings on the other. This one is made of solid alloy steel with a phosphatized surface, a chemical treatment applied to slow rust, and the alloy steel pan is thicker and heavier than a stamped tray. It is a single pack and the care instructions call for soapy water hand washing.

The fit list is the important part on a tray: Smoke Hollow 47183T, 47183T-21, 47183T-21-R, plus PS9900, PS9500, 6500, 6800, 8500, SH5000, SH7000, SH9916, HC4518L, SH19030119, and SH19030219. The non-porous, glossy surface means ash and grease wipe out rather than soaking in.

Fit and quality both draw strong marks here, and the function reads as intended — it holds coals and drops in where the original sat. Durability is the honest grey area: the maker claims a rust-slowing treatment, but some owners find it rusts faster than they hoped over a season of uncovered storage. Keep the grill covered and empty the ash after each cook, and this is a fair trade for the price of a replacement tray.

Where it delivers

  • Solid alloy steel, described as thicker and heavier than standard trays
  • Phosphatized surface aimed at slowing rust
  • Wide fit list across PS9900, PS9500, 6800, 8500, SH5000, and SH7000
  • Glossy non-porous surface wipes clean with soapy water

The honest trade-off

  • Rust resistance is a mixed report — uncovered storage speeds it up
  • Hand wash only, no dishwasher shortcut

Best for: restoring a charcoal-burning Smoke Hollow with a rotted-out original pan.

Plan for: a grill cover and regular ash dumps — that is what keeps the treated steel from going the way of the old tray.

Top Performer

7. Hisencn 16.5″ Cast Iron Grill Grates

Heavy Duty Cast IronTwo-Grate Set

A non-magnetic cast-iron pair that sears hard and covers a wide spread of 24-inch grills.

Hisencn builds these from non-magnetic heavy-duty cast iron, which is a marker of denser iron rather than the recycled scrap some budget grates use. Each grate measures 16 1/2 inches by 10 9/10 inches, and as a set of two they cover 16 1/2 inches by 21 8/10 inches. That total footprint is the whole cooking surface on the PS9900 and 7000CGS, plus the 8500, PS9500, and 6800.

Compare it to the cast-iron grate pick at the top of this list: that pack lists each half at 16 1/2 inches by 10.7 inches, while these list at 16 1/2 inches by 10 9/10 inches. Close, but read your old grate with a tape before you assume the two brands swap freely.

What the iron does for you is hold heat and give it back slowly. The bars cook to temperature and stay there, so a steak hits the metal and gets a real crust instead of a steam. The surface is also shaped to drain fat away from the food, which keeps flare-ups down. Fit is what wins people over here, with quality a close second, and buyers put the ease of cleaning and the value on top of that. The one spec that looks off is the 1-pound item weight — a two-piece cast-iron set is not a 1-pound package, so treat that figure as a listing slip.

The sear factor: dense non-magnetic cast iron soaks heat and delivers the dark crust that thin steel grates cannot.

Worth knowing: cast iron rewards a light oil rub and hand washing, and the listed total footprint (16 1/2 by 21 8/10 inches) only fits a firebox built for it.

Pick these if: your PS9900, 7000CGS, or 24-inch Smoke Hollow needs a full surface and you want maximum sear.

Consider the alternative if: you would rather not deal with cast-iron upkeep — stainless is easier to live with.

Most Complete Kit

8. TC3718-25 TC3718-26 TC3718-27 Grill Replacement Parts

3-Burner RebuildIgniter Included

One box that covers the whole top end of a tired three-burner Smoke Hollow.

Most replacement orders fix one part. This one fixes the assembly. In the box you get three stainless heat tents, two grill burners, one stainless burner with an ignition wire and igniter electrode, and two stainless crossover tubes — the piece that carries flame from burner to burner so all three light together.

That combination is what makes it the efficient buy when a grill has sat through several winters. Heat plates rust out, burners scorch, and the crossover tubes clog, all in the same stretch of time. Buying them together saves a second order and a second wait. The stainless is described as solid rather than a thin sheet wrapped around ordinary steel, and the stainless parts are built to hold heat and spread it evenly across the grates.

Fit is narrow and specific — TC3718-25, TC3718-26, TC3718-27 original part numbers, plus CMB37181, SH19033319, TC3718, and TC3718SB grills. At 3.08 pounds it is the heaviest single part in this article, which tracks with a multi-piece kit. The catch is that a three-burner kit on the wrong model is money wasted, so match your model code first. The shiny, non-porous surfaces wipe clean easily once it is installed.

What is in the box

  • Three stainless heat tents plus two burners and a third burner with igniter
  • Two stainless crossover tubes included — no separate order needed
  • Solid stainless construction, not wrapped steel
  • 3.08 pounds of parts, the most substantial kit here

Before you commit

  • Fits only TC3718-family and CMB37181 / SH19033319 / TC3718SB grills
  • Higher cost than a single part, so only worth it if several pieces are worn

The right call when: your TC3718SB or CMB37181 has multiple scorched parts and you want them all in one delivery.

Scale back if: only one heat plate is rusted — a single plate covers that job for far less.

Cleanest Fix

9. 47183T PS9900 Grease Tray

Stainless Drip TrayCatch Pan Assembly

A stainless drip tray and catch pan that puts an end to grease pooling in the bottom of the cabinet.

A rusted-through drip pan is one of the least glamorous failures on a gas grill, and one of the messiest. This kit is a stainless tray plus a stainless catch pan with a custom grease cup that attaches underneath to collect what drains off. Emptying and rinsing that cup is far easier than hauling out the whole tray.

The solid stainless build is described as heavier than the wrapped-steel versions, and stainless steel holds up to the heat and grease a drip tray collects. Replacing a rusted or missing tray also cuts the flare-ups caused by grease sitting in the cabinet and keeps the unit looking right. The fit list covers Smoke Hollow PS9900, 47183T-30, TR028, 47180T, 7000CGS, 47183T, PS9500, 1800CGS, and 8500.

This is the least notable part in the list and the one most likely to save you a real headache. The catch is that it is a two-piece assembly — tray plus catch pan — so confirm your model takes both pieces rather than a tray alone. Surface finish is glossy and non-porous, which means a soapy wipe handles most of it.

Order this if: your PS9900, 7000CGS, or 8500 has a drip pan that leaks or has rusted out.

Double-check first: that your grill uses the tray-and-catch-pan setup — some cabinets take a tray only.

Know the Specs

Part type — the real decision

Before material or size, you are choosing a job: a cooking grate is the surface food touches, a heat plate shields the burner, a burner feeds gas, a charcoal tray holds coals, and a drip pan catches fat. Buying the wrong part type is the most common ordering error, because the photos look similar. Confirm what slot the worn piece came out of before you compare anything else.

Material — cast iron vs stainless vs porcelain steel

Cast iron holds heat and sears hard but wants a light oil coat and hand washing. Stainless resists rust with no coating to chip. Porcelain steel pairs a steel core with a glass-like coating that wipes clean but dislikes a metal scraper. Each choice trades maintenance against durability, and none is wrong — it depends on how much upkeep you will actually do.

Model fit — read the code, not the badge

Smoke Hollow grills share a cabinet across many model codes, and the internals changed between them. A part listed for PS9900, PS9500, and 6800 may not fit a 6500. Read the rating plate on your cabinet and match each character to the fit list. When the listed dimensions and the fit list disagree, the fit list and your own tape measure win.

Size and weight — what actually matters

Measure the old part with a tape, not the space it sat in. A grate listed per-piece at 16 1/2 by 10 9/10 inches only fits a firebox built for that footprint. Weight hints at density: a dense cast-iron grate holds heat longer, while a lighter stainless plate is easier to lift out for a scrub. Ignore listing weights that clearly contradict the part — a two-piece cast-iron set is not 1 pound.

Common Questions

How do I find my Smoke Hollow grill model number?
Look for a rating plate on the cabinet door, the back panel, or under the side shelf. It carries the model code, and sometimes a serial and a part number. Write the code down exactly, then match it against the fit list on the listing before you order anything.
Will a PS9900 grate fit my PS9500 grill?
The two-piece enamel cast-iron grate here lists Smoke Hollow PS9900, PS9900-SY18, PS9500, 7000CGS, 8500, and 6800 in its fit list, so yes, that grate is published as fitting the PS9500. Always verify your own code appears in the list, because model variants within the same family can differ internally.
Is cast iron better than stainless steel for replacement grates?
Neither wins outright. Cast iron holds heat and gives you a darker sear, but it needs a light oil coat and hand washing. Stainless resists rust with no coating to chip and wipes clean more easily. Choose cast iron for searing and stainless for low-maintenance upkeep.
How often should heat plates be replaced on a Smoke Hollow?
Replace them when you see rust through the plate, warping, or flare-ups that keep coming back after cleaning. There is no fixed schedule — it depends on how often you cook and whether the grill is stored covered. A plate that has lost its coating and shows bare rusted steel is ready to swap.
Can I use a replacement grates set on a different grill brand?
Only if the listing says so. The cast-iron grates here also list Charbroil Hybrid Quickset, Kenmore, Kingsford, Expert Grill, Outdoor Gourmet, Royal Gourmet, and certain 24-inch Walmart charcoal grills. Fit is governed by the size and the published model list, not by the brand badge.
Do I need to replace both grates or just the worn one?
The two-piece sets are sold as a pair, so a worn half usually comes with a fresh half. That keeps the cooking surface level and heat even across the whole firebox. If only one half is damaged and you buy a single-plate part, check the size matches the half you are replacing.
What is the difference between a heat plate and a heat tent?
The terms describe the same job in different shapes. A heat plate is a flatter shield over the burner, while a heat tent is angled like a peaked roof to shed drips. Both sit between the burner and the grate, and both keep grease off the flame. Either shape works if the fit and size match your grill.
Can I replace just the burner without replacing the heat plates?
Yes, as long as the heat plates still do their job. The BURNER205 tube is sold as a single burner for the 205 and FM205, and it fits the existing mounting points. If the plates are also rusted through, a kit that bundles burners and heat tents saves a second order.
How do I measure a heat plate before ordering a replacement?
Pull the old plate out and lay a tape across its length and its width at the widest points. Note those two numbers and compare them to the listing. When the listing’s dimension field looks unrealistic, like 2 x 2 x 2 inches for a full heat plate, trust the fit list and your own measurement instead.
Will a stainless drip tray stop my grill from flaring up?
It helps by catching the grease before it pools in the cabinet. Flare-ups come from fat hitting the flame or sitting in a rusted tray, so replacing a leaking drip pan removes one source. Keep the tray and catch cup emptied to get the most from it.

The Bottom Line

For most owners fixing a Smoke Hollow, the smoke hollow grill parts set that earns its place is the PS9900 enamel cast-iron grate pair — it holds heat, sears hard, and its published fit list reaches across PS9900, PS9500, 6800, 8500, and 7000CGS. If your cooking surface is fine and the burner underneath is not, grab the BURNER205 gas burner for the 205 and FM205. And when several parts have gone at once on a three-burner cabinet, the TC3718 kit puts heat tents, burners, igniter, and crossover tubes in one box. Match your model code to the fit list, measure the old part with a tape, and a five-minute repair is all this ever needs to be.

One last nudge: the cast-iron grate pair rates highest of the group at 4.5+ stars across 250+ owners, so if you are unsure where your worn part sits, start there and check the code.

How we choose

We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.

Sources

Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.

As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.

Scroll to Top