A thread plug gauge is a fixed-limit inspection tool that passes or fails an internal thread using a GO member that must enter and a NO-GO member that must not.
A tapped hole that looks perfect can still fail its mating bolt, and the thread plug gauge catches that before assembly. It gives a verdict, not a dial reading: the hole either accepts the GO end and refuses the NO-GO end, or it is rejected.
What Does Each End of the Gauge Check?
The GO member verifies the thread’s functional minimum condition; the NO-GO member verifies the pitch diameter has not grown past its permitted maximum.
The GO end is a full-form member checking minimum major diameter, minimum pitch diameter, thread flanks, and leads together — asking whether a correctly made mating screw would fit. Notably, it does not check the minor diameter. If that matters, use a separate plain plug gauge, pin gauge, or bore gauge.
The NO-GO end targets the maximum pitch-diameter condition alone, and its outside diameter may be smaller than the GO member’s for that reason. It also isn’t built to reach the deepest portions of a long thread.
How Do You Run the Test Step by Step?
Match the gauge to the thread first, then test GO before NO-GO, turning both by hand with no forcing.
- Confirm the gauge matches the part. Thread system, nominal diameter, pitch, tolerance class, and standard must all line up. A Unified inch thread follows ASME B1.2; a metric gauge reads something like M12 × 1.25, class 6H.
- Clean the hole. Clear chips, burrs, dirt, and cutting fluid. Wipe the gauge too, and work at roughly 20 °C.
- Turn the GO member in by hand. It should enter fully, or to the specified full thread depth, freely. If it won’t start or stalls, the thread is undersized, damaged, contaminated, or formed wrong.
- Try the NO-GO member. It should not enter beyond the allowance your standard specifies — a practical field rule is no more than two turns.
- Decide. GO enters and NO-GO stays within allowance means the hole passes. A NO-GO member that screws in too far means the pitch diameter is oversized, and the part is rejected.
Run the same order every time. Reversing it hides a failing thread behind a good-looking first result.
What Standards and Configurations Apply?
ASME B1.2, Gages and Gaging for Unified Inch Screw Threads, sets dimensions and requirements for gauges used on UN, UNR, and UNJ thread forms and describes their purposes and use.
Gauges come in three shapes: separate GO and NO-GO plugs (two tools), and combined limit plug gauges carrying both members on one handle, the version most shops keep on the bench. Metric gauges are labeled by diameter, pitch, and class — e.g., M12-1.25-6H-GPNP. JIS Grade 2 gauges follow a similar pattern with models such as M3-0.5-GP2WP2 and M10-P1.5-GP2WP2.
| Gauge Element | What It Verifies | Pass Condition |
|---|---|---|
| GO member | Functional minimum: major diameter, pitch diameter, flanks, leads | Enters fully by hand, freely |
| NO-GO member | Maximum pitch diameter only | Does not enter past the standard’s allowance |
| Minor diameter | Not checked by a thread plug gauge | Requires a plain plug, pin, or bore gauge |
| Very short threads | Turn-count rules get unreliable | Follow the applicable standard, not the two-turn habit |
| Dirty or wet holes | Contamination skews engagement | Clean and dry before testing |
Picking a gauge set for a working shop? These tested thread plug gauge picks cover common sizes and classes. For official gauge dimensions and tolerance tables, the ASME B1.2 standard for Unified inch screw thread gauges is the reference.
Which Mistakes Cause False Rejections?
Most bad readings come from forcing the gauge, testing a dirty part, or reading “NO-GO” as “must not enter at all.”
- Reading NO-GO too strictly. The allowance may permit limited engagement, depending on thread standard, gauge type, material, and thread length.
- Leaning on the handle. Inspection is a hand operation; torque and excess force damage threads and gauge alike.
- Using the wrong gauge. A mismatched thread form, pitch, tolerance class, or standard will reject good parts all day.
- Ignoring temperature. Metal moves with heat; roughly 20 °C is the reference point.
- Expecting a measurement. This is a fixed-limit check. For an actual pitch-diameter number, use a thread-measuring instrument.
Follow the GO-then-NO-GO order, keep the part clean, and trust the verdict.
Common Questions
Does a thread plug gauge measure the thread size?
No. It is a fixed-limit tool delivering pass or fail, not a numeric reading. For actual pitch diameter, use a thread-measuring instrument or bore gauge. The plug gauge tells you whether the hole conforms to its specified standard and tolerance class.
Why does the GO member go in but the NO-GO also enters?
That means the pitch diameter has grown past its permitted maximum while the thread still meets minimum conditions — the hole is oversized. It will accept a mating screw, but the fit will be loose and the part should be rejected. Check that the gauge matches the pitch and tolerance class before you scrap the part.
Can I use one gauge for inch and metric threads?
No. Unified inch and ISO metric threads use different thread forms, pitches, and tolerance classes, and their gauges are not interchangeable. A metric gauge such as M12 × 1.25, class 6H will not correctly verify a Unified inch thread. Match the gauge to the thread system and standard before testing.
Sources
- ASME. “B1.2 – Gages and Gaging for Unified Inch Screw Threads” Defines gauge dimensions and requirements for UN, UNR, and UNJ thread forms.
- GSGage. “Thread Plugs” Source for gauge configurations, metric class labeling, and listed specifications.
- BAER Tools. “Thread Gauges” Background on thread gauge types and thread standard references.