How to Measure for a Range Hood Scoop? | Measure the Cooktop

Measure your range’s cooking surface at its widest left-to-right point and front-to-back edge, then pick a hood at least that wide—ideally about 6 inches wider.

A tape measure held against your old hood tells you what you already own, not what actually fits—the cooking surface itself sets the real numbers. Get the width, depth, and vertical clearance right, and a scooped hood captures smoke and grease from every burner instead of letting half of it drift past.

How Wide Should a Range Hood Be?

The hood should be at least as wide as your range or cooktop, and a hood about 6 inches wider is the better choice when the cabinets allow it. Measure the range from its leftmost cooking edge to its rightmost cooking edge—not the body panel, the actual burner layout.

Common hood widths are 24, 30, and 36 inches, but do not assume that 30-inch label is exact. Whirlpool notes that hoods sharing a nominal width can differ in real width, depth, duct outlet, and mounting requirements, so verify the actual dimensions on the spec sheet.

  • Coverage rule: the hood must reach over both the front and rear burners.
  • Wall space check: measure between adjacent cabinets at the narrowest point before buying.
  • Under-cabinet fit: the hood should match the width of the cabinets above the range.

What Depth and Clearance Do You Need?

Measure cooking depth from the front cooking edge to the rear edge, skipping the control panel and decorative trim.

Vertical clearance runs from the cooktop surface to the planned underside of the hood.

Cooking Surface Typical Clearance Range Watch For
Electric cooktop 20–24 inches Manufacturer may differ
Gas cooktop 24–30 inches Higher heat, more flux
Under-cabinet hood 24–30 inches Cabinet height limits it
Downdraft hood Odd behind range Sits at exactly range width
Open-top broiler 24 inches to combustibles Hood must span full unit
Duct, up to 400 CFM 4-inch minimum Check outlet location
Duct, 550–1,200 CFM 6-inch or larger Routed outdoors

Clearance is a starting point, not a rule you can bank on. Whirlpool and every appliance manual can specify a different permitted height for a listed model, and local building officials can impose stricter requirements, so read both the hood and range manuals before cutting cabinets.

Where Do People Measure Wrong?

The most common mistake is measuring the existing hood, which locks in whatever odd sizing the previous owner installed. Let the cooktop guide the purchase.

Other stumbles worth avoiding:

  • Including the range’s control panel in the depth figure, which inflates coverage.
  • Buying a hood narrower than the appliance, a sure way to lose front-burner capture.
  • Confusing hood body height with chimney height when planning overhead space.
  • Skipping the duct route—a 550 CFM or higher hood needs 6-inch ducting, not the 4-inch line that suits 400 CFM units.
  • Assuming ductless operation is allowed without checking the product listing and local code.

Once you have the numbers on paper, a tested scoop-for-hood roundup narrows the field fast, since you’re comparing real widths and depths instead of marketing labels.

The code allows listed ductless hoods only when installed per manufacturer instructions and when other mechanical or natural ventilation is present—a detail worth confirming in the ICC’s exhaust systems chapter before purchase.

Common Questions

Can I put a wider hood over a smaller range?

Yes. A hood roughly 6 inches wider than the cooking surface is acceptable and often preferred, provided cabinet and wall space allow it. Just keep the hood centered over the cooktop so both front and rear burners stay covered.

Does gas really need more clearance than electric?

Usually, yes. Common guidance calls for 20 to 24 inches above electric and 24 to 30 inches above gas. The manufacturer’s manual for your specific model always overrides the general range, so check both documents.

What if my duct is too small for the hood?

A hood rated above 400 CFM typically needs 6-inch or larger ducting. If your existing ductwork is 4-inch, either choose a lower-CFM model or plan to upgrade the duct before installing a stronger hood.

Sources

Scroll to Top