What Is a Wall Mount Ethernet Switch and How Does It Work?

A wall mount Ethernet switch is a standard network switch built with mounting holes so you can screw it to a wall, connecting wired devices on one local network while staying safely off the floor.

The label describes the hardware, not the network. Inside, the switch forwards Ethernet frames between its RJ45 ports using learned MAC addresses — exactly what a desktop switch does. What changes is the install: a small box tucked onto a wall near your gear instead of a loose box collecting dust under a desk.

The sections below cover how it moves data, what to check before you buy, and the mounting steps TP-Link documents for its wall-mountable models.

How Does A Wall Mount Ethernet Switch Move Data?

The switch silently learns which MAC address lives on which port, then sends each unicast frame only toward the destination port rather than blasting it everywhere.

Plug computers, access points, cameras, printers, VoIP phones, and an upstream router into the RJ45 ports. The switch auto-negotiates link speed and duplex per port, so a 1-gigabit device and a 100-megabit device on the same switch each settle at their own best rate. TP-Link’s installation guide for its Gigabit Easy Smart PoE+ line lists 10, 100, and 1,000 Mbps support with Auto-Negotiation and Auto MDI/MDIX, which means you don’t need crossover cables.

Unmanaged models run with zero setup. Smart and managed versions add VLANs, QoS, monitoring, link aggregation, and security controls — the exact list depends on model and firmware.

One thing a switch does not do: replace your router. Internet access, IP addressing, firewalling, and routing between networks stay on the router. The switch only expands the wired side of your local network.

What Should You Check Before Buying One?

Match three specs to your situation — port count and speed, PoE budget if you’re powering cameras or access points, and mounting-hole spacing — because a great switch with the wrong spacing won’t fit your pre-drilled spot.

  • Ports and capacity: count every wired device plus the uplink to your router. A five-port switch with four devices and one uplink is full.
  • PoE: if you’re powering devices over the cable, confirm the switch’s standard (802.3af or 802.3at), the device’s power class, and the total watt budget. A PoE switch can fail to power an incompatible or over-budget device.
  • Mounting-hole spacing: this varies widely.
  • Cable: copper Ethernet runs max out at 100 m; TP-Link specifies Category 5e or better for 1000BASE-T.

Those TP-Link numbers are model-specific reference points, not a universal standard. Pull the exact spacing from your own model’s installation guide before you drill.

If you’d rather skip the spec-hunting, this roundup of tested wall mount Ethernet switches compares real models side by side.

Model Ports And PoE Budget Mounting Hole Spacing
TL-SG105PE 5 × 1 Gbps; 65 W PoE 39 mm
TL-SG105MPE 5 × 1 Gbps; 120 W PoE 39 mm
TL-SG108PE 8 × 1 Gbps; 64 W PoE 94 mm
TL-SG1210MPE 10 × 1 Gbps + 1 SFP; 123 W PoE 150 mm

How Do You Mount It On A Wall Correctly?

Mark two holes at your switch’s exact spacing, drive two screws leaving a small gap between head and wall, and hang the switch — then confirm it sits upright with ports facing down where your model specifies it.

TP-Link’s wall mounting guide outlines the sequence:

  1. Confirm your exact model is listed as wall-mountable and note its mounting-hole spacing.
  2. Mark two wall points at that same spacing.
  3. Install two suitable screws (usually not included) — use proper anchors for drywall or masonry.
  4. Leave enough screw-head-to-wall clearance for the switch to engage the holes.
  5. Hang the switch on the screws.

Orientation matters more than people expect. Mount it upright, not sideways. For the TL-SF1008P, TL-SF1008LP, TL-SF1009P, and TL-SG1008P, TP-Link specifies ports facing downward and LEDs facing upward. Sideways mounting can block ventilation, strain the cables, or hide the status lights you need to read.

Leave breathing room between the switch and the wall, and don’t stack devices on top of each other. And don’t assume “wall-mountable” means outdoor-rated or safe inside a wall cavity — most aren’t.

Common Questions

Does A Wall Mount Switch Work The Same As A Desktop Switch?

Yes. The networking hardware is identical — same MAC learning, same frame forwarding, same speed negotiation. The only difference is the enclosure’s mounting holes. A wall-mountable model simply gives you the option to secure it off the floor, which helps in utility closets, garages, or anywhere cabling runs along a wall.

Can A Wall Mount Switch Power Cameras And Access Points?

Only if it’s a PoE model and the powered device matches. Check the switch’s PoE standard (802.3af or 802.3at), the device’s required voltage and power class, and the switch’s total watt budget. Connecting incompatible or over-budget equipment can cause power loss or failure, so verify those specs against the datasheet before buying.

Do I Still Need A Router If I Add A Switch?

Yes. A switch expands wired ports on your local network but doesn’t hand out IP addresses, provide internet access, or firewall traffic. Those jobs belong to the router. Typical setup: router connects to the switch’s uplink port, and all wired devices connect to the switch.

Sources

Scroll to Top