A string trimmer rack fits when its holder opening, latch depth, and bracket spacing clear your trimmer’s shaft, guard, handle, and battery or fuel tank — and no rack is universal, so measure your tool before you buy.
Buy the rack by the numbers on your trimmer, not by the engine size or the cutting swath. A rack that swallows a 26cc straight-shaft trimmer will not always clear a curved-shaft model with a bulky loop handle and a 4-pound battery hanging off the back. The fit comes down to four measurements and a trailer rail.
Which Measurements Decide Whether A Rack Fits?
Four measurements decide the fit: the largest shaft or housing diameter at the support point, the width and depth of the guard and handle, the total length, and the mounting surface’s hole pattern and clearance. Get those on paper and the rack spec sheet tells you yes or no in under a minute.
- Measure the trimmer’s largest shaft or housing diameter where the rack will grip it.
- Measure the guard, loop handle, battery, fuel tank, and control housing — every part that could hit the rack.
- Measure total length and note whether the tool hangs by its shaft, its handle, or a cradle.
- Compare those figures against the rack’s opening and published depth.
- Confirm the mounting surface, hole pattern, and rail or vehicle clearance.
- Load the trimmer, secure the cutting head, and shake it — the tool must not rotate, slide, or touch nearby equipment.
What Do Real Rack Specs Look Like?
Published rack dimensions vary widely, and the labels are not standardized. Two common racks show the range: a two-position trailer rack around 34 inches tall, and a three-position rack around 40 inches tall and 31 pounds. Read every spec sheet with the orientation in mind.
| Rack | Published Numbers | Best For |
|---|---|---|
| Buyers Products LT19 (2-position) | 33.75 in high; 1/8 in carbon steel; 1.5 in latch depth; 12.29 lb; slotted pre-drilled holes | Open landscape trailers and pickup beds with variable-height side rails |
| Green Touch XB103 Xtreme Pro (3-position) | 40.13 in high × 3 in wide × 10 in deep; 31 lb; aluminum mounting blocks | Commercial crews hauling three trimmers on open or closed trailers |
The Buyers LT19 lists at $127.00 with a $99.00 sale price, and the XB103 shows a $439.99 list with a $309.99 sale price on its retailer page — both are retailer-specific and move with promotions. Neither rack includes trimmers.
Where Do Buyers Get The Sizing Wrong?
The most common mistake is trusting the word “universal” instead of measuring the actual trimmer. The second is confusing capacity — how many tools fit — with the weight each position can safely hold. Those are two different limits, and only one of them appears in the marketing copy.
- Assuming a “commercial makes and models” claim proves fit without checking your own tool.
- Ignoring the guard, loop handle, battery, or fuel tank when checking clearance.
- Hanging a rack on drywall or weak framing without confirming the anchor and structural requirements.
- Mixing up height, width, and depth across product pages that label them inconsistently.
- Ordering the wrong part number — the Buyers listing advises matching LT19 to the equipment or replacement part before buying.
Foam-lined hooks cut scratching, noise, and vibration, but they do not replace a proper lock or tie-down. Use the latch and a strap, then confirm the head cannot swing into the trailer wall or a neighboring machine. If you would rather compare tested options side by side, this roundup of string trimmer racks breaks down what holds up on a real trailer.
Does The Mounting Surface Change The Answer?
Yes — the same rack can fit one trailer and fail another because of rail height and hole spacing. The Buyers LT19 mounts by bolting to an open trailer through slotted, pre-drilled holes meant to align with variable-height side rails. Measure your rail height and bolt spacing before you commit.
Wall-mounted hangers add a second check: the anchor has to reach solid framing or blocking, not just drywall. Walk the trimmer past the rack before you drill anything.
Common Questions
Can One Rack Hold A Straight-Shaft And A Curved-Shaft Trimmer?
Sometimes, but not automatically. A curved-shaft trimmer often sits at a different angle and carries a larger loop handle, so the rack’s opening and latch depth may clear one tool and bind the other. Measure both trimmers before assuming one rack serves the whole fleet.
How Much Weight Can Each Rack Position Hold?
Manufacturers rarely publish a per-position weight limit, and a two- or three-tool capacity does not reveal it. Treat capacity as a count, not a load rating, and check the rack’s hardware and trailer mounting for the real limit. When in doubt, add a tie-down strap.
Do Foam-Covered Hooks Make A Rack Fit Better?
No — foam covers change comfort and wear, not fit. They reduce scratching, noise, and shock where the trimmer contacts the rack, but the opening, depth, and bracket spacing still have to match your tool. A pad cannot fix a hook that is too shallow or too wide.
Sources
- Buyers Products (via ECTTS). “Buyers Products LT19 2-Position Trimmer Rack” Source for LT19 dimensions, latch depth, mounting holes, weight, and pricing.
- Green Touch Industries (via Target). “XB103 Xtreme Pro Series 3-Position Line Trimmer Rack” Source for XB103 capacity, dimensions, weight, hardware, and pricing.