How to Choose the Right Trailer Tire Size and Load Rating? | Match the Label First

A trailer tire is the right one when its size, load range, and cold pressure match the trailer’s certification label or owner’s manual — not the wheel diameter.

A label that reads ST225/75R15 at 65 psi tells you nearly everything: the tire type, the physical size, and the pressure that makes its capacity count. Buy anything else and the axle is only guessing. The good news is that the whole decision collapses into four numbers pulled off one sticker — size, construction, load range, and recommended cold inflation — plus a quick check that the tires on each axle can carry their share of the loaded trailer.

Here is the order that works, the arithmetic that has to clear, and the mistakes that put trailers on the shoulder.

Where Do You Find the Trailer’s Required Tire Specs?

The tire size, tire type, load range, axle ratings, and recommended cold pressure are printed on the trailer’s certification label, and repeated in the owner’s manual. NHTSA’s towing guidance is direct on this: buy the size, type, and load range shown on that certification label or in the manual rather than matching whatever is currently bolted on.

Write down all of it before you shop: tire size, tire type (ST for a Special Trailer tire), recommended cold pressure, GAWR for each axle, and GVWR for the whole trailer. GAWR is the most weight that axle is rated to carry; GVWR is the ceiling for the fully loaded trailer. Those two numbers are the real target, because a tire is only correct if its capacity at the specified pressure covers them.

A size like ST225/75R15 unpacks clearly: ST means Special Trailer, 225 is the nominal section width in millimeters, 75 is the aspect ratio (sidewall height as a percentage of width), R is radial construction, and 15 is the rim diameter in inches. Federal tire-selection rules require the vehicle placard to list a tire size and recommended cold inflation pressure appropriate to the axle ratings, which is why the label outranks any guess based on what fits the wheel.

How Do You Confirm a Tire Carries the Axle’s Load?

Add the maximum load rating of the tires on one axle at the specified pressure, and that sum must meet or exceed that axle’s GAWR. The federal standard in 49 CFR §571.110 puts it plainly: the combined tire load ratings on an axle cannot be less than the axle’s rating.

A tandem-axle trailer carrying two tires per axle is a simple multiplication, but the loaded weight is where people slip. Include cargo, water and holding tanks, accessories, and how tongue weight shifts load onto the axles. Never exceed the trailer GVWR, any axle GAWR, the wheel rating, or the hitch rating — a stronger tire raises none of those ceilings. Putting a higher-capacity tire on a trailer does not increase its GVWR or GAWR; it only adds margin.

Load range letters (B through E in this size class) mark standardized capacity categories at given inflation conditions, and they are not a simple ply count. Take the required load range from the label or manual, then confirm the actual capacity in the tire maker’s load/inflation table rather than estimating from the letter. One manufacturer’s published figures for ST225/75R15 show the spread: 2,150 lb at 50 psi, 2,380 lb at 60 psi, 2,620 lb at 70 psi, 2,720 lb at 75 psi, and 2,830 lb at 80 psi, with the 80-psi maximum marked Load Range E and an 87-mph maximum speed rating. Verify the exact model before you buy.

Load/Inflation Reference for ST225/75R15 Tires

The table below shows why the letter alone can’t be trusted: capacity climbs with pressure, and the same size covers a wide range. Always confirm against your tire’s own published table and never exceed the maximum cold pressure molded on the sidewall.

Cold Pressure Published Load Capacity Notes
25 psi 1,430 lb Lowest figure in one maker’s table
50 psi 2,150 lb Common Load Range C point
60 psi 2,380 lb Above mid-range
65 psi 2,540 lb Load Range D in one table
70 psi 2,620 lb Near top of range
75 psi 2,720 lb Second-highest step
80 psi 2,830 lb Load Range E; 87-mph rating

Whether you are replacing a pair or upgrading all four, a roundup of tested trailer tires 225 75r15 with rim lets you compare actual load ranges and speed ratings side by side.

What Else Can Disqualify a Otherwise Correct Tire?

Size, load range, and pressure are necessary, not sufficient. The wheel, the clearances, and the rating of the components around the tire all have to agree. Before changing size, confirm rim diameter, rim width, bolt pattern, wheel load rating, tire-to-fender clearance, suspension clearance, and overall diameter.

Passenger-car tires are a specific trap. Under the same federal standard, passenger-car tire capacity must be divided by 1.10 when calculating trailer axle capacity, so an automotive tire of “equal” rating is not equal at all. Where the trailer specifies ST tires, use them.

Fit matching size, construction, load range, and inflation requirements across each axle, and avoid mixing substantially different tires on one axle. Check pressure cold before every trip with a calibrated gauge, and do not bleed off the rise that comes with driving. Inspect for cuts, bulges, uneven wear, cracking, and embedded objects, and replace damaged or worn tires regardless of remaining tread.

By the time you pick up a tire, the four numbers from the label should already decide it — and that label, not the dealer’s suggestion, is what settles the size, the load range, and the cold pressure you set before pulling out.

Common Questions

Can I upsize to a larger load range for more safety margin?

Usually yes, as long as the tire meets the trailer’s specified size and pressure requirements and you do not exceed the wheel’s load rating or the clearance limits. The higher load range adds margin but does not raise the trailer’s GVWR or axle GAWR, so the axle rating still governs how much you can carry.

Do I inflate to the pressure molded on the tire sidewall?

No. The sidewall figure is the tire’s maximum cold pressure, not the trailer manufacturer’s recommended setting. Inflate to the pressure on the trailer’s certification label using a calibrated gauge. Underinflation cuts load capacity and builds heat, while going over the sidewall maximum is unsafe.

Why do I check trailer tire pressure before every trip?

Tires start cold and warm up as they roll, but you set pressure cold so the load rating holds. Bleeding off hot pressure leaves the tire underinflated once it cools. A quick cold check with a calibrated gauge catches slow leaks, uneven axle loads, and the heat-related pressure rises that signal a problem.

Sources

Scroll to Top