A Wisconsin engine’s model, specification, and serial numbers sit on the blower housing plate, and those three numbers decide which parts fit.
Two Wisconsin engines can look identical and still take different carburetors, crankshafts, or ignition parts. Identifying your model and finding the right parts comes down to one habit: copying the stamped numbers off the blower housing instead of guessing from the sheet metal. The plate carries a model, specification, and serial number, and a parts counter needs all three for anything past a spark plug.
Photograph the plate first, then write out every character, letters, suffixes, and leading zeroes included.
Identifying Your Wisconsin Engine Model: Where The Plate Lives
The identification plate is screwed or riveted to the blower housing, the flywheel shroud, or the cooling-fin cover — the flat metal shield that wraps the cylinder fins.
Each number does a different job. The model points to the engine family. The specification number narrows it to the exact build, and special parts such as crankshafts often cannot be matched without it.
Model suffixes are not noise. A trailing D means the engine left the factory with a stellite exhaust valve and seat, so TH and THD are otherwise the same designation, as are BKN and BKND. The Wisconsin engine identification reference walks through the same plate locations and markings.
Horsepower, cylinder count, and shroud shape will not tell you what fits. Two 4-cylinder Wisconsin engines from different families share nothing that matters at the parts counter.
What If The Identification Plate Is Missing?
Count the cylinders, then read the numbers cast or stamped into the visible components — Wisconsin casting figures are frequently the part numbers too.
Three prefixes do most of the sorting. Crankcase numbers begin with BA, connecting-rod numbers with DA, and cylinder-head numbers with AB. Work outward from the crankcase, carburetor, and magneto before touching a wrench, then confirm the result against published model tables.
Repainted shrouds hide more plates than missing plates do.
Skip the teardown if you can. Wisconsin Motors Canada notes that its older-specification compilation is not guaranteed accurate, so treat any table as a starting point.
Matching Specs, Parts, And Safety Checks
Quote parts by model and specification number together, then confirm fuel type, starting hardware, and shaft configuration before money changes hands.
Published Wisconsin figures sort the families quickly:
| Wisconsin Model | Cylinders And Bore × Stroke | Rated Output |
|---|---|---|
| AENLD | 1 cylinder, 3.0 × 3.25 in | 9.2 hp at 3,600 rpm, 1957 |
| TJD | 2 cylinders, 3.25 × 3.0 in | 18.2 hp at 3,600 rpm, 1968–2001 |
| THD | 2 cylinders, 863 cc | 16.8 hp in old tables, 18.2 hp now |
| VH4D | 4 cylinders, 3.25 × 3.25 in | 30.0 hp at 2,800 rpm, 1956 |
| V465D | V-4 overhead valve, 177 cu in | 65.9 hp at 3,000 rpm |
| W4-1770 | 4 cylinders, 3.25 × 3.25 in | 35.0 hp at 3,000 rpm |
| W2-1230 | V-2, 1,230 cc | 25 hp at 3,600 rpm, to 1986 |
The table gets you to a family, not a part number. Fuel system is the next fork: THD engines ship as gasoline, LPG, or natural-gas units, and the same listing specifies 12-volt electric start with a 30-amp charging system. Ordering a gasoline carburetor for a propane engine wastes a week. When you’re ready to price common wear items, our tested Wisconsin engine parts roundup covers what holds up in service.
Repair specifications belong to the individual model.
Shut the engine down, let it cool, and disconnect the battery lead before pulling a shroud or fuel line.
Work in this order before you buy:
- Photograph the plate and transcribe all three numbers.
- Check the parts listing for a serial break.
- Confirm fuel type and starting system.
- Compare the model against published tables.
- Quote with model, specification, and serial together.
Common Questions
Is The Model Number Enough To Order Parts?
Usually for common items, but not always. Crankshafts and other special components can require the specification number, and a part can change at a stated serial break. Send the seller all three numbers in one message and ask them to confirm fit against their listing before the order ships.
What Does The Letter D Mean On A Wisconsin Model?
A trailing D marks a stellite exhaust valve and seat installation. The rest of the designation is unchanged, so TH and THD are otherwise equivalent engines, as are BKN and BKND. Parts listed for the plain model often fit, but confirm the specification number first.
Can The Equipment Maker’s Number Identify The Engine?
No. The equipment model identifies the machine, not the engine bolted to it, and the same tractor or generator often shipped with more than one Wisconsin engine over its production run. Check the engine plate first, then fall back to cylinder count and crankcase or carburetor numbers.
Sources
- Wisconsin Motors Canada. “Wisconsin Engine Identification” Covers identification plate locations and the model, specification, and serial number fields.
- Wisconsin Motors Canada. “Wisconsin Engine Specifications — Current Models” Source for displacement, horsepower, fuel options, and model-specific repair specifications.