Match the trailer’s certification label first, then confirm each axle’s tire capacity meets its GAWR at the listed cold pressure.
A tire that fits the wheel and looks right can still be the wrong tire. Trailers get loaded heavier than their owners expect, and the number that actually limits an axle — its gross axle weight rating, or GAWR — sits on a sticker most people never read.
That sticker on the trailer’s front roadside frame settles most of the argument over how to choose the right trailer tire size and load rating. It lists the original size, load range, and cold inflation pressure. What follows is reading it correctly, plus the one calculation it doesn’t do for you.
Trailer Tire Size And Load Rating: Where The Numbers Live
The certification label controls the decision, and it outranks the tire sidewall, a chart online, and anyone behind a parts counter. Federal tire rules treat the vehicle manufacturer’s specification as the reference point for any replacement.
Find it on the frame’s front roadside area, near the tongue, or on the serial-number plate. Four items matter: GVWR, the GAWR for each axle, the original tire size with its load range, and the recommended cold inflation pressure.
Then decode the sidewall. Trailer tires read left to right, and the ST prefix is a promise about service, not a size — ST tires belong on trailers, never on the tow vehicle.
| Sidewall Marking | What It Tells You |
|---|---|
| ST | Special Trailer construction, built for trailer service only |
| 225 | Section width in millimeters |
| 75 | Sidewall height as a percentage of section width |
| R | Radial construction |
| 15 | Wheel diameter in inches |
| Load range letter | Capacity class, not a pound rating — verify the marked max load |
| Max load at X psi | The tire’s ceiling at that pressure, measured cold |
| Speed rating | Top sustained speed the tire is rated to carry |
What Do Load Range Letters Actually Tell You?
Load range is a capacity class, not a pound figure. The letter historically tracked ply construction, yet actual capacity depends on tire size, inflation pressure, and application — so compare the marked maximum load at the specified pressure, never the letter alone. A Load Range D in one size and a Load Range D in another are different tires.
One comparison decides the whole purchase, and it’s the principle NHTSA’s tire selection and load limits guidance is built around: the tires fitted to an axle must carry at least that axle’s GAWR. Divide the axle’s loaded weight by the number of tires on it to see what each one carries, then confirm their combined maximum ratings meet or exceed the axle’s rating. Use loaded weight — trailer, cargo, water, accessories, and how the load sits. Unloaded weight tells you nothing.
Higher ratings don’t raise the trailer’s limits. GAWR, GVWR, hubs, brakes, wheels, and suspension stay where they were, and the lowest-rated component on the axle sets the ceiling. A Load Range E tire on a Load Range C axle buys weight and stiffness, not capacity.
Those are illustrations, not recommendations — your label and the tire maker’s current load table decide.
Speed rating counts too. Load, inflation, temperature, and speed interact, and running past the rating or chronically underinflated can end in a blowout.
Fit, Pressure, And The Mistakes That Fail Tires
Physical fit comes after the numbers. Confirm wheel diameter and width, bolt pattern, offset, fender and suspension clearance, and a valve stem rated for the pressure you’ll run. A correctly rated tire can still rub a fender on the first dip in the road.
Set pressure cold, to the trailer manufacturer’s specification rather than the number printed on the sidewall. Readings climb as tires heat on the road, and the rating already accounts for that. Check the rim too — it may permit less pressure than the tire does. Never bleed a hot tire down to the cold number.
Passenger-car tires and unapproved light-truck tires don’t belong on a trailer. Inflating to sidewall maximum because it feels safer is a mistake, not insurance. So is replacing one tire with a substantially different size or capacity, or nursing a cut, bulge, or separated tread.
If the sizing is settled and you’re ready to buy, this trailer tire replacement roundup narrows specific models by size and load range.
The order that works: read the certification label, decode the sidewall, do the per-axle math, match load range and cold pressure, then verify wheel and clearance fit. The tire is one link in a chain, and the weakest component on that axle is what your trailer can legally and safely carry.
Common Questions
Can I Use A Higher Load Range Tire Than The Label Shows?
Usually yes, if the size, wheel, and speed rating match and the tire is rated for the pressure you run. It will not raise your GAWR, GVWR, or axle rating, though. Over-sizing adds margin and stiffness, not legal capacity. Confirm rim and clearance limits first, and never use the extra headroom as permission to load the trailer heavier.
Why Do Trailer Tires Fail So Often?
Underinflation and heat cause most failures. A tire run below its specified cold pressure flexes more, builds heat, and can shed tread or blow out. Overloading, uneven cargo that shifts weight onto one axle, aged rubber, and road hazards add to the risk. Check pressure cold before each trip and inspect for bulges, cracks, and cuts.
Should I Match The Sidewall Pressure Or The Label?
Use the trailer manufacturer’s cold pressure from the certification label. The sidewall figure is the tire’s maximum at full load, not a recommendation for your trailer. Your actual axle weight may need less, and your rim may permit less. Set it cold, before driving, and never bleed a hot tire down to the cold number.
Sources
- National Highway Traffic Safety Administration. Tire Safety — Selection, Load, and Inflation Guidance Sets the vehicle manufacturer’s specification as the reference for replacement tires.
- National Highway Traffic Safety Administration. Tire Selection and Care Brochure Source for sidewall marking definitions, load range meaning, and cold pressure practice.
- National Highway Traffic Safety Administration. Tire and Axle Load Rating Reference Supports the per-axle capacity math and the lowest-rated-component rule.