Measure the clear inside width and height of the receiver-tube opening, then match that number to a cover’s stated receiver size.
A hitch cover one size too large slides straight out of the tube—almost always because a tape measure was laid across the outside of the receiver instead of the opening.
What Do The Four Receiver Sizes Actually Mean?
Receiver sizes run 1¼, 2, 2½, and rarely 3 inches—each number describes the opening’s inside width, not the hitch’s exterior.
Two sizes do most of the work. The 1¼-inch receiver usually appears on Class I and Class II hitches on passenger cars and smaller SUVs. The 2-inch receiver is common on Class III and Class IV hitches found on pickups, larger SUVs, and some full-size sedans. A 2½-inch tube belongs to heavy-duty setups; 3-inch receivers exist but stay rare.
Here is where buyers get burned: class and receiver size are related, not interchangeable, and towing capacity has nothing to do with which cover fits. Some Class II hitches use a 2-inch opening, so guessing from the class label alone can produce the wrong cover even when the label is right.
The Measurement Steps That Get It Right
Park the vehicle, let the hitch cool if used, and pull off any existing cover, ball mount, or adapter along with dirt and rust around the mouth of the tube. Clean metal measures honest. Then:
- Measure the clear inside width, inner wall to inner wall, across the square opening.
- Measure the clear inside height the same way. On a standard square receiver the two numbers match.
- Round to the nominal size: about 1¼, 2, 2½, or 3 inches.
- Check the product listing’s stated receiver size, mounting method, and whether a pin, clip, lock, or gasket comes included.
If both numbers land within about 1/16 inch of 2 inches, you have a 2-inch receiver. eTrailer’s fit guidance agrees: measure the receiver’s inside dimension, full stop.
| Receiver Opening | Typical Hitch Class | Where It Shows Up |
|---|---|---|
| 1¼ × 1¼ in | Class I–II | Passenger cars, small SUVs |
| 2 × 2 in | Class III–IV | Pickups, SUVs, full-size sedans |
| 2½ × 2½ in | Heavy-duty | Trucks, large towing setups |
| 3 × 3 in | Rare heavy-duty | Specialty and commercial rigs |
| 1¼ × 1¼ in (uncommon) | Class II | Occasional 2-inch-opening cases |
| 2 × 2 in (uncommon) | Class II | Verify by measurement, not badge |
| 2½ × 2½ in (uncommon) | Class IV | Verify the tube, not the towing rating |
Why The Cover’s Face And The Opening Are Different Numbers
What matters is what inserts into the tube, not the decorative face. Ordering from the face measurement gets you a cover that will not seat.
Mounting style matters too. CURT’s steel and plastic covers sit on a short shank held by a hitch pin and clip. Rubber covers, like part 22282 for a 2 × 2-inch receiver or part C22277 for the 2½-inch tube, press into place by friction with no pin. Part 2211 covers a 1¼-inch receiver, and part 22279 fits a 2 × 2-inch receiver with an integrated mounting loop. For a side-by-side of tested options, this roundup of trailer hitch covers pairs each style with its receiver size.
Hitch hardware confirms the pattern: CURT part 12264 is a Class II hitch with a 1¼-inch receiver that accepts standard 1¼-inch shanks, and part 14082 is a Class IV hitch with a 2-inch receiver built for 2-inch shanks. The receiver tube sets the size every time.
What current listings do not publish is reliable retail pricing—check the live product page before buying rather than trusting a remembered figure.
Which Mistakes Cause A Return?
Measure the outside of the receiver, measure the cover face, or trust the hitch class alone, and the box goes back.
- Keep the tape inside the opening, against the inner walls.
- Do not confuse a 2½-inch tube with a 2-inch one; that half inch blocks the fit outright.
- If an adapter or reducer is installed, measure the opening the cover will actually enter.
- For pin-mounted covers, check pin-hole alignment and confirm hardware is included.
- Skip friction-fit rubber on a loose, bent, or badly rusted receiver—it cannot grip what is not round.
One more habit: a hitch cover protects and decorates but is not a towing part. Pull it off before sliding in a ball mount, bike rack, or cargo carrier, and make sure it never blocks the pin hole, safety-chain points, license plate, lights, sensors, or exhaust.
Common Questions
Can I measure the hitch receiver without removing the ball mount?
No—the ball mount fills the opening and hides the inner walls the tape needs to touch. Remove it first, along with any cover, adapter, or built-up grime, then measure wall to wall.
Is the receiver size the same as the hitch’s towing class?
Not reliably. A Class II hitch can come with a 2-inch opening—uncommon but real—so a class badge alone can send you to the wrong cover. The tube’s clear inside measurement is the only figure that decides fit.
Does a 2½-inch cover fit a 2-inch receiver?
No. A rubber cover built for a 2½ × 2½-inch tube needs that size of opening to hold by friction; on a 2-inch receiver it sits loose and works its way out. Buy the cover matched to your measured size.
Sources
- CURT Manufacturing. “Tube Covers.” Source for cover materials, mounting styles, and receiver-size offerings.
- eTrailer. “How to Measure a Trailer Hitch Receiver Size.” Confirms that receiver fit is measured by inside dimension.
- Lippert. “CURT Rubber Trailer Hitch Cover, Fits 2-Inch Receiver, 22279.” Lists dimensions and weight for CURT part 22279.