A GoPro attaches to a selfie stick through its mounting fingers, a compatible buckle, or a standard 1/4-20 tripod thread, depending on the model.
The screw that holds your camera to a pole is the only thing between a $400 action cam and the pavement. Mounting a GoPro on a selfie stick comes down to matching the camera’s connection to the stick’s connection, then tightening things so nothing rotates mid-shot. GoPro’s own guidance is blunt about this: the mount is what makes a GoPro a GoPro, and a loose or mismatched one is the most common reason footage turns out shaky or a camera takes a tumble.
Here’s what actually matters — the three connection types, which cameras use which, how to set the angle, and the mistakes that cost people their gear.
Which Connection Type Does Your GoPro Use?
Most GoPros use the traditional two-finger mounting system, while newer models add a 1/4-20 tripod thread or GoPro’s Magnetic Latch Mount. Check your camera before buying a stick, because the answer decides whether you need an adapter at all.
The mounting fingers are the folding tabs on the camera’s base that slot into a buckle or case. This is the classic GoPro interface and it works with standard GoPro buckles and accessories across generations. If your stick has a folding buckle on top, you’re already compatible.
The 1/4-20 thread is the standard tripod screw found on cameras, monopods, and most selfie sticks. GoPro identifies the HERO12 Black as having built-in 1/4-20 threads, so it screws directly onto a threaded stick with no adapter. For any other GoPro, GoPro’s Tripod Adapters are designed to attach any GoPro to a tripod, monopod, selfie stick, or accessory using a standard 1/4-20 mount.
The Magnetic Latch Mount is GoPro’s newer system, using magnets for alignment and dual latches for retention. GoPro describes it as a way to move a HERO13 Black between mounting setups quickly.
How to Attach the Camera Step by Step
Attaching a GoPro takes under a minute once the interfaces match: align, insert, tighten by hand, set the angle, and test.
- Match the connection. Use the stick’s GoPro buckle or finger mount. If the stick only has a 1/4-20 screw, thread on a GoPro tripod adapter first.
- Seat the camera. Align the mounting fingers with the buckle, insert the mounting screw, and tighten firmly by hand. For a threaded connection, screw the camera or adapter on straight — no cross-threading.
- Lock the angle. Point the camera where you want it and tighten the joint so it cannot rotate during movement. GoPro recommends keeping the stick in line with the camera body.
- Test before you move. Confirm the camera is locked into the buckle or the screw is fully engaged, then wiggle the handle and joint to check for play.
On a 360 camera, that last step matters more. GoPro says most selfie sticks can be made invisible with MAX when the stick, mount, and base stay within the camera’s blind spot and the pole runs vertically in line with the camera. The mount and base can’t be wider than the camera, or they’ll show up in the frame.
What to Check Before You Buy a Stick
A stick that physically fits can still be wrong for your shooting: check payload, locking, and waterproofing before you trust it over water or at speed.
GoPro’s own lineup shows the range.
For third-party sticks, the requirements are simple: a standard GoPro mounting interface or a standard 1/4-20 screw, plus a joint that stays locked under vibration. If you’d rather compare tested options than gamble on a no-name pole, this roundup of top rated GoPro selfie sticks covers the ones worth the money. GoPro’s own guide to the best selfie sticks for GoPro cameras is the official reference for what the company recommends.
| Mount Type | Best For | Notes |
|---|---|---|
| GoPro mounting fingers | Most GoPro models | Works with standard GoPro buckles |
| 1/4-20 tripod thread | HERO12 Black, MAX2 | No adapter needed on threaded sticks |
| Magnetic Latch Mount | HERO13 Black | Magnets align, dual latches retain |
| Tripod adapter | Any GoPro on a threaded stick | Converts fingers to 1/4-20 |
Common Mistakes That Cost People Their Cameras
Most failures trace back to a loose screw, an off-axis mount, or an overextended pole — all avoidable with a ten-second check.
- Loose or cross-threaded screws. Hand-tighten only; a stripped 1/4-20 thread won’t hold a camera.
- Off-axis mounting on 360 cameras. The pole shows up in the shot if it isn’t aligned with the camera body.
- Overextending the stick. Past its locking limit, joints flex and the camera swings.
- Assuming the camera’s waterproofing covers the stick. Waterproofing is product-specific — GoPro describes 3-Way 2.0 as waterproof, but that doesn’t extend to every stick, screw, or adapter.
- Skipping the pre-use inspection. Check the mount, screw, buckle, and joints for damage before every outing, and keep a secondary plan when shooting near water, traffic, or cliffs.
Common Questions
Can I use a regular camera selfie stick with my GoPro?
Yes, if the stick has a standard 1/4-20 screw and you add a GoPro tripod adapter. GoPro’s adapters are designed to attach any GoPro to an accessory with a standard 1/4-20 mount. Without an adapter, the camera’s mounting fingers won’t connect to a threaded stick.
Why does the pole show up in my 360 footage?
The mount, base, or pole is sitting outside the camera’s blind spot. Keep the stick in line with the camera body, make sure no part of the mount or base is wider than the camera, and the pole should disappear from the shot.
Is my GoPro selfie stick waterproof?
Only if that specific product is rated for it. GoPro describes some products, like the 3-Way 2.0, as waterproof, but that rating doesn’t transfer to your stick, screw, or third-party adapter. Check the stick’s own specs before taking it into water.
Sources
- GoPro. “The Absolute Best Selfie Sticks for GoPro Action Cameras” Official guidance on selfie stick compatibility and GoPro’s own stick lineup.
- GoPro. “Mounting: It’s What Makes a GoPro, a GoPro” Explains mounting interfaces and the Magnetic Latch Mount system.
- GoPro. “Tripod Adapters” Confirms adapters connect any GoPro to a standard 1/4-20 mount.