How to Measure Your Truck Rear Seat for Seat Covers? | Split, Depth, Backrest

Measure a truck rear seat in its normal driving position: overall cushion width, cushion depth, backrest height, plus each split section separately.

A rear bench that folds up against the cab wall, a 60/40 split with a fold-down armrest, and a 40/20/40 with a console can all share the same cab footprint and none of them take the same cover. Getting the tape right is less about accuracy than about knowing what to put it on — so the numbers below are organized around the seat you actually have.

Custom-fit covers are usually ordered by model year, cab style, trim, seat split, and folding mechanism rather than by measurements alone. Universal and hammock-style covers lean harder on the tape. Either way, a few minutes with a cloth tape and a phone camera saves the return shipping.

How to measure your truck rear seat: the sequence that works

Start on level ground with both rear doors open and the seat in its normal driving position — not folded, not reclined. Photograph first, then measure.

  1. Photograph the seat before touching the tape: the split line, headrest style, armrest, belt buckles, LATCH anchors, release levers, and fold points. These photos are what a fit-chart conversation needs.
  2. Overall cushion width: left seating edge to right seating edge, door to door, tape straight but not pulled tight.
  3. Each split section separately. On a 60/40, write down which side is which. Skip this and a one-piece cover will fight the center crease every time you fold.
  4. Cushion depth: front edge of the cushion to the seatback.
  5. Backrest height: cushion junction to the top of the backrest. Note whether headrests are integrated, removable, or on posts — and if removable, whether they can come off at all.
  6. Backrest width if the product instructions request it; not every brand does.
  7. Center armrest: width, hinge direction, and whether it folds down or needs a pass-through. A 40/20/40 usually needs a cover with the correct armrest opening.
  8. Fold the seat as designed — truck rear seats often fold upward against the rear wall rather than forward. Decide whether the cover has to stay installed in both positions, and check that hinges, straps, latches, and under-seat storage stay reachable.

Write everything in inches and compare each number against the manufacturer’s fit chart, not against truck class. Two trucks sold as “full-size” can have completely different seat geometry.

What Actually Decides Whether A Cover Fits

Seat configuration decides more than any single dimension. A 60/40 rear bench needs separate cover sections so each side folds independently; a one-piece cover can interfere with the center crease and the folding function itself. A 40/20/40 bench needs the right split plus a correctly placed armrest opening.

For custom-fit covers, the vehicle details matter more than the tape. Confirm model year, make, model, cab style, trim, seat split, headrest arrangement, and folding mechanism with the seller before ordering — nominally similar trucks have different seat shapes and mechanisms.

Published size ranges give a rough sanity check, though they are product-specific and not a truck-seat standard:

Published Size Listed Dimensions Market Described
Regular split rear cover 54 in wide x 58 in long (includes hammock) Most cars, small trucks, regular SUVs
Fitted regular split cover 54 in wide x 18 in deep x 22 in high backrest Mid-size trucks per fit guides
XL split rear cover 60 in wide x 64 in long (includes hammock) Full-size trucks, large SUVs
Crew-cab full-size (hammock style) XL only — one listed size F-Series, Silverado, Tundra, Sierra, Titan, Ram

Note the trap in those numbers: hammock dimensions include extra material extending forward from the seat.

Once your numbers and configuration are written down, the next decision is which product line actually uses them — our tested truck rear seat covers buying guide pairs each split style with covers built for it.

Where Measuring Goes Wrong — And What NHTSA Says About Safe Covers

Most bad orders trace back to five habits: measuring the truck bed instead of the passenger seat, measuring only total width on a split bench, ignoring cushion depth and backrest height, blocking LATCH anchors and release levers, and treating “universal” as a promise that every truck fits. Measuring with the seat folded also produces numbers that mean nothing once the seat drops back down.

Safety is the part nobody photographs. Seat covers must not interfere with seat-mounted side airbags, and installation instructions typically require airbag tags or openings to face the door, with cutouts aligned to headrest guides, armrests, and levers. The safest rule is simple: if a cover hides an airbag tag or blocks a buckle, don’t install it.

American Trucks’ published installation guides show the level of detail worth matching — American Trucks’ rear seat cover installation guide covers section-by-section fitting for split benches.

Take the photos, measure the seat in its normal position, note the split and every access point, then match the whole list against the fit chart before you order. Ten minutes of tape work beats a return.

Common Questions

Do I measure the seat folded or upright?

Always upright, in the normal driving position. Folding changes both the cushion depth and the backrest profile, so folded numbers won’t match a fit chart. Once upright measurements are recorded, fold the seat separately just to confirm the cover won’t block hinges, latches, or under-seat storage.

Can one cover fit both sides of a 60/40 bench?

No. A 60/40 bench needs two cover sections because each side folds independently. A single piece can bind the center crease and interfere with the folding function. Measure and record the 60 side and the 40 side as separate numbers, and confirm which side is which with the seller.

Are pickup rear seats the same as SUV rear seats?

Often not. Truck rear seats frequently fold upward against the cab wall rather than forward, and crew-cab benches may include under-seat storage or fold-flat mechanisms. That changes which parts a cover must stay clear of, so measure your specific truck rather than a similar SUV.

Sources

Scroll to Top