Specs are compiled from manufacturer listings and verified buyer reviews and can change over time — please confirm the key details on the product page before buying.
If your hot water has gone lukewarm, cold, or scalding, the thermostat is usually the part that failed — not the whole tank. You do not need a new water heater. You need the right replacement thermostat that fits your Whirlpool unit and holds a steady temperature. This guide covers six thermostats and tune-up kits that fit Whirlpool heaters, explains which one suits which repair, and points out the fit quirks that decide whether a swap takes fifteen minutes or turns into a return.
This guide is built by comparing the manufacturers’ published specifications and the patterns across verified customer reviews, so you get each pick’s real strengths and trade-offs instead of marketing spin.
Every part below states its voltage range and adjustment limits plainly, so you can match it to your tank before you order anything. Start with the reach, then check the temperature dial: that is how you buy a whirlpool hot water heater thermostat.
Top Picks


How To Choose The Best Whirlpool Hot Water Heater Thermostat
A water heater thermostat is a temperature-controlled switch. It senses how hot the water is and clicks the heating elements on or off to hold your setting. On a two-element Whirlpool tank you normally have two of them — an upper and a lower — wired so only one draws power at a time. That is what “non-simultaneous” means on the packaging.
Buying the wrong one is almost always a fit or voltage problem, not a quality problem. These five checks settle it before you spend anything.
Match the voltage range to your heater
Look at the data plate on your tank for the voltage. Most residential Whirlpool heaters run on 240 volts, and several kits here cover 120V to 480V, which spans what you will find in a home. If the thermostat listing does not state a range, treat that as a gap you need to verify with the seller.
Check the temperature adjustment range
The temperature dial sets how hot the tank delivers. The kits here mostly adjust from 90 °F to 150 °F. That 150 °F top is a hard ceiling on the dial, and it matches where safety guidelines usually cap residential tank temperature. If you have been running hotter than that, this class of part will not do it.
Know the difference between the dial and the high limit
The dial is what you set. The high limit is a separate safety cutoff that trips if the tank overheats, and on most of these parts it sits at 170 °F with a manual reset button. A heater that blows its reset repeatedly is telling you something else is wrong — a stuck element or a bad lower thermostat. Do not just press the button and walk away.
Upper and lower are not the same part
An upper thermostat usually carries the high-limit reset. A lower thermostat typically does not. That is why the kits pair a KST203-style upper with a KST200-style lower, and why buying a single thermostat only makes sense when you already know which one failed.
Fit is the number-one return reason
The mounting footprint and the size of the part vary more than you would expect from parts that do the same job. One of the kits here is far larger than another. Measure the opening on your heater and compare it against the listed dimensions before ordering.
Side-by-Side Comparison
| Model | Best For | Voltage | Temp Range | High Limit | Amazon |
|---|---|---|---|---|---|
| EWH-00 Kit (Upper + Lower)★ Best Overall | Most Whirlpool swaps | 120V–480V | 90 °F–150 °F | 170 °F | Amazon |
| Rheem UV11699Single-Part Fix | Single-thermostat repair | — | 90 °F–150 °F | Manual reset | Amazon |
| LONG TERM KST200&203 | Compact two-part kit | 120V–480V | 90 °F–150 °F | — | Amazon |
| TAIACE EWH-00 (UL) | Certified buyer | 120V–480V | 90 °F–150 °F | Built-in switch | Amazon |
| NISHCON EWH-01 Tune-Up Kit | Full rebuild | 240V / 208V | 90 °F–150 °F | 170 °F | Amazon |
| Whirlpool 61006116 | Genuine factory part | — | — | — | Amazon |
Detailed Reviews
1. EWH-00 Water Heater Thermostat Kit for Double Element Heater
Our pick — 4.5+★ from 300+ verified ratings; the strongest balance of quality and price.
Both thermostats in one bag, so a cold shower gets fixed in a single trip.
Here is the part to buy if you do not yet know which thermostat died. You get one upper and one lower thermostat in the box — the KST200 and KST203 pattern — so you can replace the whole temperature chain instead of guessing. Both are rated 120V to 480V, which covers the 240V wiring in a typical Whirlpool tank.
The adjustment dial runs from 90 °F up to 150 °F (32 °C to 66 °C), and there is a separate high limit at 170 °F. That 170 °F cutoff is a manual-reset safety switch that kills power if the tank overheats. It matters because a tripped high limit is the most common false alarm on these heaters — it looks exactly like a dead thermostat. Buyers rate this kit highest for reliability — it holds the setting and keeps the tank cycling — and its compatibility list is the longest here, with Whirlpool named first.
Two honest notes before you buy. First, size runs the opposite way from the TAIACE kit — the TAIACE measures 5.2″W x 2.1″H, while this one’s package runs 5.16 x 2.83 x 2.24 inches. So measure your opening instead of assuming either will drop in. Second, the mounting fit and finish draws mixed feedback; a few buyers found the alignment fussy. That is not a reason to skip the brand, just a reason to keep the receipt until the tank is hot again.
What earns the top spot
- Upper and lower thermostats together — one order, whole repair
- 120V to 480V covers standard residential Whirlpool wiring
- Explicit 90 °F to 150 °F dial plus a 170 °F high limit at the reset
- Compatibility list names Whirlpool, Rheem, AO Smith, State and more
Where it can trip you up
- Mounting alignment is fussy on some tanks; check your opening first
- No element included, so a burned-out element needs a second part
Buy this when: your Whirlpool heater went cold or erratic and you want the upper and lower swapped in one job.
Hold off if: you already tested and know only one thermostat failed — a single-unit part saves the leftover.
2. Rheem UV11699 Electric Water Heater Thermostat
One thermostat, a manual reset button, and a brand that already makes heaters.
If your Whirlpool has already told you which thermostat failed, this is the targeted version of that repair. It replaces APCOM-style thermostats and the maker lists Whirlpool alongside Rheem, Ruud, Richmond, GE, State, Kenmore, Bradford White, AO Smith, American, Craftmaster, Lochinvar, Reliance and Mor-Flo as fits. You are buying one part and one part only.
The dial spans 90 °F to 150 °F. A manual reset high limit sits on the part, which helps stop overheating before it becomes a bigger problem — press it back in only after you have found out why it tripped. Inside, a bi-metal disc flexes with heat and snaps the contacts apart, which the maker credits for lasting performance under the high electrical loads a heater draws.
The catch is scale. This sits on a metal-and-plastic body with a one-year limited warranty, and that is the whole package — no lower thermostat, no element, no gaskets. If both thermostats are suspect, the two-part kits here cover more ground for a similar outlay.
Who this suits: a Whirlpool owner who has already traced the fault to one thermostat and wants a like-for-like APCOM-style replacement.
What to weigh: buying a single part means a second order if the other thermostat turns out to be the weak link too.
Right call for a confirmed single failure: it does one job with a manual reset on board.
Reconsider if: you are still diagnosing — the two-thermostat kits here remove the guesswork entirely.
3. LONG TERM KST200&203 Electric Water Heater Thermostat Kit
The slim two-thermostat kit for tight recesses behind a Whirlpool cover plate.
Look here first if space is tight. This kit measures 2.17″W x 5″H, which is the compact end of the scale — the TAIACE kit below is listed at 5.2″W x 2.1″H, and the two are effectively the same pair of parts rotated and boxed differently. If your heater’s thermostat pocket is snug, that number is the one that decides the job.
One bag covers both ends of the tank: you get an upper and a lower thermostat, non-simultaneous (only one element heats at a time), wired for 120V to 480V. The dial adjusts from 90 °F to 150 °F, so you can set a comfortable tank temperature. The parts are Thermo-O-Disc style, so they interchange with APCOM style — Whirlpool is the first brand named on the fit list, followed by Bradford White, Craftmaster, GE, Kenmore, AO Smith and the rest of the usual roster. The maker backs it with a one-year warranty.
What you should know before ordering: this kit stops at the thermostats. Unlike the NISHCON tune-up kit, there are no heating elements or gaskets in the box, so if your water is merely slow rather than cold, you may be replacing the wrong part.
Why it earns a slot
- 2.17″W x 5″H footprint suits cramped thermostat pockets
- Both thermostats included, so the whole chain gets refreshed
- TOD-style body swaps with APCOM-style fittings
- Whirlpool heads the compatibility list
What to plan around
- Thermostats only — no elements or gaskets included
- High-limit figure is not spelled out; confirm with the seller if your reset keeps tripping
Best fit for a snug tank: compact upper-plus-lower replacement that drops into a tight pocket.
Look elsewhere if: you also need elements — go straight to a tune-up kit and save the second order.
4. TAIACE EWH-00 Electric Water Heater Thermostat Kit
Same upper-and-lower pair, but with a UL mark printed on the housing.
For anyone who wants paperwork behind a part that sits behind a live electrical panel, this is the kit that states it plainly: the thermostats are UL certified. The contacts are copper, which the maker ties to faster switching and longer service life. You get one KST200 lower and one KST203 upper in the box.
The spec sheet reads close to its stablemates — 90 °F to 150 °F adjustment, TOD-style body interchangeable with APCOM style, 120V to 480V, and a built-in safety switch to prevent overheating. It lists Whirlpool, GS Wood, Kenmore, GE, AO Smith, State, Reliance, Mor-Flo, Rheem, Bradford White, Lochinvar, Richmond, Craftmaster and Ruud as fits, which is about as broad as this class gets. It weighs 0.22 kg and measures 5.2″W x 2.1″H, so it is a wider, flatter block than the LONG TERM kit.
The snag is longevity. Some buyers report their unit gave out after roughly two months, which is why durability reads as the mixed item on this one even while function and quality read positive. Treat the one-year warranty as the thing you actually lean on if it fails early.
Why you would pick it: a UL-certified upper-and-lower pair with copper contacts, sold as a complete kit with a one-year warranty for the buyer who wants the certification on record.
The trade-off: durability is the weak spot here — a few units quit early, so keep your receipt and use the warranty window.
Pick it for confidence: UL certification (a safety stamp from a national testing lab) and a complete kit make it a defensible choice for a cautious repair.
Think twice if: you want the longest-lived part available — the NISHCON kit below leans on element treatment instead.
5. NISHCON EWH-01 Electric Water Heater Tune-Up Kit
Everything inside the tank gets replaced at once — elements, gaskets, thermostats.
This is the one to reach for when the water is not just cool but slow to heat, or when you would rather not pull the tank apart twice. The kit carries four pieces: two heating elements at 4500W on 240V (3500W at 208V) with gaskets, plus an upper and a lower thermostat. Each element runs 13-9/16 inches, and the chrome-coated heating zone is what the maker ties to longer element life.
On the thermostat side you get the same 90 °F to 150 °F dial, but a high limit of 170 °F — the safety cutoff that kills power if the tank overheats. That is 20 °F above the 150 °F dial ceiling on the LONG TERM kit and the highest cutoff in this group. It is rated 120V to 480V, swaps with APCOM style, and lists Whirlpool, AO Smith, GE, Richmond, Ruud and Bradford White among fits. The description frames it as a dual-element or 30-gallons-and-up job, so check your tank size first.
Two things to weigh. The kit is built to fix a slow, weak or dead heater rather than a cold one alone. And quality control is where it splits opinion — a small share of units turn up faulty on arrival, which is the counterweight to a strong reputation for fit and function.
The case for the full kit
- Elements, gaskets and both thermostats in one box
- 4500W at 240V output sized for full-size tanks
- Chrome-coated heating zone aimed at longer element life
- 170 °F high limit gives the highest cutoff in this group
The honest counterweight
- Occasional units arrive faulty — inspect before install
- Only meaningful on a 30-gallon-plus dual-element tank
Where it wins: a heater that is slow, weak, or clicking its reset — rebuild the hot side in one pass instead of buying parts piecemeal.
skip it if: you have a small single-element tank or a confirmed thermostat-only fault.
6. Whirlpool 61006116 Heater and Thermostat Assembly
The factory-numbered part, for the owner who refuses to gamble on an aftermarket clone.
Model number 61006116, manufacturer Whirlpool, described as a genuine replacement part. That is the whole appeal: no cross-referencing a compatibility list, no wondering whether an APCOM-style body really fits your tank. If your heater manual points to this assembly, you buy this assembly.
The catch is what the listing does not say. There is no stated temperature range, no voltage figure, and no high-limit number (the safety cutoff that stops overheating) — so if you want to know the dial tops out at a specific degree before ordering, this listing leaves you to check the manual. It is also a heater-and-thermostat assembly rather than a two-thermostat kit, at 500 watts and 3.2 ounces, so it suits the specific repair it was made for and not a generic tune-up.
What it does deliver is a straightforward job. Installations run around fifteen minutes, and the part runs fine over time once in. For a Whirlpool-badged tank where matching the original part matters more than squeezing every degree out of the dial, this is the shortest path to hot water again.
The real appeal: a genuine Whirlpool part number with no compatibility guesswork and a fifteen-minute install.
The gap to know about: the listing states no temperature range or voltage, so confirm the fit against your manual before you buy.
Choose it for originality: a matched factory assembly for a Whirlpool heater that calls for exactly this part.
Look at the kits instead if: you want a stated temperature dial and high limit spelled out, or you need two thermostats.
Know the Specs
Voltage Range (120V to 480V)
The voltage range tells you which heaters a thermostat can be wired into. A part rated 120V to 480V covers the 240V supply in a typical home Whirlpool tank. If a listing gives no voltage figure at all, verify it with the seller before you cut power and open the panel.
Temperature Adjustment Range (90 °F to 150 °F)
This is the dial range — how hot the tank will deliver. Most kits here run 90 °F to 150 °F. The dial sets normal temperature; it is not a safety device. Pushing it past its stated top does not get you hotter water safely.
High Limit and Reset (170 °F)
The high limit is the safety cutoff that trips when the tank overheats, and on several parts here it sits at 170 °F with a manual reset button. If that button keeps popping, stop resetting it — a stuck element or a failed lower thermostat is usually the real cause.
Upper Versus Lower Thermostat
A two-element heater uses an upper and a lower thermostat, wired non-simultaneously so only one heats at a time. The upper usually carries the high-limit reset. Kits pair a KST203-style upper with a KST200-style lower; buying a single thermostat only makes sense once you know which one failed.
Common Questions
Will these thermostats fit my Whirlpool water heater?
How do I know whether the upper or the lower thermostat failed?
What does the 170 °F high limit reset actually do?
Is a UL-certified thermostat better than an uncertified one?
Can I replace just the thermostat without the whole kit?
How long does a replacement Whirlpool thermostat last?
Do I need to drain the tank to change a thermostat?
Will a 240V thermostat work in a Whirlpool heater?
Do these kits work with heaters other than Whirlpool?
What if the replacement thermostat trips the reset right after install?
The Bottom Line
For most people replacing a thermostat in a Whirlpool tank, the EWH-00 Water Heater Thermostat Kit is the sensible pick — upper and lower in one bag, a stated 170 °F high limit, and a brand list that starts with Whirlpool. If you have already traced the fault and only one part needs swapping, the Rheem UV11699 gets you a single thermostat and a manual reset (a button you press to restart the heater after it trips). And when the water is slow rather than cold, or you would rather open the tank once, the NISHCON EWH-01 tune-up kit puts elements, gaskets and both thermostats in the same box so one repair covers the whole hot side.
One genuine nudge: the EWH-00 kit is the crowd favorite here — 4.5+ stars across 300+ ratings, with reliability reading as the top point buyers agree on. If you want to be done in one order, that is the one to reach for first.
How we choose
We do not accept paid placement. Every pick is matched to a real buyer and a real use-case; we do not hands-on test units.
Sources
Specifications: manufacturer listings and product documentation. Review insights: verified customer reviews, as of November 2026. Pricing: not shown on this page (it changes often); check the current price via the retailer link.
As an Amazon Associate, Tactical Gear Guy earns from qualifying purchases. This does not affect which products we feature.



