A surface hand pump typically lifts water from about 20–25 feet down, while a deep-well hand pump with its cylinder in the well can reach far deeper.
One wrong measurement — the well’s total depth instead of the distance to the water surface — is why so many shallow-well pumps fail to prime on day one. The number that matters is suction lift: the vertical distance from the pump’s inlet down to the water level, not the bottom of the hole.
What Is Suction Lift, And Why Does It Cap A Pump?
Suction lift is the vertical distance from a pump’s suction valve or inlet to the water surface. Atmospheric pressure does the actual work: it pushes water up into the suction pipe, so a pump never truly pulls a column of water upward on its own.
Standard atmospheric pressure corresponds to roughly 34 feet (10.4 meters) of water in theory — not a usable rating. A 2024 study in Water Practice & Technology on No.6 hand pumps measured a theoretical maximum suction near 31 feet under test conditions, yet reported real-world field suction of only 21.0 feet — against 26.5 feet in model tests. Air leaks, vapor formation, pipe friction, and pump design eat the difference.
How Deep Can A Hand Pump Draw Water In Practice?
For a conventional surface suction hand pump, plan on 20–25 feet as the realistic ceiling — with margin below whatever the manufacturer publishes. Simple Pump’s brochure rates its PHA-2-S suction pump at a maximum lift of 25 feet at sea level, minus 1 foot of lift per 900 feet of elevation gain.
Manufacturer specs tell the same story. A cast-iron pitcher pump (part number CLPP) is specified for water depths of 25 feet or less. Mitchell-Lewis lists Simmons and Merrill pitcher pumps as shallow-well units for water levels under 30 feet, while citing a 25–30-foot maximum suction lift. One pump instruction sheet splits its models even lower: 25 feet for the HC-1005/1006 and 20 feet for the HC-1007/1008. All share a 1-1/4-inch NPT inlet.
| Pump Type | Realistic Maximum Lift | Best For |
|---|---|---|
| Cast-iron pitcher pump (CLPP) | 25 ft or less | Shallow wells, garden and farm use |
| Pitcher pumps (Simmons/Merrill) | 25–30 ft max suction lift | Water levels under 30 ft |
| Simple Pump PHA-2-S | 25 ft at sea level, minus 1 ft per 900 ft elevation | Lift-critical shallow installations |
| HC-1005 / HC-1006 | 25 ft (7.6 m) | Standard shallow-well draws |
| HC-1007 / HC-1008 | 20 ft (6 m) | Tighter lift margins, lower head |
| Deep-well hand pump (in-well cylinder) | Up to 325 ft on Simple Pump’s model | Water levels below the suction limit |
Below the suction limit, the fix is a deep-well hand pump: the cylinder sits down in the well with a connecting rod running up to the handle, so it pushes water upward instead of relying on surface suction. Simple Pump rates its deep-well hand pump for a static water depth up to 325 feet, and its shallow-well model for less than 25 feet. That 325-foot figure is specific to that pump — real capacity depends on cylinder, pipe, rod, well diameter, and discharge pressure. a tested roundup of well hand pumps covers the models side by side.
How Do You Measure And Set Up For Your Well?
Measure from the pump or suction valve down to the lowest seasonal water level — the low point in dry season or during pumping, not the year-round average. A well can be 100 feet deep and still work with a 25-foot pump, as long as the water table sits inside the lift window.
- Measure vertically from the suction inlet to the water surface, never the well’s total depth.
- Keep the suction line airtight. Even a small leak can stop priming or sharply cut lift.
- Match the pipe and thread to the manufacturer’s spec — several pitcher pumps use 1-1/4-inch NPT.
- Prime before operation where required; a surface pump cannot lift water with air in the line.
- Expect less performance at elevation, with long or narrow suction pipes, restrictive fittings, dirty valves, or fast stroking.
The 2024 study’s field-versus-model gap is the practical lesson: published maximums are ceilings, not targets. Installing a 25-foot pump where the water drops to 25 feet leaves no room for error; reliability needs margin below the number on the box.
One more caution: garden and pitcher pumps sold at retail are often listed for general, pond, farm, or non-drinking use. Potable water requires verified sanitary materials, a protected wellhead, and compliance with local rules. Protect the wellhead from surface runoff, and anchor the pump properly.
Common Questions
Does well depth or water level decide if a pump will work?
Water level decides it. Suction lift is measured from the pump inlet to the water surface, so a deep well whose water table stays within 20–25 feet works fine with a shallow-well pump. Always measure the lowest seasonal level, not the well’s total depth.
Why do two pumps with the same rating perform differently?
Pipe diameter, fitting restriction, air leaks, valve condition, and elevation all change real lift. The 2024 study recorded 21.0 feet of field suction against 26.5 feet in model tests on the same pump class — hardware and setup account for that gap.
Can a hand pump lift water from 100 feet down?
Only a deep-well hand pump with its cylinder installed in the well can. Surface suction cannot reach that far. Simple Pump rates its deep-well hand pump for static water depth up to 325 feet, though every installation differs by cylinder, pipe, and well diameter.
Sources
- Water Practice & Technology. “Evaluating performance and suction limits of No.6 hand pumps” Source for field vs. model suction data and atmospheric lift limits.
- Simple Pump Co. “Simple Pump Brochure” Manufacturer lift ratings for suction and deep-well models.
- Mitchell-Lewis. “Hand Pumps” Pitcher pump suction lift specifications.