How to Connect a Wireless Controller to Xbox Series S | Pair Button Steps

Your Xbox Wireless Controller pairs with the Series S through the console’s Pair button, not Bluetooth — a hold on each button finishes the link.

The moment the Xbox button stops flashing and holds steady, the console has found your controller. Pairing is a two-button job, and it fails most often because one of those presses is skipped. Per Xbox Support, the console reaches out for about 20 seconds after you tap its Pair button — miss that window and nothing happens.

What You Need Before Pairing

  • Power. The controller needs working batteries even if the Xbox button lights up; low cells are a known cause of pairing faults. The console must be powered on, not in instant-on standby.
  • Controller type. The Xbox Wireless Controller that ships with the Series S is the standard match. Xbox One Wireless Controllers also work with the Series X|S. Xbox Elite Wireless Controller Series 2 and the Xbox Adaptive Controller are supported accessories, though behavior shifts by device and firmware.

Xbox 360 pads are a different story — the Xbox Accessories app does not support them, and they do not pair with the Series S.

How Do You Pair a Controller to the Console?

Press the console’s Pair button first, then hold the controller’s Pair button — in that order — until the Xbox button lights solid. Skip the console press and the controller broadcasts to nothing.

  1. Turn on the Xbox Series S.
  2. Press and release the Pair button on the console.
  3. Within roughly 20 seconds, press and hold the controller’s Pair button. It sits on the top edge, near the USB port.
  4. Watch the Xbox button flash while the two devices talk, then hold steady once connected.
  5. Press the Xbox button and pick a profile.

That steady glow is your confirmation the Series S sees the controller.

Connection Where It Works What To Expect
Xbox Wireless Series S console Press both Pair buttons; Xbox button holds steady
Bluetooth Windows 10/11, Android, Apple, smart TVs, Meta Quest Paired through the device’s Bluetooth menu, not the console
USB cable Series S (fallback), Windows PC Needs a data-capable cable; also works with dead batteries
Xbox One pad Series X|S Pairs the same way; USB-to-micro-USB for wired
Elite Series 2 / Adaptive Series X|S Supported; firmware behavior varies by device
Xbox 360 pad Not supported No pairing; Xbox 360 controllers are excluded

Why Pairing Fails — And How to Fix It

Most failed pairings trace to one of four causes: the console button never got pressed, Bluetooth settings were used instead, the cable can’t carry data, or the batteries are weak.

The console button was skipped. The controller only listens for a short window after the console starts broadcasting. Press the console Pair button again and hold the controller button within those seconds.

Bluetooth was the wrong menu. The Series S talks to its controllers over Xbox Wireless. Bluetooth pairing exists for phones, PCs, tablets, and TVs — see Microsoft’s guidance on connecting a wireless controller for device-by-device steps. The console has no Bluetooth setting to pair through.

The cable only charges. If you fall back to USB, use one that carries data. A charge-only cable powers the controller but won’t link it, and it also blocks firmware updates over wire.

The controller needs a reset. Hold the Xbox button for 5–10 seconds until it shuts off, wait a few seconds, and power it back on. Fresh batteries belong here too.

For a spare or second pad, this roundup of the best wireless controllers for the Xbox Series S covers tested picks.

Bluetooth, Firmware, and Other Devices

One controller can serve several devices, but Bluetooth and console pairing are not the same link. A controller connected to a phone or PC may need to be switched back or paired again.

Controllers included with the Series X|S do support Bluetooth. You can tell a Bluetooth-capable model by the plastic around the Xbox button: on Bluetooth versions it is part of the front faceplate, and on older non-Bluetooth versions it sits in the top section near the bumpers. The Series X|S controller also needs current firmware to work with iOS devices.

Updates install wirelessly, over USB, or on a Windows PC through the Xbox Accessories app. If an update stalls, disconnect extra accessories, power-cycle the console, try a USB cable, or finish on a PC. Bluetooth-connected controllers may show reduced features in the Accessories app.

Common Questions

Does the Series S have a Bluetooth menu for controllers?

No. The console links its controllers over Xbox Wireless, so there is no Bluetooth pairing screen for them. Bluetooth is for connecting the controller to phones, PCs, tablets, and TVs instead. Trying to pair through console Bluetooth settings is a common reason a connection attempt goes nowhere.

Can I use an old Xbox One controller on the Series S?

Yes. Xbox One Wireless Controllers work with the Series X|S and pair the same way as the newer pad. For wired fallback, older controllers use a USB-to-micro-USB cable, while newer Xbox Wireless Controllers use USB-to-USB-C.

Why does the Xbox button keep flashing and never stay on?

A flashing light that never settles means the handshake did not complete. Press the console’s Pair button again, then hold the controller’s Pair button inside the roughly 20-second window. Weak batteries are the other frequent culprit, so install fresh cells or fully recharge before retrying.

Sources

Scroll to Top