A 30-inch range hood needs at least a 30-inch clear cabinet opening, 12 inches of cabinet depth, and 24 to 30 inches from the cooking surface to the hood’s lowest edge.
A nominal 30-inch hood does not guarantee a 30-inch footprint, and the cabinet you have is the number that decides the fit. Measure the cooking surface, the clear opening between cabinet sides, the cabinet depth, and the vertical gap to the hood before anyone touches a saw. The payoff is a hood that captures smoke instead of spilling it into the room — and a cutout you only make once.
What Do You Measure Before Buying a 30 Inch Hood?
Four measurements decide whether a 30-inch hood fits: cooktop width, cabinet opening width, cabinet depth, and clearance above the cooking surface. Take all four with a tape measure, then cross-check them against the hood’s own installation manual, because depth and projection vary by model.
Start with the actual left-to-right width of the cooking surface, not the nominal appliance size. A 30-inch hood is built for a 30-inch appliance, and the hood should be at least as wide as the cooktop — wider generally captures better. From there:
- Cooktop width: measure the real cooking surface edge to edge.
- Cabinet opening: measure the clear width between the cabinet sides. A representative 30-inch installation guide specifies a 30-inch (76.2 cm) minimum.
- Cabinet depth: the same guide’s diagram specifies 12 inches (30.5 cm).
- Vertical clearance: measure from the cooking surface up to where the hood’s lowest point will sit.
Two more dimensions round out the picture. A representative installation diagram lists 18 inches (45.7 cm) minimum from upper cabinet to countertop and a 36-inch (91.4 cm) base-cabinet height. Confirm the vent route through the wall or ceiling has room before cutting anything — the duct has to go somewhere.
| Measurement | Typical Spec | Why It Matters |
|---|---|---|
| Cabinet opening width | 30 in (76.2 cm) minimum | Hood must seat between cabinet sides |
| Cabinet depth | 12 in (30.5 cm) | Controls how far the hood projects |
| Clearance, electric surface | 24–30 in above cooking surface | Too low is a fire risk; too high loses capture |
| Clearance, gas surface | 30 in minimum in some model guides | Gas burners run hotter; manuals may demand more |
| Upper cabinet to countertop | 18 in (45.7 cm) minimum | Keeps the hood clear of the work zone |
| Base cabinet height | 36 in (91.4 cm) | Sets the countertop reference line |
| Cooking surface width | Match or exceed with hood width | Hood narrower than cooktop loses smoke |
How High Should a 30 Inch Range Hood Sit Above the Cooktop?
Measure from the cooking surface itself, not the countertop — the grates or elements sit above the counter and that gap counts. The range or cooktop manufacturer’s instructions can impose a stricter minimum than the hood manual, and when they do, the stricter number wins. Once you know the clearance, check the hood you want against our roundup of the best 30 inch white range hoods to see which models match your opening.
What Venting and Code Rules Apply?
The 2024 International Residential Code, Section M1503.3, requires domestic cooking exhaust to discharge outdoors through a duct with a smooth interior, an airtight seal, a backdraft damper, and no connection to other exhaust systems. It may not terminate in an attic, crawl space, or any interior building area.
The 2021 IRC carries the same discharge, duct, damper, and termination language. The IRC exception allows listed and labeled ductless hoods when installed per the manufacturer’s instructions and where other mechanical or natural ventilation exists. Local jurisdictions adopt their own editions and amendments, so the local building department has the final say. Section M1503.3 of the 2024 IRC lays out the full requirement.
Listing matters too. The 2021 IRC requires overhead hoods and non-integral-fan downdraft equipment to be listed and labeled under UL 507, and integral-fan overhead hoods to comply with it. On airflow, older IRC provisions flag 400 CFM as the threshold where makeup air is required at roughly the exhaust rate, with a damper tied to the exhaust system. Some jurisdiction-specific material sets 100 CFM at 0.10 inches water gauge where a hood satisfies local kitchen ventilation rules — that figure is local, not national. Confirm the adopted local code before specifying a high-CFM model.
Which Measuring Mistakes Cause the Most Rework?
The costliest error is trusting the label: a “30-inch hood” is not a guaranteed 30-inch physical width, and it will not fit every 30-inch cabinet. Measure the unit you plan to buy, not the spec sheet’s headline number.
Other repeat offenders:
- Measuring from the countertop instead of the actual cooking surface.
- Mounting below the manufacturer’s minimum, especially over gas burners.
- Hanging the hood above 30 inches and wondering why smoke escapes.
- Skipping the range manual when it demands more clearance than the hood guide.
- Cutting cabinets before confirming the exact opening, depth, duct location, and electrical needs.
- Venting into an attic, crawl space, cabinet, or wall cavity instead of outdoors.
- Tying the hood duct into another exhaust system.
- Assuming a ductless setup is allowed without checking the model and local code.
- Choosing airflow without weighing duct size, makeup air, and noise.
Every number above is model- and jurisdiction-dependent. Treat these figures as a starting frame, then let the specific hood manual and your building department settle the final dimensions.
Common Questions
Can a 30-inch hood go over a 36-inch cooktop?
It can be installed, but capture suffers. The hood should be at least as wide as the cooking surface, and wider is better, so a 36-inch cooktop pairs more naturally with a 36-inch hood. If cabinet space forces a 30-inch unit, expect more smoke spill at the edges and plan to run it on a higher fan setting.
Is 30 inches too high for a range hood?
Thirty inches is the top of the suggested range for a representative 30-inch model, not a violation. At that height capture weakens, particularly over gas burners where some guides demand 30 inches minimum anyway. Going higher is at the installer’s and user’s discretion — just know you are trading performance for headroom.
Do I need a ducted hood or can I use a ductless one?
The 2024 IRC requires cooking exhaust to vent outdoors unless an exception applies. That exception covers listed and labeled ductless hoods installed per the manufacturer’s instructions where mechanical or natural ventilation is otherwise provided. Check your local code and the model’s listing before choosing recirculating.
Sources
- International Code Council. “2024 International Residential Code, Chapter 15: Exhaust Systems.” Source for Section M1503.3 outdoor discharge, duct, damper, and termination requirements.
- International Code Council. “2021 IRC Section M1503.3: Domestic Cooking Exhaust Equipment.” Confirms the same discharge and duct language carried into the 2021 edition.
- International Code Council. “2021 IRC Section M1503.2: Listing and Labeling.” Supports the UL 507 listing requirement for overhead hoods and downdraft equipment.