Hiding TV wires on a wall takes one of three routes: in-wall low-voltage cable routing behind brush plates, a listed in-wall power kit, or a paintable surface raceway when you’d rather not cut drywall.
Wires dangling from a mounted TV look sloppy, and one shortcut many people take — dropping the TV’s ordinary power cord behind drywall — is a genuine code violation and a fire risk. Hide the signal cables yourself in a few hours, or use a listed kit that carries power behind the wall legally. The steps below are ordered from the method most people can finish on a Saturday afternoon to the one that needs no cutting at all.
What Is The Easiest Way To Hide TV Wires?
Routing low-voltage cables through the wall behind brush plates is the easiest no-kit method, and it works when you only need to hide HDMI, Ethernet, coaxial, optical-audio, or USB lines. Signal cables are low voltage, so they can generally pass through drywall without the electrical restrictions that apply to power wiring. The catch is that your TV still needs power at the wall, so this method handles the HDMI tangle but leaves the plug problem to solve separately.
Plan the upper opening behind the TV and the lower opening near your equipment shelf or cabinet, and confirm both fall in the same stud bay before you cut anything. Once the holes are open, feed the cables down, then cap each opening with a brush plate or a listed low-voltage wall plate. Leave enough slack at both ends for the TV to move on its mount and for future service.
Do You Need An In-Wall Power Kit?
Yes — if you want the TV’s power receptacle behind the screen without hiring an electrician, a listed in-wall power kit is the route that keeps you code-compliant. The SANUS SA-IWP1 is a do-it-yourself system that moves power from an existing receptacle to a recessed outlet behind the TV without touching the home’s branch-circuit wiring. The box includes two power grommets, a 10-foot in-wall cable, a 6-foot power cord, a drill bit, and a hole saw, and SANUS states installation takes under 30 minutes.
Legrand sells two related options. The On-Q OQ-HT2302KWH handles power and Class 2 low voltage behind a wall-mounted TV, fits a standard 2 × 4 wall with wall thickness up to 1 inch, and mounts to a stud for new construction or to drywall with wing clamps in retrofit work. The kit ships with a recessed TV box, removable trim ring, old-work junction box, tamper-resistant outlet, brush-style cable access, wall plates, and mounting hardware. Legrand’s in-wall TV power kit with surge-protective outlet adds a 15-amp tamper-resistant 5-15R outlet, a recessed wall plate with an integrated brush opening, and USB Type-A connectivity, accepts right-angle TV plugs, and lists UL-approved components.
How To Run TV Wires Through A Wall: Step Order
Working in the right sequence prevents the two failures that ruin these jobs — cutting into an obstruction and running an unrated cable that has to be pulled back out.
- Pick both locations first. Mark the TV and equipment spots, then verify the upper and lower openings sit in the same stud bay.
- Inspect before cutting. Check for studs, electrical cables, plumbing, insulation, and fire blocking. A stud finder helps but does not replace careful inspection.
- Kill the power. Switch off nearby circuits before cutting or working near wiring, and confirm with a tester that they are dead.
- Mark with the manufacturer’s template. Cut only the drywall openings the kit or plates actually require.
- Set the upper and lower modules. Retrofit boxes secure with the supplied wing clamps; new-construction boxes fasten to a stud as directed.
- Run only in-wall-rated low-voltage cable. HDMI, Ethernet, coaxial, optical, and USB lines qualify when their jackets are rated for in-wall use. Leave service slack.
- Connect the kit’s power parts exactly as instructed. Never splice, bury, or extend a detachable appliance power cord inside the wall.
- Test everything before mounting. Check HDMI, Ethernet, coaxial, audio, USB, and power while the wall is still open.
Only then hang the TV, following the mount maker’s directions and keeping cables clear of pinch points and sharp bends. For readers who want a plug-and-play surface option instead of cutting drywall, our roundup of tested wire hiders for TV cables covers the paintable raceway styles that hide cords on the wall face.
What Do You Give Up With A Surface Raceway?
A paintable surface raceway skips the drywall work entirely, and it is the right call for renters, plaster walls, or anyone who does not want to open a wall. The trade-off is visible: the channel sits on the wall face, so it hides the cables without disappearing itself. Paint it to match the wall and it fades into the background, but close up you will still see a slim line running from the TV down to the outlet.
| Method | Wall Cutting Required | Best For |
|---|---|---|
| In-wall low-voltage cable routing | Two small openings | Hiding HDMI and Ethernet without a kit |
| SANUS SA-IWP1 kit | Two openings, hole saw included | DIY power plus AV in one job |
| Legrand On-Q OQ-HT2302KWH | Two openings | Retrofit or new construction, 2 × 4 walls |
| Legrand surge-protective power kit | Two openings | Right-angle plugs and USB access |
| Paintable surface raceway | None | Rentals and plaster walls |
Where DIY TV Wire Hiding Gets Risky
Electrical requirements change by state, municipality, wall construction, and the adopted edition of the National Electrical Code, so any in-wall power work should use a product specifically listed for that purpose and should follow local permitting and inspection rules. Use Legrand’s in-wall TV connection kit specs to confirm the box fits your wall before ordering.
- Never place a standard extension cord, power strip, or detachable TV cord inside drywall.
- Do not cut over an obstruction, across fire blocking, or where drilling could hit concealed utilities.
- Keep line-voltage power and low-voltage signal cable separated unless the listed enclosure and local code allow otherwise.
- Check cable ratings, connector size, bend radius, HDMI bandwidth, and run length before you close the wall.
- Recessed boxes fit the wall depth they are built for — the Legrand OQ-HT2302KWH supports standard 2 × 4 walls up to 1 inch thick, not every assembly.
- Confirm current model availability before you buy, since product lines change.
Common Questions
Can I Run A TV Power Cord Through Drywall Myself?
No. A TV’s detachable power cord, an extension cord, or a power strip inside a wall breaks electrical code and creates a fire hazard. Move power behind the TV with a listed in-wall power kit or have an electrician install a proper receptacle at the TV location.
Do Brush Plates Meet Code For Signal Cables?
Brush plates and listed low-voltage wall plates are the standard way to finish low-voltage openings, and signal cables rated for in-wall use can pass through them. Local code governs the details, so confirm the plate is listed for the installation and keep it separate from line-voltage wiring.
What If The Upper And Lower Holes Land In Different Stud Bays?
Reposition both openings before cutting; the run has to stay inside one stud bay, free of studs and fire blocking. If the wall layout makes that impossible, switch to a surface raceway so the cables stay on the wall face instead.
Sources
- Legrand. “In-Wall Power and Cable Management TV Connection Kit — New Construction/Retrofit with Outlet” Supports the OQ-HT2302KWH specs, contents, and 2 × 4 wall fit.
- SANUS. “SA-IWP1 In-Wall Power and Cable Management Kit” Supports the kit contents and the under-30-minute install claim.
- Legrand AV. “In-Wall TV Power Kit with Surge-Protective Outlet, White” Supports the 15-amp outlet, USB Type-A, and UL-approved components.